Cisco 6503 - Catalyst Firewall Security Sys User manual

Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]
Catalyst 6500 Series Switches
Installation Guide
September 2010
Text Part Number: OL-5781-08

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at
www.cisco.com/web/siteassets/legal/trademark.html. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not
imply a partnership relationship between Cisco and any other company. (1005R)
Catalyst 6500 Series Switches Installation Guide
Copyright © 1999–2010 Cisco Systems, Inc. All rights reserved.

v
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
CONTENTS
Preface xi
Audience xi
Organization xi
Conventions iii-xii
Statement 1071—Warning Definition xiv
Related Documentation xix
CHAPTER 1Product Overview 1-1
Catalyst 6503 Switch 1-2
Catalyst 6503-E Switch 1-8
Catalyst 6504-E Switch 1-13
Catalyst 6506 Switch 1-18
Catalyst 6506-E Switch 1-24
Catalyst 6509 Switch 1-30
Catalyst 6509-E Switch 1-36
Catalyst 6509-NEB Switch 1-42
Catalyst 6509-NEB-A Switch 1-49
Catalyst 6509-V-E Switch 1-55
Catalyst 6513 Switch 1-61
Catalyst 6513-E Switch 1-67
CHAPTER 2Preparing for Installation 2-1
Safety 2-2
Site Requirements 2-2
Temperature 2-3
Air Flow 2-3
Humidity 2-14
Altitude 2-14
Dust and Particles 2-15
Corrosion 2-15
Electromagnetic and Radio Frequency Interference 2-15
Shock and Vibration 2-16

Contents
vi
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Power Source Interruptions 2-16
System Grounding 2-17
Maintaining Safety with Electricity 2-19
Preventing Electrostatic Discharge Damage 2-20
Power Requirements 2-22
Power Connection Guidelines for AC-Powered Systems 2-22
Power Connection Guidelines for DC-Powered Systems 2-23
Cabling Requirements 2-24
Site Preparation Checklist 2-24
CHAPTER 3Installing the Switch 3-1
Rack-Mounting Guidelines 3-3
Unpacking the Switch 3-5
Chassis Installation Kits and Cable Guides 3-5
Installing a Catalyst 6503 or Catalyst 6503-E Switch Chassis 3-8
Installation Accessory Kit 3-8
Rack-Mount Brackets on the Catalyst 6503 and the Catalyst 6503-E Switch Chassis 3-8
Rack-Mounting the Chassis 3-9
What is Next 3-11
Optional Installation Kits 3-11
Installing a Catalyst 6504-E Switch Chassis 3-12
Installation Accessory Kit 3-12
L Brackets on the Catalyst 6504-E Switch Chassis 3-12
Rack-Mounting the Chassis 3-13
What is Next 3-16
Optional Installation Kits 3-16
Installing a Catalyst 6506 or Catalyst 6506-E Switch Chassis 3-17
Installation Accessory Kits 3-17
L Brackets on the Catalyst 6506 and the Catalyst 6506-E Switch Chassis 3-17
Installing the 3 RU Rack-Mount Shelf Kit 3-18
Rack-Mounting the Chassis 3-19
What is Next 3-20
Optional Installation Kits 3-21

Contents
vii
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Installing a Catalyst 6509 or Catalyst 6509-E Switch Chassis 3-21
Installation Accessory Kits 3-21
L Brackets on the Catalyst 6509 and Catalyst 6509-E Switches 3-21
Installing the 3 RU Rack-Mount Shelf Kit 3-22
Rack-Mounting the Chassis 3-23
What is Next 3-25
Optional Installation Kits 3-25
Installing a Catalyst 6509-NEB or Catalyst 6509-NEB-A Switch Chassis 3-26
Installation Accessory Kits 3-26
L Brackets and the Optional Cable Guide on the Catalyst 6509-NEB Switch 3-26
L Brackets on the Catalyst 6509-NEB-A Switch Chassis 3-27
Installing the 3 RU Rack-Mount Shelf Kit 3-28
Rack-Mounting the Chassis 3-29
Installing the Cable Management System (Catalyst 6509-NEB-A Only) 3-31
What is Next 3-35
Optional Installation Kits 3-35
Installing a Catalyst 6509-V-E Switch Chassis 3-36
Installation Accessory Kit 3-36
L Brackets on the Catalyst 6509-V-E Switch Chassis 3-36
Installing the 3 RU Rack-Mount Shelf 3-37
Rack-Mounting the Chassis 3-38
Installing the Cable Management System (Optional) 3-40
What is Next 3-42
Optional Installation Kits 3-42
Installing a Catalyst 6513 or Catalyst 6513-E Switch Chassis 3-42
Installation Accessory Kit 3-42
L Brackets on the Catalyst 6513 and Catalyst 6513-E Switch Chassis 3-43
Installing the 3 RU Rack-Mount Shelf Kit 3-44
Rack-Mounting the Chassis 3-45
What is Next 3-46
Optional Installation Kits 3-47
Generic Installation Procedures 3-47
Installing the 3 RU Rack-Mount Shelf Kit 3-47
Installing the Rubber Feet Kit 3-50
Installing the Stabilizer Bracket Kit 3-50
Establishing the System Ground 3-52
Required Tools and Equipment 3-53
Connecting the System Ground 3-53
Installing the Power Supplies in the Switch Chassis 3-61

Contents
viii
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Attaching the Interface Cables 3-61
Connecting the Supervisor Engine Console Port 3-61
Connecting the Supervisor Engine Uplink Ports 3-63
Using the Catalyst 6509-V-E Cable Management System 3-78
Verifying Switch Chassis Installation 3-84
Online Diagnostics 3-84
CHAPTER 4Removal and Replacement Procedures 4-1
Online Insertion and Removal 4-1
Removing and Installing the AC-Input Power Supplies 4-2
Removing and Installing the 950 W and 1400 W AC-Input Power Supplies 4-3
Removing and Installing the 2700 W AC-Input Power Supply 4-6
Removing and Installing the 1000 W, 1300 W, 2500 W, 3000 W, 4000 W, 6000 W, and 8700 W
AC-Input Power Supplies 4-9
Removing and Installing the DC-Input Power Supplies 4-15
Removing and Installing a 950 W DC-Input Power Supply 4-15
Removing and Installing a 1300 W or 2500 W DC-Input Power Supply 4-19
Removing and Installing the 2700 W DC-Input Power Supply 4-27
Removing and Installing a 4000 W DC-Input Power Supply 4-36
Removing and Installing a 6000 W DC-Input Power Supply 4-58
Removing and Installing PEMs 4-75
Required Tools 4-76
Removing the AC-Input PEM 4-76
Installing the AC-Input PEM 4-78
Removing the DC-Input PEM 4-78
Installing the DC-Input PEM 4-80
Removing and Installing the Fan Tray 4-82
Required Tools 4-82
Removing the Fan Tray 4-83
Installing the Fan Assembly 4-92
Checking the Installation 4-92
Installing the Air Filter Assembly on a Catalyst 6509-NEB-A Switch or a Catalyst 6509-V-E
(Optional) 4-93
Checking the Air Filter 4-98
Installing the Remote Power Cycling Feature Control Wires (Optional) 4-98
Required Tools and Components 4-99
Installing the Remote Power-Cycling Control Wires 4-99
Installing the Ferrite Bead 4-100

Contents
ix
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
APPENDIX APower Supply Specifications A-1
Power Supply Compatibility Matrix A-2
950 W AC-Input and DC-Input Power Supplies A-5
950 W Power Supply Specifications A-6
950 W Power Supply AC Power Cords A-9
1000 W AC-Input Power Supply A-10
1000 W Power Supply Specifications A-11
1000 W Power Supply AC Power Cords A-13
1300 W AC-Input and DC-Input Power Supplies A-13
1300 W Power Supply Specifications A-15
1300 W Power Supply AC Power Cords A-17
1400 W AC-Input Power Supply A-18
1400 W Power Supply Specifications A-19
1400 W Power Supply AC Power Cords A-21
2500 W AC-Input and DC-Input Power Supplies A-23
2500 W Power Supply Specifications A-24
2500 W Power Supply AC Power Cords A-28
2700 W AC-Input and DC-Input Power Supplies A-29
2700 W Power Supply Specifications A-31
2700 W Power Supply AC Power Cords A-35
3000 W AC-Input Power Supply A-36
3000 W Power Supply Specifications A-37
3000 W Power Supply AC Power Cords A-40
4000 W AC-Input and DC-Input Power Supplies A-41
4000 W Power Supply Specifications A-42
4000 W Power Supply AC Power Cords A-46
6000 W AC-Input and DC-Input Power Supplies A-46
6000 W Power Supply Specifications A-48
6000 W Power Supply AC Power Cords A-53
8700 W AC-Input Power Supply A-54
8700 W Power Supply Specifications A-55
Remote Power Cycling Feature A-60
8700 W Power Supply AC Power Cords A-62
AC Power Cord Illustrations A-63
Power Supply Redundancy A-73
APPENDIX BTransceivers, Module Connectors, and Cable Specifications B-1
Pluggable Transceivers B-1

Contents
x
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
100-MB Transceivers B-1
1-GB Transceivers B-3
10-GB Transceivers B-10
WDM Transceivers B-17
Module Connectors B-24
RJ-45 Connector B-24
RJ-21 Connector B-25
RJ-21 Connector (WS-X6624-FXS Only) B-27
SC Connector B-28
MT-RJ Connector B-29
LC Connector B-30
Cables B-31
Console Port Mode Switch B-33
Identifying a Rollover Cable B-33
Console Port Mode 1 Signaling and Pinouts B-34
Console Port Mode 2 Signaling and Pinouts B-35
Mode-Conditioning Patch Cord B-36
Cleaning the Fiber-Optic Connectors B-38
APPENDIX CRepacking the Switch C-1
APPENDIX DChassis and Module Power and Heat Values D-1
APPENDIX ETroubleshooting E-1
Getting Started E-1
Solving Problems at the System Component Level E-2
Identifying Startup Problems E-3
Troubleshooting the Power Supply E-4
Troubleshooting the Fan Assembly E-5
Troubleshooting Modules E-5
STATUS LED Indications E-5
Contacting Customer Service E-7
I NDEX

xi
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
This preface describes who should read the Catalyst 6500 Series Switches Installation Guide, how it is
organized, and its document conventions.
Audience
Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install,
replace, or service the equipment described in this publication.
Organization
This publication is organized as follows:
Chapter Title Description
Chapter 1 Product Overview Describes and lists the hardware features and
functionality of the Catalyst 6500 series switches. The
chapter contains illustrations of the chassis and
specifications tables for the chassis.
Chapter 2 Preparing for Installation Describes things you need to consider when preparing
your site before installing the Catalyst 6500 series
switch.
Chapter 3 Installing the Switch Describes how to install your Catalyst 6500 series
switch. Procedures are provided for installing chassis in
rack enclosures, freestanding with stability brackets
installed, and freestanding with rubber feet installed.
Chapter 4 Removal and
Replacement Procedures
Provides procedures for removing and installing chassis
components.
Appendix A Power Supply
Specifications
Provides illustrations and specification tables for the
available Catalyst 6500 series switch AC-input and
DC-input power supplies. Illustrations and
specifications tables are also provided for the supported
AC power cords.

xii
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Conventions
Conventions
This publication uses the following conventions:
Appendix B Transceivers, Module
Connectors, and Cable
Specifications
Gives brief descriptions of the different types of copper
and optical transceiver modules, physical connectors,
and the cables used with the Catalyst 6500 series
switches.
Appendix C Repacking the Switch Provides procedures to repack your Catalyst 6500 series
switch if you need to return it to the factory.
Appendix D Chassis and Module
Power and Heat Values
Provides listings of the power consumption and heat
dissipation values for the Catalyst 6500 series switch
chassis and modules.
Appendix E Troubleshooting Provides troubleshooting guidelines for the initial
hardware installation and suggests steps to help isolate
and resolve problems.
Chapter Title Description
Convention Description
boldface font Commands, command options, and keywords are in
boldface.
italic font Arguments for which you supply values are in italics.
[ ] Elements in square brackets are optional.
{ x | y | z } Alternative keywords are grouped in braces and
separated by vertical bars.
[ x | y | z ] Optional alternative keywords are grouped in brackets
and separated by vertical bars.
string A nonquoted set of characters. Do not use quotation
marks around the string or the string will include the
quotation marks.

xiii
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Conventions
Notes use the following conventions:
Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the
publication.
Cautions use the following conventions:
Caution Means reader be careful. In this situation, you might do something that could result in equipment
damage or loss of data.
screen font Terminal sessions and information the system displays
are in screen font.
boldface screen
font
Information you must enter is in boldface screen font.
italic screen font Arguments for which you supply values are in italic
screen font.
^The symbol ^ represents the key labeled Control. For
example, the key combination ^D in a screen display
means hold down the Control key while you press the D
key.
< > Nonprinting characters, such as passwords, are in angle
brackets.
Convention Description

xiv
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Conventions
Warnings use the following conventions:
Statement 1071—Warning Definition
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS

xv
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Conventions
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES

xvi
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Conventions
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR

xvii
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Conventions
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER

xviii
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Conventions

xix
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Related Documentation
Related Documentation
For additional Catalyst 6500 series switch information, refer to these publications:
• Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches
• Catalyst 6500 Series Switch Quick Software Configuration Guide
• Catalyst 6500 Series Switch Module Installation Guide
• Catalyst 6500 Series Switch Software Configuration Guide
• Catalyst 6500 Series Switch Command Reference
• Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide
• Catalyst 6500 Series Switch Cisco IOS Command Reference
• ATM Software Configuration and Command Reference—Catalyst 5000 Family and Catalyst 6000
Family Switches
• Catalyst 6500 Series Switch System Message Guide
• For information about MIBs, refer to this URL:
http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

xx
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Preface
Related Documentation
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS Ver s i o n 2.0.