Cisco ME 3400E User manual

GETTING STARTED GUIDE
Cisco ME 3400E Ethernet Access Switch Getting Started Guide
INCLUDING LICENSE AND WARRANTY
1About this Guide, page 2
2Taking Out What You Need, page 2
3Initial Setup, page 5
4Managing the Switch through the CLI, page 8
5Rack-Mounting the Switch, page 9
6Connecting to the Switch Ports, page 12
7In Case of Difficulty, page 13
8Obtaining Documentation and Submitting a Service Request, page 15
9Cisco 90-Day Limited Hardware Warranty Terms, page 15

2
1 About this Guide
This guide provides instructions on how to install and configure your Cisco Metro Ethernet (ME) 3400E Ethernet Access switch.
Also covered are switch management options, basic rack-mounting procedures, port and module connections, power connection
procedures, and troubleshooting help.
For additional installation and configuration information, see the Cisco ME 3400E switch documentation on Cisco.com. For
system requirements, important notes, limitations, open and resolved bugs, and last-minute documentation updates, see the
release notes, also on Cisco.com.
When you use the online publications, refer to the documents that match the Cisco IOS software version that is running on the
switch. Look on the switch rear panel to locate the software version or enter the show version command from the command-line
interface (CLI).
Before you set up your switch, and to see translations of safety warnings, review the warnings in the Regulatory Compliance
and Safety Information for the Cisco ME 3400E Ethernet Access Switch on the documentation CD or Cisco.com.
2 Taking Out What You Need
1. Unpack and remove the switch and the accessory kit from the shipping box.
2. Return the packing material to the shipping container, and save it for future use.
3. Verify that you have received the items shown in the “Shipping Box Contents” section on page 3. If any item is missing or
damaged, contact your Cisco representative or reseller for instructions. Some switch models might include additional items,
and you might need to supply or to order some optional items.
Equipment That You Supply to Set Up Your Switch
You need:
•PC
•RJ-45-to-DB-9 adapter cable (if you did not order one with your switch)
•Ethernet (Category 5) straight-through cable (as shown)

3
Shipping Box Contents
The items shipped with your switch depend on the switch model, the options that you choose, and the type of
power-supply module. Some items shown are optional, and your switch might look different.
These items ship with the Cisco ME 3400E-24TS-M and the Cisco ME 3400EG-12CS-M switches:
1Cisco ME 3400E switch 7Cable guide
2Documentation 8Four number-8 Phillips machine screws
3AC power cord 9Four number-12 Phillips truss-head screws
4Power cord bail and bushing 10 Six number-8 Phillips flat-head screws
5DC terminal block 11 One black Phillips machine screw
6Two 19-inch mounting brackets
1
10
9
8
7
6
5
4
3
2
11
Cisco ME 3400E
Ethernet Access Switch
Documentation
Documentation
CD
281098

4
These items ship with the Cisco ME 3400EG-2CS-A switch:
Safety Warnings
Translations of these warning statements and a complete list of warnings that are applicable to this switch appear in the
Regulatory Compliance and Safety Information for the Cisco ME 3400E Ethernet Access Switches document that shipped with
your switch.
Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and
watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld
the metal object to the terminals. Statement 43
Warning Do not stack the chassis on any other equipment. If the chassis falls, it can cause severe bodily injury and
equipment damage. Statement 48
This warning applies to only the Cisco ME 3400E-24TS-M and the Cisco ME 3400EG-12CS-M switches:
Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003
1Cisco ME 3400E switch 6Cable guide
2Documentation 7Four number-10 Phillips truss-head screws
3AC power cord 8Four number-12 Phillips truss-head screws
4Four rubber feet 9Two number-10 Phillips flat-head screws
5Two 19-inch mounting brackets 10 One black Phillips machine screw
10
9
8
7
6
5
12
34
Cisco ME 3400E
Ethernet Access Switch
Documentation
Documentation
CD
281099

5
Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if
you are uncertain that suitable grounding is available. Statement 1024
This warning applies to only the Cisco ME 3400E-24TS-M and the Cisco ME 3400EG-12CS-M switches:
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation.
Install only in accordance with national and local wiring regulations. Statement 1045
Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended
ambient temperature of: 122°F (50°C) Statement 1047
Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074
3 Initial Setup
When you set up the switch to enter the initial IP information, the switch can then connect to local routers and the Internet. For
further configuration, access the switch CLI.
Your switch might look different from the illustrations, but the instructions apply to all the Cisco ME switches. Some
instructions depend on whether the switch uses AC or DC power.
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to
ensure that the system remains stable. The following guidelines are provided to ensure your safety:
•This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
•When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the
bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Statement 1006

6
Step 1 Obtain this information from your network
administrator before you start the setup program.
•Switch IP address
•Subnet mask (IP netmask)
•Default gateway (router)
•Enable secret password
•Enable password
•Telnet password
Step 2 Connect the adapter cable to the console
connector on the switch front panel. Connect the
other end of the cable to the Ethernet port on
your DHCP-enabled PC.
You must supply the console cable if you did not
order one with your switch.
Step 3 Start a terminal-emulation application such as Hyperterminal or ProcommPlus.
Step 4 Configure the baud rate and character format of
the PC or terminal to match these console port
default characteristics.
•9600 baud
•8 data bits
•1 stop bit
•No parity
•None (flow control)
Step 5 Connect the switch to a power source. For
information on power usage, see the technical
specifications in the hardware installation guide.
This illustration shows a DC-powered switch.
Connect one DC terminal block to the power
connector on the switch front panel. Connect the
other end of the cable to a DC outlet.
For detailed instructions about connecting to an
AC or DC power source, see “Chapter 3,
Installing and Removing the Power-Supply
Modules,” in the hardware installation guide.
Step 6 Power on the switch.
Step 7 Wait for the switch to complete POST. It might take several minutes for the switch to complete POST.
Step 8 Verify that POST has completed. The System
(SYST) LED blinks green while the switch starts
up. It turns solid green after POST succeeds. If the
switch fails POST, the System LED turns amber.
Contact Cisco Systems immediately if your switch fails POST.
Step 9 When you see the prompt, press Return or Enter.Press RETURN to get started!
281100
281101

7
Completing the Initial Configuration
Follow these steps to complete the setup program and to create the initial configuration for the switch.
Step 1 After you press Enter or Return at the prompt to start the initial configuration setup program, enter Yes at these
prompts:
Would you like to terminate autoinstall? [yes/no]: yes
Would you like to enter the initial configuration dialog? [yes/no]: yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system.
Would you like to enter basic management setup? [yes/no]: yes
Step 2 Enter a hostname for the switch, and press Return.
The hostname is limited to 20 characters. Do not use -n, where n is a number, as the last character in a hostname
for any switch.
Enter host name [Switch]: host_name
Step 3 Enter an enable secret password, and press Return.
The password must be different from the enable secret password and can be from 1 to 25 alphanumeric characters,
can start with a number, is case sensitive, allows spaces, but ignores leading spaces. The secret password is
encrypted, and the enable password is in plain text.
Enter enable secret: secret_password
Step 4 Enter an enable password, and press Return.
Enter enable password: enable_password
Step 5 Enter a virtual terminal (Telnet) password, and press Return.
The password can be from 1 to 25 alphanumeric characters, is case sensitive, allows spaces, but ignores leading
spaces.
Enter virtual terminal password: terminal-password
Step 6 (Optional) Configure Simple Network Management Protocol (SNMP) by responding to the prompts. You can also
configure SNMP later through the CLI. To configure SNMP later, enter no.
Configure SNMP Network Management? [no]: no
Step 7 At the prompt, enter either FastEthernet0 or the VLAN name (usually VLAN1) as the interface connected to the
management network, and press Return.
Enter interface name used to connect to the
management network from the above interface summary: FastEthernet0
Step 8 Enter Yes after the prompt, and then enter the
switch IP address and subnet mask. Press
Return.
The IP address and subnet mask shown to the
right are examples.
Configuring interface vlan1:
Configure IP on this interface? [yes]: yes
IP address for this interface: 10.4.120.106
Subnet mask for this interface [255.0.0.0]: 255.0.0.0

8
4 Managing the Switch through the CLI
After you install the switch in your network, you can enter Cisco IOS commands and parameters through the CLI. Access the
CLI either by connecting your PC directly to the switch console port or through a Telnet session from a remote PC or
workstation.
Other Management Options
You can use SNMP management applications such as CiscoWorks Small Network Management Solution (SNMS) and
HP OpenView to configure and manage the switch. You also can manage it from an SNMP-compatible workstation that is
running platforms such as HP OpenView or SunNet Manager.
Step 9 Enter N when the prompt asks if you want to
enable the switch as a cluster command switch.
This switch will be a standalone switch that
does not support clustering.
Would you like to enable as a cluster
command switch? [yes/no]: no
The switch displays its initial configuration, as
shown on the right.
The following configuration command script was created:
hostname switch1
enable secret 5 $1$Ulq8$DlA/OiaEbl90WcBPd9cOn1
enable password enable_password
line vty 0 15
password terminal-password
no snmp-server
!
no ip routing
!
interface Vlan1
no shutdown
ip address 10.4.120.106 255.0.0.0
!
interface FastEthernet0/1
!
interface FastEthernet0/2
...<output abbreviated>
interface FastEthernet1/0/3
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
end
Step 10 These choices appear:
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
If you want to save the configuration and use it the next time the switch reboots, save it in NVRAM
by selecting option 2.
Enter your selection [2]:2
Make your selection, and press Return.
Step 11 Disconnect the switch from the PC, and install the switch in your network. See the “Managing the Switch through
the CLI” section on page 8 for information about configuring and managing the switch.
If you need to rerun the initial configuration dialog, see the “Resetting the Switch” section on page 13.

9
The Cisco IE2100 Series Configuration Registrar is a network management device that works with embedded CNS agents in
the switch software. You can use IE2100 to automate initial configurations and configuration updates on the switch.
See the “Accessing Troubleshooting Information on Cisco.com” section on page 14 for a list of supporting documentation.
5 Rack-Mounting the Switch
This section covers 19-inch rack-mounting. For alternate mounting procedures, such as installing the switch in a 23-inch,
24-inch, or a European Telecommunication Standards Institute (ETSI) rack, or installing a switch on a wall, see the
Cisco ME 3400E Ethernet Access Switch Hardware Installation Guide on Cisco.com.
Equipment That You Supply
You need to supply a number-2 Phillips screwdriver to rack-mount the switch. You must supply other types of mounting
hardware such as ETSI brackets or other hardware that does not ship with the switch.
Before You Begin
When you determine where to install the switch, verify that these guidelines are met:
•Airflow around the switch and through the vents is
unrestricted.
•Clearance to the switch front and rear panels meets these
conditions:
– You can easily see the System, MGMT, Alarm, port,
and power-supply LEDS.
– You have sufficient access to ports for cabling.
– The AC power cord can reach from the power outlet
to the front-panel connector.
– The DC power cable can reach from the power outlet
to the front-panel connector.
•Cabling is away from sources of electrical noise, such as
radios, power lines, and fluorescent lighting fixtures.
•For 10/100 or 10/100/1000 ports, the cable length from a
switch to an attached device cannot exceed 328 feet
(100 meters).
•For cable lengths for small form-factor pluggable (SFP)
modules, see the documentation that shipped with the
module.
•Temperature around the switch does not exceed 122°F
(50°C).
•Humidity around the switch does not exceed 95 percent.
•Altitude at the installation site is not greater than
10,000 feet.

10
Attaching the Brackets
Use four Phillips flat-head screws to attach the long side of the brackets to the switches in one of mounting positions (for all
but the Cisco ME 3400EG-2CS-A switch):
Use the tab on the bracket and the Phillips flat-head screw to attach the short side of each bracket to the
Cisco ME 3400EG-2CS-A switch in this mounting position:
1Front-mounting position 3Mid-rack mounting position (telco rack)
2Number-8 Phillips flat-head screws 4Rear-mounting position
PSU OK +24V -48V
DC
PSU OK+24V -48V
DC
4
3
2
1
281102
280836