Cisco Aironet 1000 Series Manual

Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware
Installation Guide
First Published: 2019-12-25
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

CONTENTS
Preface vii
PREFACE
Document Conventions vii
Obtaining Documentation and Submitting a Service Request ix
Product Overview 1
CHAPTER 1
Switch Models 1
Front Panel 2
PoE Ports 4
10/100/1000 Ports 4
Console Ports 4
USB Type A Port 5
SFP Module Slots 5
LEDs 6
System LED 7
Port LEDs 7
Rear Panel 7
Internal Power Supply 8
Security Slot 9
Network Configurations 9
Switch Installation 11
CHAPTER 2
Safety Warnings 11
Box Contents 15
Tools and Equipment 16
Installation Guidelines 17
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
ii
Contents

Verifying Switch Operation 17
Installing the Switch 18
Rack-Mounting 18
Attaching the Rack-Mount Brackets 19
Mounting a 24-Port or 48-Port Switch in a Rack 21
Wall-Mounting 22
Attaching the Brackets for Wall-Mounting 22
Mounting on a Wall 23
Installing the Switch on a Table or Shelf 24
After Switch Installation 25
Installing the Power Cord Retainer (Optional) 25
Installing SFP Modules 27
Installing an SFP or SFP+ Module 27
Removing an SFP or SFP+ Module 29
Connecting to SFP or SFP+ Modules 30
Connecting to Fiber-Optic SFP or SFP+ Modules 30
Connecting to 1000BASE-T SFP 31
10/100/1000 PoE+ Port Connections 32
10/100/1000 Ethernet Port Connections 33
Auto-MDIX Connections 33
Troubleshooting 35
CHAPTER 3
Diagnosing Problems 35
Switch POST Results 35
System LEDs 35
Switch Connections 35
Bad or Damaged Cable 35
Ethernet and Fiber-Optic Cables 36
Link Status 36
10/100/1000 Port Connections 36
10/100/1000 PoE+ Port Connections 36
SFP and SFP+ Module 37
Interface Settings 37
Ping End Device 37
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
iii
Contents

Spanning Tree Loops 37
Switch Performance 38
Speed, Duplex, and Autonegotiation 38
Autonegotiation and Network Interface Cards 38
Cabling Distance 38
Finding the Switch Serial Number 38
Technical Specifications 41
APPENDIX A
Physical Specifications 41
Environmental Specifications 42
Power Requirements 43
PoE Power Consumption 44
Connector and Cable Specifications 45
APPENDIX B
Connector Specifications 45
10/100/1000 Ports (Including PoE) 45
SFP Module Connectors 45
Cables and Adapters 46
SFP Module Cables 46
Cable Pinouts 47
Console Port Adapter Pinouts 48
Configuring the Switch 51
APPENDIX C
Configuring the Switch Using the Configuration Setup Wizard 51
Quick Setup: Accessing the Configuration Setup Wizard 51
Completing the Configuration Setup Wizard 53
Configuring the Switch Using the CLI 53
Accessing the CLI Through the Console Port 53
Connecting the RJ-45 Console Port 54
Connecting the USB Console Port 54
Installing the Cisco Microsoft Windows USB Device Driver 55
Installing the Cisco Microsoft Windows XP USB Driver 55
Installing the Cisco Microsoft Windows 2000 USB Driver 55
Installing the Cisco Microsoft Windows 7 USB Driver 56
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
iv
Contents

Uninstalling the Cisco Microsoft Windows USB Driver 56
Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver 56
Uninstalling the Cisco Microsoft Windows 7 USB Driver 57
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
v
Contents

Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
vi
Contents

Preface
•Document Conventions , on page vii
•Obtaining Documentation and Submitting a Service Request, on page ix
Document Conventions
This document uses the following conventions:
DescriptionConvention
Both the ^symbol and Ctrl represent the Control (Ctrl) key on a keyboard. For
example, the key combination ^D or Ctrl-D means that you hold down the Control
key while you press the D key. (Keys are indicated in capital letters but are not
case sensitive.)
^ or Ctrl
Commands and keywords and user-entered text appear in bold font.bold font
Document titles, new or emphasized terms, and arguments for which you supply
values are in italic font.
Italic font
Terminal sessions and information the system displays appear in courier font.Courier font
Bold Courier font indicates text that the user must enter.Bold Courier font
Elements in square brackets are optional.[x]
An ellipsis (three consecutive nonbolded periods without spaces) after a syntax
element indicates that the element can be repeated.
...
A vertical line, called a pipe, indicates a choice within a set of keywords or
arguments.
|
Optional alternative keywords are grouped in brackets and separated by vertical
bars.
[x | y]
Required alternative keywords are grouped in braces and separated by vertical
bars.
{x | y}
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
vii

DescriptionConvention
Nested set of square brackets or braces indicate optional or required choices within
optional or required elements. Braces and a vertical bar within square brackets
indicate a required choice within an optional element.
[x {y | z}]
A nonquoted set of characters. Do not use quotation marks around the string or
the string will include the quotation marks.
string
Nonprinting characters such as passwords are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning of a line of code
indicates a comment line.
!, #
Reader Alert Conventions
This document may use the following conventions for reader alerts:
Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual.
Note
Means the following information will help you solve a problem.
Tip
Means reader be careful. In this situation, you might do something that could result in equipment damage or
loss of data.
Caution
Means the described action saves time. You can save time by performing the action described in the paragraph.
Timesaver
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate
its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Warning
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
viii
Preface
Preface

Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information,
see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco
technical documentation, at:
http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
ix
Preface
Obtaining Documentation and Submitting a Service Request

Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
x
Preface
Obtaining Documentation and Submitting a Service Request

CHAPTER 1
Product Overview
The Cisco Catalyst 1000 Series switches are fixed-configuration, Gigabit Ethernet switches that provide
entry-level enterprise-class Layer 2 access for branch offices, conventional workspace, and out-of-wiring
closet applications.
Cisco Catalyst 1000 Series switches provide support for the following features:
• 24 or 48 Gigabit Ethernet ports with line-rate forwarding performance.
• 4 Gigabit Small Form-Factor Pluggable (SFP/SFP+) uplinks.
• Power over Ethernet Plus (PoE+) support with up to 370W of PoE budget and Perpetual PoE.
• Fanless operation with operational temperature up to 50°C for deployment outside the wiring closet.
• Reduced power consumption and advanced energy management.
• RJ-45 and USB Mini-Type B console ports.
• USB Type A port supports file system.
•Switch Models, on page 1
•Front Panel, on page 2
•Rear Panel, on page 7
•Network Configurations, on page 9
Switch Models
Table 1: Cisco Catalyst 1000 24-Port and 48-Port Switch Models and Description
DescriptionSwitch Model
24 10/100/1000 Ethernet ports; four 1-Gigabit Ethernet small form-factor pluggable
(SFP) module uplink slots
C1000-24T-4G-L
24 10/100/1000 PoE+ ports (PoE budget of 195W); four 1-Gigabit Ethernet SFP
module uplink slots
C1000-24P-4G-L
24 10/100/1000 PoE+ ports (PoE budget of 370W); four 1-Gigabit Ethernet SFP
module uplink slots
C1000-24FP-4G-L
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
1

DescriptionSwitch Model
48 10/100/1000 Ethernet ports; four 1-Gigabit Ethernet SFP module uplink slotsC1000-48T-4G-L
48 ports; 12x10/100/1000 PoE+ ports (PoE budget of 370W) and 36x10/100/1000
Ethernet ports; four 1-Gigabit Ethernet SFP module uplink slots
C1000-48P-4G-L
48 10/100/1000 PoE+ ports (PoE budget of 740W); four 1-Gigabit Ethernet SFP
module uplink slots
C1000-48FP-4G-L
24 10/100/1000 Ethernet ports; four 10-Gigabit Ethernet small form-factor pluggable
plus (SFP+) module uplink slots
C1000-24T-4X-L
24 10/100/1000 Ethernet ports; limited PoE+ ports (PoE budget of 195W); four
10-Gigabit Ethernet SFP+ module uplink slots
C1000-24P-4X-L
24 10/100/1000 PoE+ ports (PoE budget of 370W); four 10-Gigabit Ethernet SFP+
module uplink slots
C1000-24FP-4X-L
48 10/100/1000 Ethernet ports; four 10-Gigabit Ethernet SFP+ module uplink slotsC1000-48T-4X-L
48 10/100/1000 PoE+ ports (PoE budget of 370W); four 10-Gigabit Ethernet SFP+
module uplink slots
C1000-48P-4X-L
48 10/100/1000 PoE+ ports (PoE budget of 740W); four 10-Gigabit Ethernet SFP+
module uplink slots
C1000-48FP-4X-L
Front Panel
This section describes the front panel components of a 24-port and 48-port Cisco Catalyst 1000 switch.
• 24 or 48 downlink ports of one of these types:
• 10/100/1000 Ethernet
• 10/100/1000 PoE+
• Four SFP uplink ports
Four SFP+ uplink ports
• USB Type A connectors
• USB mini-Type B (console) port
• RJ-45 console port
• LEDs
• Reset button
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
2
Product Overview
Front Panel

Figure 1: Front Panel of a 24-Port Cisco Catalyst 1000 PoE Switch
RJ-45 console port5USB Type A port1
24 10/100/1000 PoE+
ports
6Reset button2
SFP module slots7System LED3
USB mini-Type B
(console) port
4
Figure 2: Front Panel of a 48-Port Cisco Catalyst 1000 PoE Switch
USB Type A port5Reset button1
48 10/100/1000 PoE+
ports
6System LED2
SFP module slots7USB mini-Type B
(console) port
3
RJ-45 console port4
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
3
Product Overview
Front Panel

PoE Ports
The ports provide PoE support for devices compliant with IEEE 802.3af and IEEE 802.3at and also provide
PoE support for Cisco IP Phones and Cisco Aironet Access Points. The PoE switch ports are Power Source
equipment (PSE) capable and source power to PD devices connected to the downlink ports. A switch can
source POE power of up to 30W per port.
Depending on the switch model and the number of PoE ports, the maximum switch power output varies. For
the 24-port switch models, the power range is between 195W to 370W. For the 48-port switch models, the
power range is between 180W and 740W. On a per-port basis, you can control whether or not a port
automatically provides power when an IP phone or an access point is connected.
The PoE ports use RJ-45 connectors with Ethernet pinouts. The 10BASE-T, 100BASE-TX, 1000BASE-T
traffic requires Category 5 or Category 5e twisted pair (UTP) cable. The 10BASE-T traffic can use Category
3 or Category 4 UTP cable.
10/100/1000 Ports
The 10/100/1000 ports use RJ-45 connectors with Ethernet pinouts. The 10BASE-T, 100BASE-TX,
1000BASE-T traffic requires Category 5 or Category 5e twisted pair (UTP) cable. The 10BASE-T traffic can
use Category 3 or Category 4 UTP cable.
Console Ports
The console ports connect the switch to a PC running Microsoft Windows or to a terminal server.
• RJ-45 console port (EIA/TIA-232). The RJ-45 console port connection uses an RJ-45-to-DB-9 female
cable.
• USB mini-Type B console port (5-pin connector).
If you use the USB mini-Type B console port, the Cisco Windows USB device driver must be installed on
any PC connected to the console port (for operation with Microsoft Windows). Mac OS X or Linux do not
require special drivers.
The 4-pin mini-Type B connector resembles the 5-pin mini-Type B connectors. They are not compatible. Use
only the 5-pin mini-Type B.
This illustration shows a 5-pin mini-Type B USB port.
Figure 3: USB Mini-Type B Port
With the Cisco Windows USB device driver, you can connect and disconnect the USB cable from the console
port without affecting Windows HyperTerminal operations.
The console output always goes to both the RJ-45 and the USB console connectors, but the console input is
active on only one of the console connectors at any one time. The USB console takes precedence over the
RJ-45 console. When a cable is connected into the USB console port, the RJ-45 console port becomes inactive.
Conversely, when the USB cable is disconnected from the USB console port, the RJ-45 port becomes active.
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
4
Product Overview
PoE Ports

You can use the command-line interface (CLI) to configure an inactivity timeout which reactivates the RJ-45
console if the USB console has been activated and no input activity has occurred on the USB console for a
specified time.
After the USB console deactivates due to inactivity, you cannot use the CLI to reactivate it. Disconnect and
reconnect the USB cable to reactivate the USB console. For information on using the CLI to configure the
USB console interface, see the software guide.
USB Type A Port
The USB Type A port provides access to external USB flash devices (also known as thumb drives or USB
keys).
The port supports Cisco USB flash drives with capacities from 128 MB to 8 GB (USB devices with port
densities of 128 MB, 256 MB, 1 GB, 4 GB, and 8 GB are supported). Cisco IOS software provides standard
file system access to the flash device: read, write, erase, and copy, as well as the ability to format the flash
device with a FAT file system.
It provides you with the ability to automatically upgrade the internal flash with the USB drive's configuration
and image for emergency switch recovery using USB auto-upgrade. This feature checks the internal flash for
a bootable image and configuration and if either image or the configuration is not available, then the USB
drive is checked for boot images and configuration. If the boot image and configuration are available, these
are copied to flash for the reboot.
SFP Module Slots
The switch has four 1G SFP or 10G SFP+ module slots. The SFP and SFP+ modules provide copper or
fiber-optic connections to other devices. These transceiver modules are field replaceable, and provide the
uplink interfaces when installed in an SFP module slot. The SFP modules have LC connectors for fiber-optic
connections or RJ-45 connectors for copper connections. The SFP slots support only SFP modules.
For Cisco SFP modules documentation, including compatibility matrixes, refer to this URL:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html
Table 2: Port mapping for Cisco Catalyst 1000 24-Port Switch models
10-GigabitEthernet ports1-GigabitEthernet ports
TenGigabitEthernet1/0/1GigabitEthernet1/0/25
TenGigabitEthernet1/0/2GigabitEthernet1/0/26
TenGigabitEthernet1/0/3GigabitEthernet1/0/27
TenGigabitEthernet1/0/4GigabitEthernet1/0/28
Table 3: Port mapping for Cisco Catalyst 1000 48-Port Switch models
10-GigabitEthernet ports1-GigabitEthernet ports
TenGigabitEthernet1/0/1GigabitEthernet1/0/49
TenGigabitEthernet1/0/2GigabitEthernet1/0/50
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
5
Product Overview
USB Type A Port

10-GigabitEthernet ports1-GigabitEthernet ports
TenGigabitEthernet1/0/3GigabitEthernet1/0/51
TenGigabitEthernet1/0/4GigabitEthernet1/0/52
If you insert a 10G SFP+ in to a 1G SFP module slot and vice versa, you need to clear the existing configuration
by running the default-interface <interface-number> command on the mapped ports. For more information
about the command, refer to the Software Configuration Guide.
Note
LEDs
You can use the switch system and port LEDs to monitor switch activity and performance.
Figure 4: System LED
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
6
Product Overview
LEDs

Port LEDs2SYST LED (system)1
System LED
System StatusColor
System is not powered on.Off
System is operating normally.Green
System is receiving power but is not operating
properly.
Amber
POST is in progress.Blinking Green
Port LEDs
Physically, there is no amber LED on the device. For all LED-related information of the device, run the show
hardware led command in privileged EXEC mode.
Note
RJ-45 ports and SFP-module slots have port LEDs. These LEDs, as a group or individually, provide information
about the switch and about the individual ports.
DescriptionLED Color
No link or port was administratively shut down.Off
Link present.Green
Activity. Port is sending or receiving data.Blinking Green
Rear Panel
• A security slot
• An AC power connector
• A loop (for the optional power cord retainer)
• Heat sink fins (fanless models only)
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
7
Product Overview
System LED

Figure 5: Rear Panel of a Switch with Fan
An AC power connector3Security Slot1
A loop (for the optional
power cord retainer)
2
Figure 6: Rear Panel of a Fanless Switch
An AC power connector3Security Slot1
Heat sink fins4A loop (for the optional
power cord retainer)
2
Internal Power Supply
All the switches are powered through their internal power supplies. The internal power supply is an autoranging
unit that supports input voltages between 100 and 240 VAC (max of 90V to 264V). The AC frequency range
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
8
Product Overview
Internal Power Supply

of the power supply is 50Hz/60Hz. Plug the AC power cord into the AC power connector and into an AC
power outlet.
Security Slot
The switches have security slots on the rear panel. You can install an optional cable lock, such as the type
that is used to secure a laptop computer, to secure the switch.
Figure 7: Switch Rear Panel
Network Configurations
See the switch software configuration guide for network configuration concepts and examples of using the
switch to create dedicated network segments and interconnecting the segments through Fast Ethernet and
Gigabit Ethernet connections.
Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
9
Product Overview
Security Slot

Cisco Catalyst 1000 Series 24-Port and 48-Port Switch Hardware Installation Guide
10
Product Overview
Network Configurations