Cisco WAP131 User manual

Quick Start Guide
Cisco WAP131 Wireless-N Dual Radio Access
Point with PoE
Package Contents
•Wireless Access Point
•Power Adapter
•This Quick Start Guide
•Product CD
•Ethernet Cable
•Technical Support Contact
•China RoHS (for China SKU only)

2 Cisco WAP131 Quick Start Guide
Welcome
Thank you for choosing the Cisco WAP131 Wireless-N Dual Radio Access
Point with PoE. The Cisco WAP131 is an indoor concurrent dual-band radio
802.11n access point with Power over Ethernet (PoE).
This guide provides the general layout of the Cisco WAP131, describe how
to deploy the Cisco WAP131 in your network, and describe how to
configure the Cisco WAP131. For additional information, see
www.cisco.com/go/100_wap_resources.
Before You Begin
Before you begin the installation, make sure that you have the following
equipment and services:
•A computer with browser support for:
– Internet Explorer 7.0 or later
– Chrome 5.0 or later
– Firefox 3.0 or later
– Safari 3.0 or later
•One or more Ethernet network switches with PoE
Cisco WAP131 Features
Front Panel
The front panel of the Cisco WAP131 consists of three lights: Power,
WLAN, and LAN. For full descriptions of the colors of the lights and their
indications, see “Verifying the Hardware Installation”.
Back Panel
RESET—See “Rebooting the Cisco WAP131 or Resetting to Factory
Defaults” for information on the RESET button.
LAN (PoE)—The RJ-45 Ethernet port is used to power the Cisco WAP131
using PoE. It is an auto-sensing, Gigabit Ethernet (802.3) port used to
connect the Cisco WAP131 to network devices, such as computers,
routers, or switches. We strongly recommend that you use a Category
5e or better cable for gigabit connectivity.
1
2

Cisco WAP131 Quick Start Guide 3
POWER—The POWER button is used to turn the power on and off. It is not
applicable when using PoE.
12V DC—The 12V DC jack is used to connect the supplied power adapter
to the Cisco WAP131 if you are not using PoE.
Kensington Lock Slot—The Kensington lock slot is used to attach a cable
and lock to the Cisco WAP131.
Default Settings
If you are using a Cisco RV Series router, the default range for the DHCP
assigned address is from 192.168.1.100 to 192.168.1.254. Any device
connecting to the same LAN will be assigned an IP address in this range.
Mounting the Cisco WAP131
You can place the Cisco WAP131 horizontally on a surface so that it sits on
its four rubber feet, or place it vertically on a desktop by using the stand on
its left side.
To place the Cisco WAP131 vertically on a desktop, follow these steps:
STEP 1Locate the left side panel of the Cisco WAP131, and rotate the stand
90 degrees clockwise or anticlockwise.
STEP 2Place the stand upward so that the Cisco WAP131 stands on a flat
desktop.
Parameter Default Value
Username cisco
Password cisco
LAN IP Address DHCP address assigned by server
Fallback LAN IP 192.168.1.245
Subnetwork Mask 255.255.255.0
3

4 Cisco WAP131 Quick Start Guide
Placement Tips
• Ambient Temperature—To prevent the Cisco WAP131 from
overheating, do not operate it in an area that exceeds an ambient
temperature of 104°F (40°C).
•AirFlow—Both side panels have vents that must be unobstructed to
prevent overheating.
• Mechanical Loading—The Cisco WAP131 should be level, stable, and
secure to prevent it from sliding or shifting out of position.
Connecting the Cisco WAP131
The default configuration of the Cisco WAP131 has the Wi-Fi radio turned
off. You must perform the initial configuration using a wired Ethernet
connection.
To connect the Cisco WAP131 to the wired network:
STEP 1Connect the Ethernet cable to the Ethernet port of a switch, a router,
or a PC.
STEP 2Connect the other end of the network Ethernet cable to the
Ethernet port of the Cisco WAP131.
STEP 3If PoE is not provided, plug in the supplied power adapter to
provide power to the Cisco WAP131.
After installation, all lights should be active. Refer to “Verifying the
Hardware Installation” for details about the different lights on the Cisco
WAP131.
4

Cisco WAP131 Quick Start Guide 5
Verifying the Hardware Installation
To verify the hardware installation, complete the following tasks:
•Check the cable connections.
•Check the state of the indicator lights.
NOTE If you need help resolving a problem, visit the Cisco Support
Community at www.cisco.com/go/smallbizsupport.
Label Activity Description
POWER Off The Cisco WAP131 has no power.
Solid Green The Cisco WAP131 is powered on, booting, or in
normal operation with DC power supply.
Solid Blue The Cisco WAP131 is powered on, booting, or in
normal operation with PoE 802.at power supply.
Solid Amber The Cisco WAP131 is powered on, booting, or in
normal operation with PoE 802.af power supply.
Solid Red The Cisco WAP131 fails to boot with both
firmware images.
Flashing
(Green/Blue/
Amber)
The Cisco WAP131 is upgrading the firmware,
or is acquiring an IPv4 or IPv6 address.
WLAN Off Wireless is disabled for both 2.4 GHz and 5 GHz.
Solid Green Wireless is enabled in concurrent mode. (The
intensity needs to be the same.)
Solid Amber Wireless is enabled with only 5 GHz in use.
Solid Blue Wireless is enabled with only 2.4 GHz in use.
Flashing Transmitting or receiving data.
LAN Off No Ethernet link.
Solid Green Gigabit Ethernet link is active.
Solid Amber Fast Ethernet link is active.
Flashing Transmitting or receiving data.
5

6 Cisco WAP131 Quick Start Guide
Getting Started with the Configuration
To configure the Cisco WAP131, follow these steps to access the
web-based Configuration Utility and then the Setup Wizard from your
computer:
STEP 1Connect the Cisco WAP131 to the same network (IP subnet) as your
computer. The factory default IP address configuration of the Cisco
WAP131 is DHCP. Make sure that your DHCP server is running and
can be reached.
See “Incorrect IP Address” for troubleshooting information, or if
you do not have a DHCP server.
STEP 2Locate the IP address of the Cisco WAP131.
a. The Cisco WAP131 can be accessed and managed by Cisco
network tools and services including the Cisco FindIT Network
Discovery Utility that enables you to automatically discover all
supported Cisco devices in the same local network segment
as your computer. You can get a snapshot view of each device
or launch the product configuration utility to view and configure
the settings. For more information, see www.cisco.com/go/
findit.
b. The Cisco WAP131 is Bonjour-enabled and automatically
broadcasts its services and listens for services being
advertised by other Bonjour-enabled devices. If you have a
Bonjour-enabled browser, such as Microsoft Internet Explorer
with a Bonjour plug-in, or the Apple Mac Safari browser, you
can find the Cisco WAP131 on your local network without
knowing its IP address.
You can download the complete Bonjour for Microsoft Internet
Explorer browser from Apple’s website by visiting:
http://www.apple.com/bonjour/
c. Locate the IP address assigned by your DHCP server by
accessing your router or DHCP server. See your DHCP server
instructions for more information.
STEP 3Launch a web browser, such as Microsoft Internet Explorer.
STEP 4In the address bar, enter the default DHCP address and press the
Enter key.
STEP 5Enter the default user name of cisco and password of cisco in the
Username and Password fields.
STEP 6Click Log In. The Wireless Access Point Setup Wizard appears.
6

Cisco WAP131 Quick Start Guide 7
STEP 7Follow the Setup Wizard instructions to finish the WAP device
installation. The Setup Wizard turns on the Wi-Fi radio, which
allows you to connect wirelessly.
We strongly recommend that you use the Setup Wizard for the first
installation. For more advanced configurations, see the
Administration Guide. A link to the Administration Guide is found in
“Where to Go From Here”.
Congratulations, you can now start using your Cisco WAP131.
Suggested Next Steps
In case of an error while installing, try the troubleshooting procedures
described in this section.
Troubleshooting
If you cannot display the configuration utility, you can test the ability of the
computer to communicate with the Cisco WAP131 by using ping. To use
ping on a computer running Windows:
STEP 1Verify that the Cisco WAP131 is powered on and the lights indicate
the appropriate links.
STEP 2Locate the Cisco WAP131’s IP address. While there are different
ways to locate the IP address, this procedure uses Cisco FindIT.
a. If you have previously downloaded Cisco FindIT, open Internet
Explorer and launch Cisco FindIT. For more information on
downloading Cisco FindIT, see www.cisco.com/go/findit.
b. In the Cisco FindIT display, place your mouse over the Cisco
WAP131’s name. The Cisco WAP131’s IP address is displayed
along with other device information.
STEP 3Open a command window by choosing Start > Run and enter
cmd.
STEP 4At the command window prompt, enter ping and the Cisco
WAP131’s IP address. In this example, we pinged 192.0.2.10.
If successful, you should get a reply similar to the following:
Pinging 192.0.2.10 with 32 bytes of data:
Reply from 192.0.2.10: bytes=32 time<1ms TTL=128
7

8 Cisco WAP131 Quick Start Guide
If it fails, you should get a reply similar to the following:
Pinging 192.0.2.10 with 32 bytes of data:
Request timed out.
Possible Cause of Installation Failure
Devices Cannot Connect Using Wi-Fi
Complete the Setup Wizard. The Wi-Fi radio on the Cisco WAP131 is
turned off by default, and the Setup Wizard activates it. For users who do
not want to use the Setup Wizard, log into the Cisco WAP131 using a
Category 5e Ethernet cable, and activate the Wi-Fi radio manually. See the
Administration Guide for details on activating the Wi-Fi radio.
No Power
Power up the switch and your computer if they are turned off.
Make sure that your PoE switch is powered on and the lights indicate that
you have a link. See “Verifying the Hardware Installation”.
Verify that the devices on your network are not plugged into a switchable
outlet.
Bad Ethernet Connection
Check the state of the indicator lights. See “Verifying the Hardware
Installation”.
Check the Ethernet cable to ensure that it is firmly connected to your
devices. Devices connected by the Ethernet cable can include the WAP
devices, and routers, any switches, and your computer.
Verify that the connected switch has auto-negotiation enabled. The Cisco
WAP131 and the switch need the same negotiation parameters set.
Bad Image
After a new firmware installation, if the POWER light is solid red, which
indicates that the device fails to boot with both firmware images, contact
system support; see “Where to Go From Here”.
Incorrect IP Address
The most likely cause of connectivity failure is an incorrect IP address. The
Web browser may be pointing to the wrong IP address, or your computer
may be configured with an IP address that is not in the same subnet as the
Cisco WAP131.

Cisco WAP131 Quick Start Guide 9
Because the factory default IP address configuration is DHCP, make sure
that your DHCP server is running and can be reached. You may need to
disconnect and reconnect the devices for them to discover their new IP
addresses from the DHCP server. You can then query the DHCP server for
the new IP address. See Step 2 of “Getting Started with the
Configuration” for more information on how to find the DHCP address.
If the Cisco WAP131 does not receive a DHCP response (there is no DHCP
server on your network) after 60 seconds, the Cisco WAP131 will fallback
to the following default static IP address: 192.168.1.245 and a default mask
of 255.255.255.0. To reach that IP address, be sure that your computer is
on the 192.168.1.xxx network.
Rebooting the Cisco WAP131 or Resetting
to Factory Defaults
To reboot your Cisco WAP131:
•If the Cisco WAP131 uses a power adapter, with the power on, use the
POWER button to reboot the device. The POWER button only functions
when the Cisco WAP131 uses a power adapter.
•If the power supply is PoE, unplug your Ethernet connection for three
seconds and plug it back in.
•With the power on, press the RESET button with an opened paper clip
for less than 10 seconds, or until the lights go off.
– When all the lights go off, release the RESET button.
– Release the RESET button as soon as the lights go off, or you will
restore the Cisco WAP131 to factory default settings and lose your
configurations.
To reset the Cisco WAP131 to factory default settings:
•With the power on, press and hold the RESET button with an opened
paper clip for more than 10 seconds.
– All of the lights will go off.
– Release the RESET button when the power light turns on.
8

10 Cisco WAP131 Quick Start Guide
Where to Go From Here
For EU lot 26 related test result, please check this web page:
www.cisco.com/go/eu-lot26-results.
Support
Cisco Support
Community
www.cisco.com/go/smallbizsupport
Cisco Support and
Resources
www.cisco.com/go/smallbizhelp
Phone Support Contacts www.cisco.com/en/US/support/
tsd_cisco_small_business
_support_center_contacts.html
Cisco Firmware
Downloads
www.cisco.com/go/smallbizfirmware
Select a link to download firmware for Cisco
products. No login is required.
Cisco Open Source
Requests
www.cisco.com/go/
smallbiz_opensource_request
Cisco Partner Central
(Partner Login Required)
www.cisco.com/web/partners/sell/smb
Product Documentation
Cisco WAP131
Administration Guide
www.cisco.com/go/100_wap_resources
Cisco Power Adapters www.cisco.com/go/wap_accessories
9