Cisco AS5300 - Universal Access Server Technical document

APPENDIX
Cabling Specifications D-1
D
Cabling Specifications
This appendix provides the following cabling and pinout information for the Cisco AS5300
universal access server:
•Console and Auxiliary Port Cables and Pinouts
•Ethernet Port Pinouts
•T1/PRI and E1/PRI Card Port Pinouts
•T1/PRI and E1/PRI Card Cable Assemblies and Pinouts
Note This appendix specifies pinouts only for the pins used. Pins not listed in the tables in this
appendix are not connected.
Console and Auxiliary Port Cables and Pinouts
The access server arrives with a console and auxiliary cable kit, which contains the cable and
adapters you need to connect a console (an ASCII terminal or PC running terminal emulation
software) or modem to your access server. The console and auxiliary cable kit includes:
•RJ-45-to-RJ-45 rollover cable. (See the next section, “Identifying a Rollover Cable,” for more
information.)
•RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL).
•RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL).
•RJ-45-to-DB-25 male DCE adapter (labeled MODEM).
For console connections, proceed to the section “Console Port Cables and Pinouts” later in this
appendix; for modem connections, proceed to the section “Auxiliary Port Signals and Pinouts” later
in this appendix.
Identifying a Rollover Cable
You can identify a rollover cable by comparing the two modular ends of the cable. Holding the cables
side-by-side, with the tab at the back, the wire connected to the pin on the outside of the left plug
should be the same color as the wire connected to the pin on the outside of the right plug. (See
Figure D-1.) If your cable was purchased from Cisco Systems, pin 1 will be white on one connector,
and pin 8 will be white on the other connector (a rollover cable reverses pins 1 and 8, 2 and 7, 3 and
6, and 4 and 5).

Cisco AS5300 Universal Access Server Chassis Installation Guide
Console and Auxiliary Port Cables and Pinouts
D-2
Figure D-1 Identifying a Rollover Cable
Console Port Cables and Pinouts
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-9 female DTE adapter (labeled
TERMINAL) to connect the console port to a PC running terminal emulation software. Figure D-2
shows how to connect the console port to a PC. Table D-1 lists the pinouts for the asynchronous
serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-9 female DTE adapter
(labeled TERMINAL).
Figure D-2 Connecting the Console Port to a PC
Table D-1 Console Port Signaling and Cabling Using a DB-9 Adapter
Console
Port (DTE)
RJ-45-to-RJ-45
Rollover Cable
RJ-45-to-DB-9
Terminal Adapter
Console
Device
Signal RJ-45 Pin RJ-45 Pin DB-9 Pin Signal
RTS 11
1 Pin 1 is connected internally to pin 8.
88 CTS
DTR 2 7 6 DSR
TxD 3 6 2 RxD
GND 4 5 5 GND
GND 5 4 5 GND
RxD 6 3 3 TxD
DSR 7 2 4 DTR
CTS 8117 RTS
Pin 1 Pin 8
H3824
Pin 1 and pin 8
should be the
same color
PC
H10569
RJ-45 to RJ-45
rollover cable
RJ-45 to DB-9 adapter
(labeled TERMINAL)
Access
server

Auxiliary Port Signals and Pinouts
Cabling Specifications D-3
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 female DTE adapter (labeled
TERMINAL) to connect the console port to a terminal. Figure D-3 shows how to connect the console
port to a terminal. Table D-1 lists the pinouts for the asynchronous serial console port, the
RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL).
Figure D-3 Connecting the Console Port to a Terminal
Auxiliary Port Signals and Pinouts
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 male DCE adapter (labeled MODEM)
to connect the auxiliary port to a modem. Figure D-4 shows how to connect the auxiliary port to a
modem. Table D-4 lists the pinouts for the asynchronous serial auxiliary port, the RJ-45-to-RJ-45
rollover cable, and the RJ-45-to-DB-25 male DCE adapter (labeled MODEM).
Figure D-4 Connecting the Auxiliary Port to a Modem
Table D-2 Console Port Signaling and Cabling Using a DB-25 Adapter
Console
Port (DTE)1
1 You can use the same cabling to connect a console to the auxiliary port.
RJ-45-to-RJ-45 Rollover
Cable
RJ-45-to-DB-25
Terminal
Adapter
Console
Device
Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal
RTS 12
2 Pin 1 is connected internally to pin 8.
85 CTS
DTR 2 7 6 DSR
TxD 3 6 3 RxD
GND 4 5 7 GND
GND 5 4 7 GND
RxD 6 3 2 TxD
DSR 7 2 20 DTR
CTS 8114 RTS
Terminal
Access
server
RJ-45 to RJ-45
rollover cable
RJ-45 to DB-25 adapter
(labeled TERMINAL)
H10570
RJ-45 to RJ-45
rollover cable
RJ-45 to DB-25 adapter
(labeled MODEM)
Modem
Access
server
H10571

Cisco AS5300 Universal Access Server Chassis Installation Guide
Ethernet Port Pinouts
D-4
Ethernet Port Pinouts
Table D-4 and Table D-5 list the pinouts for the Ethernet 10BaseT and 100BaseT ports, respectively.
Table D-3 Auxiliary Port Signaling and Cabling Using a DB-25 Adapter
AUX Port
(DTE)
RJ-45-to-RJ-45
Rollover Cable
RJ-45-to-DB-25
Modem Adapter Modem
Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal
RTS 1 8 4 RTS
DTR 2 7 20 DTR
TxD 3 6 3 TxD
GND 4 5 7 GND
GND 5 4 7 GND
RxD 6 3 2 RxD
DSR 7 2 8 DCD
CTS 8 1 5 CTS
Table D-4 10BaseT Port Pinout
RJ-45 Pin Description
1TXD+
2TXD–
3 RXD+
4–
5–
6 RXD–
7–
8–
Table D-5 100BaseT Port Pinouts
RJ-45 Pin Description
1TXD+
2TXD–
3 RXD+
4–
5–
6 RXD–
7–
8–

T1/PRI and E1/PRI Card Port Pinouts
Cabling Specifications D-5
T1/PRI and E1/PRI Card Port Pinouts
Table D-6 lists the Quad T1/PRI card port pinouts.
T1/PRI and E1/PRI Card Cable Assemblies and Pinouts
Eight serial cables are available from Cisco Systems for connecting the E1/PRI and T1/PRI card
ports.
Figure D-5 RJ-45-to-DB-15 Interface Cable
Table D-6 Quad T1/PRI Card Port Pinouts
RJ-45 Pin Description
1RXTip
2RXRing
3 RX Shield
4TXTip
5TXRing
6 TX Shield
7–
8–
Table D-7 T1/PRI and E1/PRI Card Assemblies and Pinouts
Cable Description Part Number Product Number
RJ-45 to DB-15 72-1336-01 CAB-E1-RJ45DB15
RJ-45 to DB-15 Null 72-1337-01 CAB-E1-RJ45DB15N
RJ-45 to BNC 72-1338-01 CAB-E1-RJ45BNC
RJ-45 to Twinax 72-1339-01 CAB-E1-RJ45TWIN
RJ-45 to RJ-45 TE 72-1340-01 CAB-E1-RJ45TE
RJ-45 to RJ-45 NT 72-1341-01 CAB-E1-RJ45NT
RJ-45 to RJ-45 T1 72-1342-01 CAB-E1-RJ45RJ45
RJ-45 to Bare 72-1343-01 CAB-T1-RJ45BARE
Table D-8 RJ-45-to-DB-15 Interface Cable Pinouts
RJ-45 Pin Signal Description Direction DB-15 Pin
Shield Ground Shell/Braid Shell
J1-1 RX Tip Twisted Pair #1 <— J2-3
H10982
J1
J2

Cisco AS5300 Universal Access Server Chassis Installation Guide
T1/PRI and E1/PRI Card Cable Assemblies and Pinouts
D-6
Figure D-6 RJ-45-to-BNC Interface Cable for 75-Ohm, Unbalanced Connections
J1-2 RX Ring Twisted Pair #1 <— J2-11
J1-3 RX Shield Twisted Pair #3 J2-4
J1-4 TX Tip Twisted Pair #2 —> J2-1
J1-5 TX Ring Twisted Pair #2 —> J2-9
J1-6 TX Shield Twisted Pair #4 J2-2
Table D-9 RJ-45-to-Twinax Cable Pinouts
RJ-45 Pin Signal Description Direction DB-15 Pin
Shield Ground Shell/Braid Shell
J1-1 RX Tip Twisted Pair #1 <— J2-1
J1-2 RX Ring Twisted Pair #1 <— J2-9
J1-3 RX Shield Twisted Pair #3 J2-2
J1-4 TX Tip Twisted Pair #2 —> J2-3
J1-5 TX Ring Twisted Pair #2 —> J2-11
J1-6 TX Shield Twisted Pair #4 J2-4
Table D-10 RJ-45-to-BNC Cable Pinouts
RJ-45 Pin Signal Description Direction BNC Pin
Shield Ground Shell RX, TX Shields
J1-1 RX Tip Twisted Pair #1 <— RX-Tip
J1-2 RX Ring Twisted Pair #1 <— RX-Shield
J1-3 RX Shield Twisted Pair #3 RX-Shield
J1-4 TX Tip Twisted Pair #2 —> TX-Tip
J1-5 TX Ring Twisted Pair #2 —> TX-Shield
J1-6 TX Shield Twisted Pair #4 TX-Shield
Table D-8 RJ-45-to-DB-15 Interface Cable Pinouts (continued)
RJ-45 Pin Signal Description Direction DB-15 Pin
H10660
J1
RX
TX

T1/PRI and E1/PRI Card Cable Assemblies and Pinouts
Cabling Specifications D-7
Figure D-7 RJ-45-to-Twinax Interface Cable for 120-Ohm, Balanced Connections
Figure D-8 RJ-45-to-RJ-45 Interface Cable
Table D-11 RJ-45-to-Twinax Cable Pinouts
RJ-45 Pin Signal Description Direction Twinax Pin
Shield Ground Shell RX, TX Shields
J1-1 RX Tip Twisted Pair #1 <— RX-1
J1-2 RX Ring Twisted Pair #1 <— RX-2
J1-3 RX Shield Twisted Pair #3 RX Shield
J1-4 TX Tip Twisted Pair #2 —> TX-1
J1-5 TX Ring Twisted Pair #2 —> TX-2
J1-6 TX Shield Twisted Pair #4 TX Shield
Table D-12 RJ-45-to-RJ-45 TE Cable Pinouts
RJ-45 Pin Signal Description Direction RJ-45 TE Pin
Shield Ground Shell/Braid Shield
J1-1 RX Tip Twisted Pair #1 <— J2-1
J1-2 RX Ring Twisted Pair #1 <— J2-2
J1-3 RX Shield Twisted Pair #3 J2-3
J1-4 TX Tip Twisted Pair #2 —> J2-4
J1-5 TX Ring Twisted Pair #2 —> J2-5
J1-6 TX Shield Twisted Pair #4 J2-6
Table D-13 RJ-45-to-RJ-45 NT Cable Pinouts
RJ-45 Pin Signal Description Direction Signal RJ-45 NT Pin
Shield Ground Shell/Braid Ground Shield
J1-1 RX Tip Twisted Pair #1 <— TX Tip J2-4
J1-2 RX Ring Twisted Pair #1 <— TX Ring J2-5
J1-3 RX Shield Twisted Pair #3 TX Shield J2-6
J1-4 TX Tip Twisted Pair #2 —> RX Tip J2-1
H10659
J1
RX
TX
H10983
J1
J2

Cisco AS5300 Universal Access Server Chassis Installation Guide
T1/PRI and E1/PRI Card Cable Assemblies and Pinouts
D-8
Note Because this cable has polarity, the pinouts are different depending on which end of the cable
you use.
Figure D-9 RJ-45-to-Bare Wire Interface Cable
J1-5 TX Ring Twisted Pair #2 —> RX Ring J2-2
J1-6 TX Shield Twisted Pair #4 RX Shield J2-3
Table D-14 RJ-45-to-RJ-45 T1 Cable Pinouts
RJ-45 Pin Signal Description Direction RJ-45 T1 Pin
Shield Ground Shell/Braid Shield
J1-1 RX Tip Twisted Pair #1 <— J2-1
J1-2 RX Ring Twisted Pair #1 <— J2-2
J1-3 RX Shield
J1-4 TX Tip Twisted Pair #2 —> J2-4
J1-5 TX Ring Twisted Pair #2 —> J2-5
J1-6 TX Shield
Table D-15 RJ-45-to-Bare Wire Inteface Cable Pinouts
RJ-45 Pin Signal Description Direction Bare
Shield Ground Braid
J1-1 RX Tip Twisted Pair #1 <— WIRE-1
J1-2 RX Ring Twisted Pair #1 <— WIRE-2
J1-3 RX Shield
J1-4 TX Tip Twisted Pair #2 —> WIRE-3
J1-5 TX Ring Twisted Pair #2 —> WIRE-4
J1-6 TX Shield
Table D-13 RJ-45-to-RJ-45 NT Cable Pinouts (continued)
RJ-45 Pin Signal Description Direction Signal RJ-45 NT Pin
H10984
J1

T1/PRI and E1/PRI Card Cable Assemblies and Pinouts
Cabling Specifications D-9
Figure D-10 /E1 (8) PRI Cable (72-1492-xx) Used in an Access Server Shelf
Figure D-11 T1/E1 (8) PRI Cable (72-1492-xx)
Table D-16 Access Server Shelf T1/E1 (8) PRI Cable (72-1492-xx)
RJ-45 Plug
Shelf
Connection
RJ-45
Pin
Twisted
Pair Signal Description 36 Pin
1 (tan) PRI 0 1 2 T1-1 Rx– T1/E1 PRI Receive – 20
2 T1-1 Rx+ T1/E1 PRI Receive + 2
4 1 T1-1 Tx– T1/E1 PRI Transmit – 21
5 T1-1 Tx+ T1/E1 PRI Transmit + 3
2 (tan) PRI 1 1 2 T1-2 Rx– T1/E1 PRI Receive – 22
2 T1-2 Rx+ T1/E1 PRI Receive + 4
4 1 T1-2 Tx– T1/E1 PRI Transmit – 23
5 T1-2 Tx+ T1/E1 PRI Transmit + 5
3 (tan) PRI 2 1 2 T1-3 Rx– T1/E1 PRI Receive – 24
2 T1-3 Rx+ T1/E1 PRI Receive + 6
10672
72-1463-xx
72-1464-xx
Odd-numbered
connectors from
J13 through J39
Even-numbered
connectors from
J14 through J40
16484
18
1
P1
P2
P3
P4
P5
P6
P7
P8
19
36

Cisco AS5300 Universal Access Server Chassis Installation Guide
T1/PRI and E1/PRI Card Cable Assemblies and Pinouts
D-10
4 1 T1-3 Tx– T1/E1 PRI Transmit – 25
5 T1-3 Tx+ T1/E1 PRI Transmit + 7
4 (tan) PRI 3 1 2 T1-4 Rx– T1/E1 PRI Receive – 26
2 T1-4 Rx+ T1/E1 PRI Receive + 8
4 1 T1-4 Tx– T1/E1 PRI Transmit – 27
5 T1-4 Tx+ T1/E1 PRI Transmit + 9
4 1 T1-1 Tx– T1/E1 PRI Transmit – 21
5 T1-1 Tx+ T1/E1 PRI Transmit + 3
5 (tan) PRI 4 1 2 T1-2 Rx– T1/E1 PRI Receive – 28
2 T1-2 Rx+ T1/E1 PRI Receive + 10
4 1 T1-2 Tx– T1/E1 PRI Transmit – 29
5 T1-2 Tx+ T1/E1 PRI Transmit + 11
6 (tan) PRI 5 1 2 T1-2 Rx– T1/E1 PRI Receive – 30
2 T1-2 Rx+ T1/E1 PRI Receive + 12
4 1 T1-2 Tx– T1/E1 PRI Transmit – 31
5 T1-2 Tx+ T1/E1 PRI Transmit + 13
7 (tan) PRI 6 1 2 T1-3 Rx– T1/E1 PRI Receive – 32
2 T1-3 Rx+ T1/E1 PRI Receive + 14
4 1 T1-3 Tx– T1/E1 PRI Transmit – 33
5 T1-3 Tx+ T1/E1 PRI Transmit + 15
8 (tan) PRI 7 1 2 T1-4 Rx– T1/E1 PRI Receive – 34
2 T1-4 Rx+ T1/E1 PRI Receive + 16
4 1 T1-4 Tx– T1/E1 PRI Transmit – 35
5 T1-4 Tx+ T1/E1 PRI Transmit + 17
Table D-16 Access Server Shelf T1/E1 (8) PRI Cable (72-1492-xx) (continued)
RJ-45 Plug
Shelf
Connection
RJ-45
Pin
Twisted
Pair Signal Description 36 Pin