Cisco Catalyst 2960-L User manual

Cisco Catalyst 2960-L Switch Getting Started
Guide
Getting Started with the Switch
Getting Started with the Switch
•
About the document
This guide provides instructions for the initial set up of your Cisco Catalyst 2960-L switch. It includes basic
rack-mounting, desk and shelf mounting for the switch, port and module connection procedures, and
troubleshooting information.
Before installing or upgrading the switch, refer to the Cisco Catalyst 2960-L switch Release Notes available
on cisco.com.
Note
Cisco Catalyst 2960-L Switch Getting Started Guide
1

Box Contents
This section lists the contents of the shipping box for an 8-port and 16-port Cisco Catalyst 2960-L switch.
Figure 1: Box Contents of an 8-Port and 16-Port Cisco Catalyst 2960-L Switch
(Optional) Console cable or USB cable78-port or 16-port Cisco Catalyst 2960-L
switch
1
(Optional) Power cord retainer8AC power cord2
(Optional) Magnet tray combo9Four rubber mounting feet (51-0089)3
(Optional) Cable guard10Compliance documentation
(78-100866-01)
4
(Optional) DIN rail mount11Three number-8 screws (48-1689-01)5
Icon legend label (47-103380-01)12Screw template (47-100996-02)6
Cisco Catalyst 2960-L Switch Getting Started Guide
2
Getting Started with the Switch
Box Contents

This section lists the contents of the shipping box for a 24-port and 48-port Cisco Catalyst 2960-L switch.
Figure 2: Box Contents of a 24-Port and 48-Port Cisco Catalyst 2960-L Switch
Four Number-10 Phillips pan-head screws
(48-0627-01)
824-port and 48-port Cisco Catalyst 2960-L
switch
1
Four Number-8 Phillips flat-head screws
(48-2927-01)
9AC power cord2
One black Phillips machine screw
(48-0654-01)
10Four rubber-mounting feet (51-0089)3
(Optional) Console cable or USB cable11Compliance documentation
(78-100866-01)
4
(Optional) Power cord retainer12Two 19-inch mounting brackets5
Icon legend label (47-103380-01)13Cable guide6
Four Number-12 Phillips pan-head screws
(48-0523-01)
7
Cisco Catalyst 2960-L Switch Getting Started Guide
3
Getting Started with the Switch
Box Contents

Installing the Switch
This section describes rack-mounting using 19-inch and 23-inch rack-mounting brackets. For optional bracket
information and alternate mounting procedures, such as installing the switch in a 24-inch rack or on a wall,
and for additional cabling information, see the Hardware Installation Guide on Cisco.com.
Tools and Equipment
Obtain these necessary tools:
•A Number-2 Phillips screwdriver to rack-mount the switch
•Drill with #27 drill bit (0.144-inch [3.7 mm]) for mounting an 8-port and 16-port switch
Installation Guidelines
When determining where to install the switch, verify that these guidelines are met:
•Clearance to the switch's front and rear panel should meet these conditions:
◦Front-panel LEDs can be easily read.
◦Access to ports is sufficient for unrestricted cabling.
◦AC power cord can reach from the AC power outlet to the connector on the switch's rear panel.
•Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting
fixtures. Make sure that the cabling is safely away from other devices that might damage the cables.
•Airflow around the switch and through the vents is unrestricted. To avoid any flow blockage, we strongly
recommend these guidelines:
◦Allow at least 3 in. (7.6 cm) of clearance from the left and the right sides, and the front and rear
of the switch.
◦Allow at least 1.75 in. (4 cm) of clearance from the top cover, if you are installing the switch in
upright position.
◦Allow at least 3 in. (7.6 cm) of clearance from the top cover, if you are installing the switch inverted,
under a table.
◦Allow at least 1 RU of empty rack space above the switch, if you are installing the switch in a rack.
•Temperature around the unit does not exceed 113°F (45°C). If the switch is installed in a closed or
multirack assembly, the temperature around it might be greater than normal room temperature.
•Humidity around the switch does not exceed 95 percent.
•Altitude at the installation site is not greater than 10,000 feet.
•For 10/100/1000 fixed ports, the cable length from a switch to a connected device cannot exceed 328
feet (100 meters).
•Cooling mechanisms, such as fans and blowers in the switch, can draw dust and other particles causing
contaminant build-up inside the chassis, which can result in system malfunction. You must install this
Cisco Catalyst 2960-L Switch Getting Started Guide
4
Getting Started with the Switch
Installing the Switch

equipment in an environment as free from dust and foreign conductive material (such as metal flakes
from construction activities) as is possible.
•None of the switch models can be deployed outside of the wiring closet. These switches can only be
deployed indoors.
Safety Warnings
This section includes the warning statements relating to basic installation. Read this section before you start
the installation procedure.
Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces,
and watches). Metal objects will heat up when connected to power and ground and can cause serious burns
or weld the metal object to the terminals. Statement 43
Warning
Do not stack the chassis on any other equipment. If the chassis falls, it can cause severe bodily injury and
equipment damage. Statement 48
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct
hardware or to follow the correct procedures could result in a hazardous situation to people and damage
to the system. Statement 378
Warning
Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement
1001
Warning
Read the installation instructions before connecting the system to the power source. Statement 1004Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions
to ensure that the system remains stable. The following guidelines are provided to ensure your safety:
Warning
•This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
•When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the
heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing
the unit in the rack.
Statement 1006
Cisco Catalyst 2960-L Switch Getting Started Guide
5
Getting Started with the Switch
Installing the Switch

Class 1 laser product. Statement 1008Warning
Do not stare into the laser beam. Statement 1010Warning
This unit is intended for installation in restricted access areas. A restricted access area can be accessed
only through the use of a special tool, lock and key, or other means of security. Statement 1017
Warning
The plug-socket combination must be accessible at all times, because it serves as the main disconnecting
device. Statement 1019
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021
Warning
A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement
1022
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority
or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning
When installing or replacing the unit, the ground connection must always be made first and disconnected
last. Statement 1046
Warning
To prevent the system from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of: <113°F (45°C). Statement 1047
Warning
Cisco Catalyst 2960-L Switch Getting Started Guide
6
Getting Started with the Switch
Installing the Switch

The maximum operating temperature is 40°C for Catalyst WS-C2960L-16PS-LL switches and 45°C for
all the other switch models.
Note
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams
or view directly with optical instruments. Statement 1051
Warning
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
Warning
Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections
are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such
interconnection methods, unless the exposed metal parts are located within a restricted access location
and users and service people who are authorized within the restricted access location are made aware of
the hazard. A restricted access area can be accessed only through the use of a special tool, lock and key
or other means of security. Statement 1072
Warning
No user-serviceable parts inside. Do not open. Statement 1073Warning
Installation of the equipment must comply with local and national electrical codes. Statement 1074Warning
To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 3 inches (7.6
cm). Statement 1076
Warning
Hot surface. Statement 1079Warning
Desk-Mounting or Shelf-Mounting the Switch
Mounting on a Desk or Shelf Without Mounting Screws
Step 1 Locate the adhesive strip with the rubber feet in the accessory kit.
Step 2 Remove the four rubber feet from the adhesive strip, and attach them to the recessed areas at the bottom of the unit. This
prevents the switch from sliding on the desk or shelf.
We strongly recommend that you attach the rubber feet. Doing so also helps prevent airflow restriction and
overheating.
Note
Cisco Catalyst 2960-L Switch Getting Started Guide
7
Getting Started with the Switch
Installing the Switch

Step 3 Place the switch on the desk or shelf.
Mounting on a Desk or Shelf with Mounting Screws
This procedure is applicable only for 8-port and 16-port switch models.Note
Step 1 Use the screw template to align the mounting screw holes and also as a guide to make sure that you install the screws
into the desk or shelf with proper clearance.
Step 2 Position the screw template on top of the desk or shelf so that the edge that is marked as CABLE SIDE ENTRY faces
the front of the desk or shelf. This ensures that the power cord faces the rear of the desk or shelf after the switch is
installed.
Step 3 Peel the adhesive strip off the bottom of the screw template and attach it to the top of the desk or shelf.
Step 4 Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2-inch (12.7 mm) hole in the two screw template slots.
Step 5 Insert two screws into the slots on the screw template, and tighten them until they touch the top of the screw template.
Figure 3: Attaching the Mounting Screws on to the Screw Template
Desk or shelf3Screw template1
Screws2
Cisco Catalyst 2960-L Switch Getting Started Guide
8
Getting Started with the Switch
Installing the Switch

Step 6 Remove the screw template from the desk or shelf.
Step 7 Place the switch on the mounting screws, and slide it forward until it locks in place.
Figure 4: Mounting the Switch on Top of a Desk or Shelf
Desk or shelf3Slides this way1
Screws2
Rack-Mounting the Switch
Attaching the Rack-Mount Brackets
Attaching the Rack-Mount Brackets to an 8-Port and 16-Port Cisco Catalyst 2960-L Switch
Installing an 8-port and 16-port Cisco Catalyst 2960-L switch in a 19-inch rack requires an optional bracket
kit that is not included with the switch. You can order these kits by contacting your Cisco representative.
Cisco Catalyst 2960-L Switch Getting Started Guide
9
Getting Started with the Switch
Installing the Switch

Use the Phillips flat-head screws that are available with the bracket kit to attach the brackets to the switch.
Figure 5: Attaching 19-Inch Brackets to an 8-Port and 16-Port Cisco Catalyst 2960-L Switch
Switch with 23-inch brackets attached3Switch with 19-inch brackets attached1
Number-8 Phillips flat-head screws2
Cisco Catalyst 2960-L Switch Getting Started Guide
10
Getting Started with the Switch
Installing the Switch