Cisco Catalyst 3560-E Series User manual

GETTING STARTED GUIDE
Catalyst 3560-E Switch Getting Started Guide
1About this Guide
2Taking Out What You Need
3Running Express Setup
4Managing the Switch
5Rack-Mounting
6Connecting to the Switch Ports
7In Case of Difficulty
8Obtaining Documentation and Submitting a Service Request
9Cisco Warranty Terms

2
1 About this Guide
This guide provides instructions on how to use Express Setup to initially configure your Catalyst
switch. Also covered are switch management options, basic rack-mounting procedures, port and
module connection procedures, and troubleshooting help.
For additional installation and configuration information for Catalyst 3560-E switches, see the
Catalyst 3560-E documentation on Cisco.com. For system requirements, important notes, limitations,
open and resolved bugs, and last-minute documentation updates, see the release notes, also on
Cisco.com.
When using the online publications, refer to the documents that match the Cisco IOS software version
running on the switch. The software version is on the Cisco IOS label on the switch rear panel.
For translations of the warnings that appear in this publication, see the Regulatory Compliance and
Safety Information for the Catalyst 3750-E and Catalyst 3560-E Switch that accompanies this guide.
2 Taking Out What You Need
Follow these steps:
1. Unpack and remove the switch and the accessory kit from the shipping box.
2. Return the packing material to the shipping container, and save it for future use.
3. Verify that you have received the items shown on page 3. If any item is missing or damaged,
contact your Cisco representative or reseller for instructions.
Some switch models might include additional items that are not shown on page 3.
4. For switches with the optional 1150-W power supply module (model C3K-PWR-1150WAC),
install the power supply in the switch as described in the installation notes after you rack-mount
the switch.

3
Shipping Box Contents
1Catalyst switch1
1. Catalyst 3560E-48 Power over Ethernet (PoE) switch shown for example. Your switch model might look different.
7Four rubber mounting feet
2Documentation 8Power cord retainer
3AC power cord 9Twelve number-8 Phillips flat-head screws
4Console cable (optional) 10 Four number-12 Phillips machine screws
5Two 19-inch mounting brackets 11 One black Phillips machine screw
6Cable guide 12 Ground lug screw and ring terminal
MODE
SYST
RPS
MASTR
STAT
DUPLX
SPEED
PoE
STACK
49
51
X2-1
X2-2
50
52
37 38 399 40 41 42 43 44 45 46 47 48
37X a
38X 48X
25 26 27 28 29 30 31 32 33 34 35 36
25X 35X
26X 36X
13 14 15 16 17 18 19 20 21 22 23 24
13X 23X
14X 24X
12345678910 11 12
1X 11X
2X 12X
Catalyst 3560-E
SERIES
PoE-48
1
3 4 5
6 7
9
8
10 11 12
207382
2
Product
Documentation
and Compliance

4
3 Running Express Setup
When you first set up the switch, you should use Express Setup to enter the initial IP information.
Doing this enables the switch to connect to local routers and the Internet. You can then access the
switch through the IP address for further configuration.
You need this equipment to set up the switch:
•A PC with Windows 2000 or XP installed
•A web browser (Internet Explorer 5.5, 6.0, Netscape 7.1 or later) with JavaScript enabled
•A straight-through or crossover Category 5 Ethernet cable to connect your PC to the switch
Disable any pop-up blockers or proxy settings in your browser software and any wireless client
running on your PC.
As an example, the Express Setup illustrations show the Catalyst 3560E-48 PoE switch. You can run
Express Setup on all Catalyst 3560-E switch models.
To run Express Setup:
Step 1 Make sure that nothing is connected to the
switch.
During Express Setup, the switch acts as a
DHCP server. If your PC has a static IP
address, change your PC settings before you
begin to temporarily use DHCP.
Step 2 Power the switch.
For AC-powered switches, connect the AC
power cord to the switch power supply and
to a grounded AC outlet.
For DC-powered switches, see the wiring
instructions in the hardware installation
guide on Cisco.com.
Step 3 When the switch powers on, it begins the power-on self-test (POST). During POST, the
LEDs blink while tests verify that the switch functions properly.
Wait for the switch to complete POST, which can take several minutes.
Step 4 Verify that POST has completed by confirming that the SYST LED remains green. If the
switch fails POST, the SYST LED turns amber. See the “In Case of Difficulty” section on
page 20 if your switch fails POST.
MODE
SYST
RPS
MASTR
STAT
DUPLX
SPEED
PoE
STACK
49
51
X2-1
X2-2
50
52
37 38 399 40 41 42 43 44 45 46 47 48
37X47X
38X48X
25 26 27 28 29 30 31 32 33 34 35 36
25X35X
26X36X
13 14 15 16 17 18 19 20 21 22 23 24
13X23X
14X 24X
12345678910 11 12
1X11X
2X12X
Catalyst3560-E
SERIES
PoE-48
ACOKPSOK
100-240V~
1.0-5A
50-60HZ

5
Step 5 Press and hold the Mode button for
3 seconds. When all of the LEDs above the
Mode button turn green, release the Mode
button.
Step 6 If the LEDs above the Mode button blink after you press the button, release it. Blinking
LEDs mean that the switch is already configured and cannot go into Express Setup mode.
For more information, see the “Resetting the Switch” section on page 21.
Step 7 Verify that the switch is in Express Setup mode. Make sure that all LEDs above the Mode
button are green. (On some switch models, the RPS LED remains off.)
Step 8 Connect a Category 5 Ethernet cable to one
of these locations:
•Any 10/100/1000 Ethernet port on the
switch front panel (for switches with
front-panel Ethernet ports).
•The Ethernet management port on the
switch rear panel.
Connect the other end of the cable to the
Ethernet port on your PC.
Step 9 Verify that the LEDs on both Ethernet ports are green.
Wait 30 seconds.
Step 10 Launch a web browser on your PC. Enter the
IP address 10.0.0.1 in the web browser, and
press Enter.
Step 11 The switch prompts you for the default switch password. Enter the default password, cisco.
Note The switch ignores text in the username field.
MODE
SYST
RPS
MASTR
STAT
DUPLX
SPEED
PoE
STACK
49
51
X2-1
X2-2
50
52
37 38 399 40 41 42 43 44 45 46 47 48
37X47X
38X48X
25 26 27 28 29 30 31 32 33 34 35 36
25X35X
26X36X
13 14 15 16 17 18 19 20 21 22 23 24
13X23X
14X24X
12345678910 11 12
1X11X
2X12X
Catalyst3560-E
SERIES
PoE-48
MODE
SYST
RPS
STAT
DUPLX
SPEED
PoE
MODE
SYST
RPS
MASTR
STAT
DUPLX
SPEED
PoE
STACK
49
51
X2-1
X2-2
50
52
3738399404142434445464748
37X47X
38X48X
252627282930313233343536
25X35X
26X36X
131415161718192021222324
13X23X
14X24X
123456789101112
1X11X
2X12X
Catalyst3560-E
SERIES
PoE-48

6
Step 12 The Express Setup Basic Settings page appears. If it does not appear, see the “In Case of
Difficulty” section on page 20.
Step 13 Enter this information in the Network Settings fields:
•In the Management Interface (VLAN ID) field, the default is 1. Enter a new VLAN ID
only if you want to change the management interface through which you manage the
switch. The VLAN ID range is 1 to 4094.
•In the IP Address field, enter the IP address of the switch. In the Subnet Mask field, click
the drop-down arrow, and select a Subnet Mask.
•In the Default Gateway field, enter the IP address for the default gateway (router).
•Enter your password in the Switch Password field. The password can be from 1 to 25
alphanumeric characters, can start with a number, is case sensitive, allows embedded
spaces, but does not allow spaces at the beginning or end. In the Confirm Switch
Password field, enter your password again.
Note You must change the password from the default password, cisco.
Step 14 (Optional) Enter this information in the Ethernet Management Port Settings fields:
In the IP Address field, enter the IP address of the Ethernet management port. In the Subnet
Mask field, click the drop-down arrow, and select a Subnet Mask.

7
Step 15 (Optional) You can enter the Optional Settings information now or enter it later by using
the device manager interface:
•In the Host Name field, enter a name for the switch. The host name is limited to 31
characters; embedded spaces are not allowed.
•Enter the date, time, and time zone information in the System Date, System Time, and
Time Zone fields. Click Enable to enable daylight saving time.
Step 16 (Optional) You can select the Advanced Settings tab on the Express Setup window and enter
the advanced settings now or enter them later by using the device manager interface.

8
Step 17 (Optional) Enter this information in the Advanced Setting fields:
•In the Telnet Access field, click Enable if you are going to use Telnet to manage the
switch by using the command-line interface (CLI). If you enable Telnet access, you must
enter a Telnet password.
•In the Telnet Password field, enter a password. The Telnet password can be from 1 to
25 alphanumeric characters, is case sensitive, allows embedded spaces, but does not
allow spaces at the beginning or end. In the Confirm Telnet Password field, re-enter the
Telnet password.
•In the SNMP field, click Enable to enable Simple Network Management Protocol
(SNMP). Enable SNMP only if you plan to manage switches by using CiscoWorks 2000
or another SNMP-based network-management system.
•If you enable SNMP, you must enter a community string in the SNMP Read Community
field, the SNMP Write Community field, or both. SNMP community strings
authenticate access to MIB objects. Embedded spaces are not allowed in SNMP
community strings. When you set the SNMP read community, you can access SNMP
information, but you cannot change it. When you set the SNMP write community, you
can both access and change SNMP information.
•In the System Contact and System Location fields, enter a contact name and the wiring
closet, floor, or building where the switch is located.
Step 18 (Optional) You can enable IPv6 on the switch in the Advanced Settings window. In the
Enable IPv6 field, click Enable.
Note Enabling IPv6 restarts the switch when you complete Express Setup.
Step 19 To complete Express Setup, click Submit in the Network Settings or the Advanced Settings
window to save your settings. Click Cancel to clear your settings.
When you click Submit, the switch is configured and exits Express Setup mode. The PC
displays a warning message and then tries to connect with the new switch IP address. If you
configured the switch with an IP address that is in a different subnet from the PC,
connectivity between the PC and the switch is lost. If you enabled IPv6, the switch restarts.
Step 20 Disconnect the switch from the PC, and install the switch in your production network. See
the “Managing the Switch” section on page 9 for information about configuring and
managing the switch.
If you need to rerun Express Setup, see the “Resetting the Switch” section on page 21.

9
Refreshing the PC IP Address
After you complete Express Setup, you should refresh the PC IP address:
•For a dynamically assigned IP address, disconnect the PC from the switch, and reconnect the PC
to the network. The network DHCP server assigns a new IP address to the PC.
•For a statically assigned IP address, change it to the previously configured IP address.
4 Managing the Switch
After you complete Express Setup and install the switch in your network, use the device manager or
other management options described in this section for further configuration.
Using the Device Manager
The simplest way to manage the switch is by using the device manager that is in the switch memory.
This is a web interface that offers quick configuration and monitoring. You can access the device
manager from anywhere in your network through a web browser.
Follow these steps:
1. Launch a web browser on your PC or workstation.
2. Enter the switch IP address in the web browser, and press Enter. The device manager page appears.
3. Use the device manager to perform basic switch configuration and monitoring. Refer to the device
manager online help for more information.
4. For more advanced configuration, download and run the Cisco Network Assistant, which is
described in the next section.
Downloading Cisco Network Assistant
Cisco Network Assistant is a software program that you download from Cisco.com and run on
your PC. It offers advanced options for configuring and monitoring multiple devices, including
switches, switch clusters, routers, and access points. Network Assistant is free—there is no charge to
download, install, or use it.
Follow these steps:
1. Go to this Web address: http://www.cisco.com/go/NetworkAssistant.
You must be a registered Cisco.com user, but you need no other access privileges.
2. Find the Network Assistant installer.

10
3. Download the Network Assistant installer, and run it. (You can run it directly from the Web if
your browser offers this choice.)
4. When you run the installer, follow the displayed instructions. In the final panel, click Finish to
complete the Network Assistant installation.
Refer to the Network Assistant online help and the getting started guide for more information.
Command-Line Interface
You can enter Cisco IOS commands and parameters through the CLI. Access the CLI by connecting
your PC directly to the switch console port or to the Ethernet management port.
Using the switch console port:
Follow these steps:
1. Connect the supplied RJ-45-to-DB-9 adapter cable to the standard 9-pin serial port on the PC.
Connect the other end of the cable to the console port on the switch.
2. Start a terminal-emulation program on the PC.
3. Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit,
and no flow control.
4. Use the CLI to enter commands to configure the switch. See the software configuration guide and
the command reference for more information.
Using the switch Ethernet management port:
Follow these steps:
1. Connect a Category 5 Ethernet cable to the PC Ethernet port. Connect the other end of the cable
to the Ethernet management port on the switch rear panel.
2. Start a Telnet session on the PC.
3. Enter the switch IP address that you assigned by using Express Setup.
4. Use the CLI to enter commands to configure the switch. See the software configuration guide and
the command reference for more information.