Cisco 3750G - Catalyst Integrated Wireless LAN... User manual

Getting Started
Guide
Catalyst 3750G Integrated Wireless LAN Controller Switch
Getting Started Guide
INCLUDING LICENSE AND WARRANTY
1About this Guide
2Taking Out What You Need
3Running Express Setup
4Managing the Switch
5Preparing the Wireless LAN Controller for Operation
6Planning Switch Stacks
7Rack-Mounting
8In Case of Difficulty
9Obtaining Documentation
10 Documentation Feedback

2
11 Cisco Product Security Overview
12 Obtaining Technical Assistance
13 Obtaining Additional Publications and Information
14 Cisco Limited Lifetime Hardware Warranty Terms
1 About this Guide
This guide provides instructions on how to use Express Setup to initially configure your
Catalyst 3750G Integrated Wireless LAN Controller switch. It also covers switch management
options, the configuration procedures for the controller, basic rack-mounting procedures, stacking,
port and module connections, power connection procedures, and any troubleshooting help.
The Catalyst 3750G Integrated Wireless LAN Controller switch has an integrated Cisco wireless LAN
controller that can support Cisco Lightweight Access Points. The switch also has two internal Gigabit
Ethernet ports (ports 27 and 28) that connect the switch and the controller. The integrated wireless
LAN controller centralizes and simplifies network management of a wireless LAN. It collapses large
numbers of managed lightweight access points and client devices into a single unified system.
For additional installation and configuration information for wireless LAN controller switches, see the
Catalyst 3750 documentation on Cisco.com. For more information on the controller, see the Cisco
Wireless LAN Controller Configuration Guide, Release 4.0 or later on Cisco.com. For system
requirements, important notes, limitations, open and resolved caveats, and last-minute documentation
updates, see the release notes, also on Cisco.com.
When using the online publications, refer to the documents that match the Cisco IOS software version
running on the switch. The software version is on the Cisco IOS label on the switch rear panel.
For translations of the warnings that appear in this publication, see the Regulatory Compliance and
Safety Information for the Catalyst 3750 Switch that accompanies this guide.
2 Taking Out What You Need
Follow these steps:
1. Unpack and remove the switch and the accessory kit from the shipping box.
2. Return the packing material to the shipping container, and save it for future use.
3. Verify that you have received the items shown on page 3. If any item is missing or damaged,
contact your Cisco representative or reseller for instructions.
Note If you do not specify the length of the StackWise cable, the 0.5-meter cable is supplied.

3
Shipping Box Contents
Catalyst 3750G
SERIES
PoE-24
Wireless LANController
SYST
RPS
MASTR
STAT
DUPLX
SPEED
STACK
PoE
1X
2X
11X
12X
123456789101112
13X
14X
23X
24X
131415161718192021222324
25 26
Regulatory Compliance
and Safety Information
for the
Catalyst 3750 Switch
Catalyst 3750G
Integrated Wireless
LAN Controller Switch
Getting Started Guide
Cisco
Product Ownership
Registration card
Catalyst 3750G
Integrated Wireless LAN
Controller switch
Console cable
Two 19-inch
mounting brackets
Four number-12 Phillips machine screws
Four number-8 Phillips truss-head screws
Six number-8 Phillips flat-head screws
Four rubber mounting feet
AC power cord
Connector cover for redundant
power system (RPS)
Two number-4 pan-head screws
Cable guide
One black Phillips machine screw
Documentation
0.5-meter, 1-meter or 3-meter
StackWise cable

4
Equipment that You Supply to Run Express Setup
You need to supply this equipment to run Express Setup:
•PC
•Ethernet (Category 5) straight-through cable (as shown)
3 Running Express Setup
When you first set up the switch, you should use Express Setup to enter the initial IP information.
Doing this enables the switch to connect to local routers and the Internet. You can then access the
switch through the IP address for further configuration.
To run Express Setup:
Step 1 Verify that no devices are connected to the switch. During Express Setup, the switch acts
as a DHCP server. If your PC has a static IP address, before you begin, change your PC
settings to temporarily use DHCP.
Step 2 Connect the AC power cord to the switch and to a grounded AC outlet. The power-on
self-test (POST) begins. During POST, the LEDs blink while a series of tests verify that the
switch functions properly.
Step 3 Wait for the switch to complete POST. It might take several minutes for the switch to
complete POST.
Step 4 Verify that POST has completed by confirming that the SYST LED remains green. If the
switch fails POST, the SYST LED turns amber.
POST errors are usually fatal. Call Cisco Systems immediately if your switch fails POST.

5
Step 5 Press and hold the Mode button for
3 seconds. When all of the LEDs
above the Mode button turn green,
release the Mode button.
If the LEDs above the Mode button
begin to blink after you press the
button, release it. Blinking LEDs
mean that the switch has already
been configured and cannot go into
Express Setup mode. For more
information, see the “Resetting the
Switch” section on page 35.
Step 6 Verify that the switch is in Express Setup mode by confirming that all LEDs above the
Mode button are green. (On some switch models, the RPS LED remains off.)
Step 7 Connect a straight-through
Category 5 Ethernet cable (not
provided) to any 10/100/1000
Ethernet port on the switch front
panel and to the Ethernet port on the
PC.
Step 8 Verify that the LEDs on both Ethernet ports are green.
Step 9 Wait 30 seconds.
Step 10 Launch a web browser on your PC.
Enter the IP address 10.0.0.1 in the
web browser, and press Enter.
SYST
RPS
MASTR
STAT
DUPLX
SPEED
ST
ACK
PoE
Mode button
Catalyst3750G
SERIES
PoE-24
WirelessLANController
SYST
RPS
MASTR
ST
A
T
DUPLX
SPEED
ST
A
CK
P
oE
1X
2X
11X
12X
1234567891011 12
13X
14X
23X
24X
131415161718192021222324
2526
DHCP-enabled PC

6
Step 11 The Express Setup page appears. If it does not appear, see the “In Case of Difficulty”
section on page 34 for help.
Step 12 Enter this information in the Network Settings fields:
•In the Management Interface (VLAN ID) field, the default is 1. Enter a new VLAN ID
only if you want to change the management interface through which you manage the
switch and to which you assign IP information. The VLAN ID range is 1 to 1001.
•In the IP Address field, enter the IP address of the switch. In the IP Subnet Mask field,
click the drop-down arrow, and select an IP Subnet Mask.
•In the Default Gateway field, enter the IP address for the default gateway (router).
•Enter your password in the Switch Password field. The password can be from 1 to 25
alphanumeric characters, can start with a number, is case sensitive, allows embedded
spaces, but does not allow spaces at the beginning or end. In the Confirm Switch
Password field, enter your password again.

7
Step 13 In the Wireless Controller Settings area (see the Figure in Step 11), the stack number
displays the stack-member number of the switch.
Enter this information:
•In the Management Interface (VLAN ID) field, the default is 0. Enter a new VLAN ID
only if you want to change the management interface through which you manage the
controller and to which you assign IP information. If you entered a VLAN ID other
than 1in Step 12, then enter the same VLAN ID for the controller. The VLAN ID
range is 0 to 1001.
•In the IP Address field, enter the IP address of the controller.
•In the IP Subnet Mask field, click the drop-down arrow, and select an IP Subnet Mask.
•In the Default Gateway field, enter the IP address for the default gateway (router).
Note If you are connecting more than one wireless controller switch, multiple rows
appear in the wireless controller settings area.

8
Step 14 (Optional) You can enter the Optional Settings information now or enter it later by using
the device manager interface:
•In the Host Name field, enter a name for the switch. The host name is limited to
31 characters; embedded spaces are not allowed.
•In the Telnet Access field, click Enable if you are going to use Telnet to manage the
switch by using the command-line interface (CLI). If you enable Telnet access, you
must enter a Telnet password.
•In the Telnet Password field, enter a password. The Telnet password can be from
1 to 25 alphanumeric characters, is case sensitive, allows embedded spaces, but does
not allow spaces at the beginning or end. In the Confirm Telnet Password field,
re-enter the Telnet password.
•In the SNMP field, click Enable to enable Simple Network Management Protocol
(SNMP). Enable SNMP only if you plan to manage switches by using
CiscoWorks 2000 or another SNMP-based network-management system.
If you enable SNMP, you must enter a community string in the SNMP Read
Community field, the SNMP Write Community field, or both. SNMP community
strings authenticate access to MIB objects. Embedded spaces are not allowed in
SNMP community strings. When you set the SNMP read community, you can access
SNMP information, but you cannot modify it. When you set the SNMP write
community, you can both access and modify SNMP information.
•In the System Contact field, enter the name of the person who is responsible for the
switch. In the System Location field, enter the wiring closet, floor, or building where
the switch is located.
Step 15 Click Submit to save your settings, or click Cancel to clear your settings.
When you click Submit, the switch is configured and exits Express Setup mode. The PC
displays a warning message and then tries to connect with the new switch IP address. If
you configured the switch with an IP address that is in a different subnet from the PC,
connectivity between the PC and the switch is lost.
Step 16 Disconnect the switch from the PC, and install the switch in your network. See the
“Managing the Switch” section on page 9 for information about configuring and
managing the switch.
If you need to rerun Express Setup, see the “Resetting the Switch” section on page 35.

9
Refreshing the PC IP Address
After you complete Express Setup, you should refresh the PC IP address:
•For a dynamically assigned IP address, disconnect the PC from the switch, and reconnect it to the
network. The network DHCP server assigns a new IP address to the PC.
•For a statically assigned IP address, change it to the previously configured IP address.
4 Managing the Switch
After you complete Express Setup and install the switch in your network, use the device manager or
other management options described in this section for further configuration.
Using the Device Manager
The simplest way to manage the switch is by using the device manager that is in the switch memory.
This is an easy-to-use web interface that offers quick configuration and monitoring. You can access
the device manager from anywhere in your network through a web browser.
Follow these steps:
1. Launch a web browser on your PC or workstation.
2. Enter the switch IP address in the web browser, and press Enter. The device manager page appears.
3. Use the device manager to perform basic switch configuration and monitoring. Refer to the device
manager online help for more information.
4. For more advanced configuration, download and run the Cisco Network Assistant, which is
described in the next section.
Downloading Cisco Network Assistant
Cisco Network Assistant is a software program that you download from Cisco.com and run on
your PC. It offers advanced options for configuring and monitoring multiple devices, including
switches, switch clusters, switch stacks, routers, and access points. Network Assistant is free—there is
no charge to download, install, or use it.
Follow these steps:
1. Go to this Web address: http://www.cisco.com/go/NetworkAssistant.
You must be a registered Cisco.com user, but you need no other access privileges.
2. Find the Network Assistant installer.

10
3. Download the Network Assistant installer, and run it. (You can run it directly from the Web if
your browser offers this choice.)
4. When you run the installer, follow the displayed instructions. In the final panel, click Finish to
complete the Network Assistant installation.
Refer to the Network Assistant online help and the getting started guide for more information.
Command-Line Interface
You can enter Cisco IOS commands and parameters through the CLI. Access the CLI either by
connecting your PC directly to the switch console port or through a Telnet session from a remote PC
or workstation.
Follow these steps:
1. Connect the supplied RJ-45-to DB-9 adapter cable to the standard 9-pin serial port on the PC.
Connect the other end of the cable to the switch console port.
2. Start a terminal-emulation program on the PC.
3. Configure the PC terminal emulation software for:
– 9600 baud
– 8 data bits
– No parity
– 1 stop bit
– No flow control
4. Use the CLI to enter commands to configure the switch. See the software configuration guide and
the command reference for more information.
Other Management Options
You can use SNMP management applications such as CiscoWorks Small Network Management
Solution (SNMS) and HP OpenView to configure and manage the switch. You also can manage it
from an SNMP-compatible workstation that is running platforms such as HP OpenView or
SunNet Manager.
The Cisco IE2100 Series Configuration Registrar is a network management device that works with
embedded Cisco Networking Services (CNS) agents in the switch software. You can use IE2100 to
automate initial configurations and configuration updates on the switch.
See the “Accessing Help Online” section on page 36 for a list of supporting documentation.