Cisco Nexus 9504 Manual

Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
First Published: 2014-11-10
Last Modified: 2021-02-01
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS REFERENCED IN THIS DOCUMENTATION ARE SUBJECT TO CHANGE WITHOUT NOTICE.
EXCEPT AS MAY OTHERWISE BE AGREED BY CISCO IN WRITING, ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS DOCUMENTATION ARE
PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED.
The Cisco End User License Agreement and any supplemental license terms govern your use of any Cisco software, including this product documentation, and are located at:
http://www.cisco.com/go/softwareterms.Cisco product warranty information is available at http://www.cisco.com/go/warranty. US Federal Communications Commission Notices are found
here http://www.cisco.com/c/en/us/products/us-fcc-notice.html.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any products and features described herein as in development or available at a future date remain in varying stages of development and will be offered on a when-and if-available basis. Any
such product or feature roadmaps are subject to change at the sole discretion of Cisco and Cisco will have no liability for delay in the delivery or failure to deliver any products or feature
roadmap items that may be set forth in this document.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based
on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language
that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com
go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any
other company. (1721R)
©2014–2021 Cisco Systems, Inc. All rights reserved.

CONTENTS
Trademarks ?
Preface vii
PREFACE
Audience vii
Documentation Conventions vii
Related Documentation viii
Documentation Feedback x
Obtaining Documentation and Submitting a Service Request x
Overview 1
CHAPTER 1
Overview 1
Preparing the Site 7
CHAPTER 2
Temperature Requirements 7
Humidity Requirements 7
Altitude Requirements 7
Dust and Particulate Requirements 8
Minimizing Electromagnetic and Radio Frequency Interference 8
Shock and Vibration Requirements 9
Grounding Requirements 9
Planning for Power Requirements 9
Rack and Cabinet Requirements 14
Clearance Requirements 15
Installing a Chassis 17
CHAPTER 3
Installing a Rack or Cabinet 17
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
iii

Inspecting the New Switch 18
Installing the Bottom-Support Rails 19
Installing a Chassis in a Rack or Cabinet 22
Grounding the Chassis 25
Starting Up the Switch 27
Connecting a 3-kW AC Power Supply to an AC Power Source 28
Connecting a 3-kW Universal AC/DC Power Supply to an AC Power Source 28
Connecting a 3-kW Universal AC/DC Power Supply to a DC Power Source 28
Connecting a 3-kW DC Power Supply to a DC Power Source 29
Connecting the Switch to the ACI Fabric 33
CHAPTER 4
ACI Fabric Topology 33
Preparing to Connect to Other Devices 34
Connecting Leaf Switches to APICs 35
Connecting Leaf Switches to Spine Switches 37
Installing a Gigabit Ethernet module (GEM) 38
Migration of Nodes From a First Generation Switch to a Second Generation Switch 38
Setting Up an Optional Console Interface 40
Setting Up an Optional Management Connection 41
Optic Transceiver Removal Using the Optics Extraction Tool 41
Maintaining Transceivers and Optical Cables 43
Replacing or Installing Modules, Fan Trays, and Power Supplies 45
CHAPTER 5
Preventing Electrostatic Damage 45
Installing or Replacing a Supervisor Module 45
Upgrading a Supervisor Module 49
Installing or Replacing a System Controller Module 49
Installing or Replacing a Line Card 52
Installing and Removing a Blank Line Card 55
Replacing a Fan Tray 57
Removing a Fan Tray 57
Installing a Fan Tray 58
Replacing a Fabric Module 59
Removing a Fabric Module 60
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
iv
Contents

Installing a Fabric Module 63
Installing or Replacing Power Supplies 65
Installing or Replacing a 3-kW AC Power Supply 66
Installing or Replacing a 3-kW Universal AC/DC Power Supply 69
Installing or Replacing a 3.15-kW Dual Input Universal AC/DC Power Supply 72
Installing or Replacing a 3-kW DC Power Supply 74
System Specifications 79
APPENDIX A
Environmental Specifications 79
Switch Dimensions 79
Weights for the Chassis, Modules, Fan Trays, and Power Supplies 80
Power Specifications 81
Power Requirements for Switch Modules 81
Maximum Power Available to the Switch 82
Power Supply Specifications 82
3000-W AC Power Supply Specifications 82
3000-W Universal AC/DC Power Supply Specifications 82
3000-W Dual Input Universal AC/DC Power Supply Specifications 83
Power Cable Specifications 83
3-kW AC Power Cable Specifications 83
3-kW Universal AC/DC and 3-kW Dual Input Universal AC/DC Power Cable Specifications 87
3-kW DC Power Supply Power Cord Specifications 91
LEDs 93
APPENDIX B
Chassis LEDs 93
System Controller LEDs 94
Supervisor Module LEDs 94
Fan Tray LEDs 95
Fabric Module LEDs 96
Line Card LEDs 96
Power Supply LEDs 97
Additional Kits 99
APPENDIX C
Accessory Kit 99
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
v
Contents

Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
vi
Contents

Preface
•Audience, on page vii
•Documentation Conventions, on page vii
•Related Documentation, on page viii
•Documentation Feedback, on page x
•Obtaining Documentation and Submitting a Service Request , on page x
Audience
This publication is for hardware installers and network administrators who install, configure, and maintain
Cisco Nexus switches.
Documentation Conventions
Command descriptions use the following conventions:
DescriptionConvention
Bold text indicates the commands and keywords that you enter literally
as shown.
bold
Italic text indicates arguments for which the user supplies the values.Italic
Square brackets enclose an optional element (keyword or argument).[x]
Square brackets enclosing keywords or arguments separated by a vertical
bar indicate an optional choice.
[x | y]
Braces enclosing keywords or arguments separated by a vertical bar
indicate a required choice.
{x | y}
Nested set of square brackets or braces indicate optional or required
choices within optional or required elements. Braces and a vertical bar
within square brackets indicate a required choice within an optional
element.
[x {y | z}]
Indicates a variable for which you supply values, in context where italics
cannot be used.
variable
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
vii

DescriptionConvention
A nonquoted set of characters. Do not use quotation marks around the
string or the string will include the quotation marks.
string
Examples use the following conventions:
DescriptionConvention
Terminal sessions and information the switch displays are in screen font.screen font
Information you must enter is in boldface screen font.boldface screen font
Arguments for which you supply values are in italic screen font.italic screen font
Nonprinting characters, such as passwords, are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning of a line
of code indicates a comment line.
!, #
Related Documentation
The Application Centric Infrastructure documentation set includes the following documents that are available
on Cisco.com at the following URL:
https://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/tsd-products-support-series-home.html.
Web-Based Documentation
•Cisco APIC Management Information Mode Reference
•Cisco APIC Online Help Reference
•Cisco APIC Python SDK Reference
•Cisco ACI Compatibility Tool
•Cisco ACI MIB Support List
Downloadable Documentation
•Knowledge Base Articles (KB Articles)are available at the following URL:
https://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/products-configuration-examples-list.html
•Cisco Application Centric Infrastructure Controller Release Notes
•Cisco Application Centric Infrastructure Fundamentals Guide
•Cisco APIC Getting Started Guide
•Cisco ACI Virtualization Guide
•Cisco APIC REST API User Guide
•Cisco APIC Command Line Interface User Guide
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
viii
Preface
Related Documentation

•Cisco APIC Faults, Events, and System Messages Management Guide
•Cisco ACI System Messages Reference Guide
•Cisco APIC Layer 4 to Layer 7 Services Deployment Guide
•Cisco APIC Layer 4 to Layer 7 Device Package Development Guide
•Cisco APIC Layer 4 to Layer 7 Device Package Test Guide
•Cisco ACI Firmware Management Guide
•Cisco ACI Troubleshooting Guide
•Cisco ACI Switch Command Reference, NX-OS Release 11.0
•Cisco Verified Scalability Guide for Cisco ACI
•Cisco ACI MIB Quick Reference
•Cisco Nexus CLI to Cisco APIC Mapping Guide
•Application Centric Inftrastructure Fabric Hardware Installation Guide
•Cisco NX-OS Release Notes for Cisco Nexus 9000 Series ACI-Mode Switches
•Cisco Nexus 9000 Series ACI Mode Licensing Guide
•Cisco Nexus 93108TX-EX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 93108TX-FX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 93120TX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 93128TX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 93180LC-EX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 93180YC-EX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 93180YC-FX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 9332PQ ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 9336PQ ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 9372PX and 9372PX-E ACI-Mode Switches Hardware Installation Guide
•Cisco Nexus 9372TX and 9372TX-E ACI-Mode Switches Hardware Installation Guide
•Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 9396TX ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 9508 ACI-Mode Switch Hardware Installation Guide
•Cisco Nexus 9516 ACI-Mode Switch Hardware Installation Guide
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
ix
Preface
Preface

Cisco Application Centric Infrastructure (ACI) Simulator Documentation
The following Cisco ACI Simulator documentation is available at
https://www.cisco.com/c/en/us/support/cloud-systems-management/application-centric-infrastructure-simulator/tsd-products-support-series-home.html.
•Cisco ACI Simulator Release Notes
•Cisco ACI Simulator Installation Guide
•Cisco ACI Simulator Getting Started Guide
Cisco Nexus 9000 Series Switches Documentation
The Cisco Nexus 9000 Series Switches documentation is available at
https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/tsd-products-support-series-home.html.
Cisco Application Virtual Switch Documentation
The Cisco Application Virtual Switch (AVS) documentation is available at
https://www.cisco.com/c/en/us/support/switches/application-virtual-switch/tsd-products-support-series-home.html.
Documentation Feedback
To provide technical feedback on this document, or to report an error or omission, please send your comments
to [email protected]. We appreciate your feedback.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service
request, and gathering additional information, see What's New in Cisco Product Documentation, at:
https://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
Subscribe to What's New in Cisco Product Documentation, which lists all new and revised Cisco technical
documentation as an RSS feed and delivers content directly to your desktop using a reader application. The
RSS feeds are a free service.
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
x
Preface
Documentation Feedback

CHAPTER 1
Overview
•Overview, on page 1
Overview
This switch chassis includes the following modules:
• Supervisor modules (one or two)—one of the following types in slots SUP 1 and SUP 2 (numbered from
left to right on the chassis)
• System controllers (two) (N9K-SC-A) in slots SC 1 and SC 2 (Modules 29 and 30 in reports) (numbered
from left to right on the chassis)
• Line cards (up to four) in slots LC 1 to LC 4 (Modules 1 through 4 in reports) (numbered from top to
bottom on the chassis) supported by the same type of fabric module
For compatibility information, please refer to the Line Card and Fabric Module Compatibility data sheets.
Do not mix ACI-mode line cards with NX-OS mode line cards in the same
switch.
Note
• Fabric modules in slots FM 1 to FM 6 (Modules 21 through 26 in reports) (numbered from left to right
on the chassis)
See the following table for the required fabric module types and quantities required for maximum
bandwidth.
Table 1: Supported Fabric Modules and Line Cards
Supported Line CardsFabric Modules
Required for
Maximum
Bandwidth
Fabric Module
N9K-X9736PQ6N9K-C9504-FM
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
1

Supported Line CardsFabric Modules
Required for
Maximum
Bandwidth
Fabric Module
N9K-X9732C-EX
N9K-X9736C-FX
N9K-X9736Q-FX
4
5
5
N9K-C9504-FM-E
N9K-X9716D-GX4N9K-C9504-FM-G1
1Note that -G fabric modules require the N9K-C9504-FAN2 fan trays for operation.
See the following table for information about line card to fabric module, line card to line card and
fabric module to fabric module compatibility when implementing the FM-25 feature.
Table 2: FM-25 Feature Support Matrix for Cisco Nexus 9500 Platform line cards and fabric modules
Line cards
X9716D-GXX9736C-FXX9732C-EX
X9736Q-FXX9736PQ
Fabric modules
NoNoNoNo
YesC9504-FM
NoYesNoYesNoC9504-FM-E
NoYesNoYesNoC9504-FM-G
The fabric modules must be installed in specific slots as follows (installing
fabric modules in other slots can cause a module mismatch condition):
• For three modules, they must be in slots FM 2, FM 4, and FM 6
• For four modules, they must be in slots FM2, FM 3, FM 4, and FM 6
• For five modules, they can be in slots FM 1, FM 2, FM 3, FM 4, and
FM 6. Alternatively, they can be in Slots FM 2, FM 3, FM 4, FM 5,
and FM 6.
• For five FM-E or FM-E2 modules, they must be in Slots FM 2, FM 3,
FM 4, FM 5, and FM 6
• For six modules, they are in slots FM 1, FM 2, FM 3, FM 4, FM 5,
and FM 6
Note
All of the fabric modules in a modular switch must be of the same type.
Note
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
2
Overview
Overview

When using FM-G fabric modules, any empty slots should be filled with
FAN-PWR modules (N9K-C9504-FAN-PWR)
Note
When using N9K-C9504-FM or N9K-C9504-FM-E fabric modules, any
empty slots should be filled with N9K-C9504-FM-CV.
Note
For more information about Line card and fabric module compatibility, see
the Cisco Nexus 9500 Platform Line Cards and Fabric Modules Data Sheet
Note
• Fan trays (three) (N9K-C9504-FAN) or (N9k-9504-FAN2) in slots FAN 1 to FAN 3 (Modules 41 to 43
in reports) (numbered from left to right on the chassis)
• Power supplies (up to two with the combined power mode, up to three with n+1 power redundancy mode,
or up to four with the n+npower redundancy mode) in slots PS 1 to PS 4 (Modules 33 to 36 in reports)
(numbered from left to right on the chassis)
• Cisco Nexus 9500 Series 3-kW AC power supply (N9K-PAC-3000W-B)
• Cisco Nexus 9500 Series 3-kW Universal AC/DC power supply (N9K-PUV-3000W-B)
• Cisco Nexus 9500 Series 3.15-kW Dual Input Universal AC/DC power supply
(N9K-PUV2-3000W-B)
• Cisco Nexus 9500 Series 3-kW (-48 V) DC power supply (N9K-PDC-3000W-B)
The switch can be powered by a mix of AC, DC, HVAC/HVDC power
sources.
Note
All chassis slots are numbered from left to right or from top to bottom.
Note
The following figure shows the hardware features seen from the front of the chassis.
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
3
Overview
Overview

3-kW AC, Universal
AC/DC, or DC power
supplies (AC power
supplies shown).
42 vertical mounting
brackets used to mount
the chassis onto a rack
1
Chassis LEDs5Line cards (up to 4)2
Chassis handles (used
only for positioning the
chassis on the bottom
support rails—do not use
these handles for lifting
the chassis)
6Supervisor modules (1 or
2)
3
The following figure shows the hardware features seen from the rear of the chassis (one fan tray has been
removed to show the fabric modules behind the fan trays).
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
4
Overview
Overview

Grounding pad4Fan trays (3—left fan tray
not shown in order to
display the fabric modules
located behind the fan
trays)
1
Chassis handles (used
only for positioning the
chassis on the bottom
support rails—do not use
these handles for lifting
the filled chassis)
5Fabric modules (up to 6
with up to 2 fabric
modules behind each fan
tray)
2
System controllers (2)3
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
5
Overview
Overview

Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
6
Overview
Overview

CHAPTER 2
Preparing the Site
•Temperature Requirements, on page 7
•Humidity Requirements, on page 7
•Altitude Requirements, on page 7
•Dust and Particulate Requirements, on page 8
•Minimizing Electromagnetic and Radio Frequency Interference, on page 8
•Shock and Vibration Requirements, on page 9
•Grounding Requirements, on page 9
•Planning for Power Requirements, on page 9
•Rack and Cabinet Requirements, on page 14
•Clearance Requirements, on page 15
Temperature Requirements
The switch requires an operating temperature of 32 to 104 degrees Fahrenheit (0 to 40 degrees Celsius). If
the switch is not operating, the temperature must be between –40 to 158 degrees Fahrenheit (–40 to 70 degrees
Celsius).
Humidity Requirements
Buildings in which the climate is controlled by air-conditioning in the warmer months and by heat during the
colder months usually maintain an acceptable level of humidity for the switch equipment. However, if the
switch is located in an unusually humid location, use a dehumidifier to maintain the humidity within an
acceptable range.
Altitude Requirements
Altitude rating is based on power supply installed; see critical components list in the system CB report for
altitude rating.
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
7

Dust and Particulate Requirements
Exhaust fans cool power supplies and system fans cool switches by drawing in air and exhausting air out
through various openings in the chassis. However, fans also ingest dust and other particles, causing contaminant
buildup in the switch and increased internal chassis temperature. Dust and particles can act as insulators and
interfere with the mechanical components in the switch. A clean operating environment can greatly reduce
the negative effects of dust and other particles.
In addition to keeping your environment free of dust and particles, follow these precautions to avoid
contamination of your switch:
• Do not permit smoking near the switch.
• Do not permit food or drink near the switch.
Minimizing Electromagnetic and Radio Frequency Interference
Electromagnetic interference (EMI) and radio frequency interference (RFI) from the switch can adversely
affect other devices, such as radio and television (TV) receivers. Radio frequencies that emanate from the
switch can also interfere with cordless and low-power telephones. Conversely, RFI from high-power telephones
can cause spurious characters to appear on the switch monitor.
RFI is defined as any EMI with a frequency above 10 kHz. This type of interference can travel from the switch
to other devices through the power cable and power source or through the air as transmitted radio waves. The
Federal Communications Commission (FCC) publishes specific regulations to limit the amount of EMI and
RFI that are emitted by computing equipment. Each switch meets these FCC regulations.
To reduce the possibility of EMI and RFI, follow these guidelines:
• Cover all open expansion slots with a blank filler plate.
• Always use shielded cables with metal connector shells for attaching peripherals to the switch.
When wires are run for any significant distance in an electromagnetic field, interference can occur to the
signals on the wires with the following implications:
• Bad wiring can result in radio interference emanating from the plant wiring.
• Strong EMI, especially when it is caused by lightning or radio transmitters, can destroy the signal drivers
and receivers in the chassis and even create an electrical hazard by conducting power surges through
lines into equipment.
To predict and prevent strong EMI, you need to consult experts in radio frequency interference (RFI).
Note
The wiring is unlikely to emit radio interference if you use a twisted-pair cable with a good distribution of
grounding conductors. If you exceed the recommended distances, use a high-quality twisted-pair cable with
one ground conductor for each data signal when applicable.
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
8
Preparing the Site
Dust and Particulate Requirements

If the wires exceed the recommended distances, or if wires pass between buildings, give special
consideration to the effect of a lightning strike in your vicinity. The electromagnetic pulse that is caused
by lightning or other high-energy phenomena can easily couple enough energy into unshielded conductors
to destroy electronic switches. You will want to consult experts in electrical surge suppression and
shielding if you had similar problems in the past.
Caution
Shock and Vibration Requirements
The switch has been shock- and vibration-tested for operating ranges, handling, and earthquake standards.
Grounding Requirements
The switch is sensitive to variations in voltage that is supplied by the power sources. Overvoltage, undervoltage,
and transients (or spikes) can erase data from memory or cause components to fail. To protect against these
types of problems, ensure that there is an earth-ground connection for the switch. You can connect the grounding
pad on the switch either directly to the earth-ground connection or to a fully bonded and grounded rack.
When you properly install the chassis in a grounded rack, the switch is grounded because it has a metal-to-metal
connection to the rack. Alternatively, you can ground the chassis by using a customer-supplied grounding
cable that meets your local and national installation requirements. For U.S. installations, we recommend
6-AWG wire. Connect your grounding cable to the chassis with a grounding lug (provided in the switch
accessory kit) and to the facility ground.
You automatically ground AC power supplies when you connect them to AC power sources. For DC
power supplies, you must connect a grounding wire when wiring the power supply to the DC power
source.
Note
An electrical conducting path shall exist between the product chassis and the metal surface of the
enclosure or rack in which it is mounted or to a grounding conductor. Electrical continuity shall be
provided by using thread-forming type mounting screws that remove any paint or non-conductive
coatings and establish a metal-to-metal contact. Any paint or other non-conductive coatings shall be
removed on the surfaces between the mounting hardware and the enclosure or rack. The surfaces shall
be cleaned and an antioxidant applied before installation.
Note
Planning for Power Requirements
To plan for the power requirements of a switch, you must determine each of the following:
• Power requirements for all the switch components
• Minimum number of power supplies required to power the components that are installed in the switch.
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
9
Preparing the Site
Shock and Vibration Requirements

• Power mode to use and the number of extra power supplies required for that mode.
Ensure that the circuit that is used for the switch is dedicated to the switch to minimize the possibility of circuit
failure.
Calculate the power that is required for operations (available power) and redundancy (reserve power), then
you can plan for the required number of input power receptacles. The power receptacles will be within reach
of the switch location.
Step 1 Determine the power requirement for the modules in the switch by summing the maximum wattage for each installed
module, see the following table.
MaximumTypicalComponent
——Supervisor modules
80 W69 WSupervisor A (N9K-SUP-A)–
80 W69 WSupervisor A+ (N9K-SUP-A+)–
90 W75 WSupervisor B (N9K-SUP-B)–
80 W75 WSupervisor B+ (N9K-SUP-B+)–
——System Controller Modules
25 W14 WSystem Controller (N9K-SC-A)–
131 W95 WLine cards that are supported by N9K-C9504-FM fabric modules
211 W197 W36-port 40-Gigabit Ethernet QSFP+ line cards (N9K-X9736PQ)–
313 W234 WLine cards that are supported by N9K-C9504-FM-E fabric modules
720 W430 W32-port 100-Gigabit Ethernet QSFP28 line card (N9K-X9732C-EX)–
900 W607 W36-port 100-Gigabit Ethernet QSFP28 line card (N9K-X9736C-FX)–
684 W571 W36-port 40-Gigabit Ethernet QSFP28 line card (N9K-X9736Q-FX)–
504 W270 WLine cards that are supported by N9K-C9504-FM-G fabric modules
1680 W650 W16-port 400-Gigabit Ethernet QSFP-DD line card (N9K-X9716D-GX)–
——Fan Trays
129 W95 W(N9K-C9504-FAN)–
600 W105 W(N9K-C9504-FAN2)–
For example, to determine the maximum amount of power that your fully loaded switch consumes, add the maximum
power consumption of two supervisor A modules (2 x 80 W = 160 W), two system controllers (2 x 25 W = 50 W), four
36-port 40-Gigabit line cards (4 x 211 W = 844 W), six fabric modules (6 x 131 W = 786 W), and three fan trays (3 x
150 W = 450 W). The total is 2290 W.
Cisco Nexus 9504 ACI-Mode Switch Hardware Installation Guide
10
Preparing the Site
Planning for Power Requirements