Cisco Universal Broadband Router uBR7200 Original instructions

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Regulatory Compliance and Safety Information
for the Cisco uBR7200 Series Universal
Broadband Routers
First Published: September 2005
Last Updated: June 2011
Document Revision History
Read this document before installing or servicing the following systems and components:
Revision Date Notes
78-14140-08 June 08, 2011 Updated Statement 2007—EMC Environmental
Conditions for Products Installed in the European
Union, page 78 with the following—Statements
257, 2017, 2020, and European Union (EU)
compliance.
Updated Table 1 for EMC standards.
78-14140-07 November 20, 2009 Updated the list of cable interface line cards with
the new line card uBR-MC88V.
78-14140-06 March 20, 2009 Updated Japanese Electric Appliance and Radio
Laws with Statement 371- Power cable and AC
adapters.
78-14140-05 December 15, 2008 Updated the Regulatory Standards Compliance,
page 76 section with Immunity and Emission
standards.
78-14140-04 March 28, 2008 Added uBR7225VXR-specific information.
78-14140-03 September 1, 2005 Added Korean Certification Information.

2
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Contents
Note Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS 3260) should install,
replace, or service this equipment. Install the system in accordance with the U.S. National Electric Code
if you are in the United States.
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Contents
•Translated Safety Warnings, page 5
– Statement 5—Chassis Lifting Warning, page 5
Equipment Part Number
Cisco universal broadband routers UBR7246, UBR7246VXR, UBR7225VXR
Cable interface line cards UBR-MC28C, UBR-MC28U/X, UBR-MC16E, UBR-MC16S, UBR-MC16C,
UBR-MC16B,UBR-MC16U/X, UBR-MC14C, UBR-MC12C, UBR-MC11C,
UBR-MC11, uBR-E-16U, uBR-E-28U, uBR-MC88V
Port adapters PA-4E, PA-FE-TX, PA-FE-FX, PA-2A-4T1C-OC3SM, PA-A2-4T1C-T3ATM,
PA-A2-4E1XC-OC3SM, PA-A2-4E1XC-E3ATM, PA-2H, PA-H-UPG, PA-2H,
PA-8T-V35, PA-8T-X21, PA-8T-232, PA-4E1G-75, PA-4E1G-120, PA-4T, PA-E3,
PA-2E3, PA-MC-E3, PA-T3, PA-2T3, PA-2T1, PA-MC-4T1, PA-MC-8T1,
PA- M C-8DSX1, PA-POS- OC3SML, PA-POS-OC3SMI, PA-POS-OC3SMM,
PA-2FEISL-TX, PA-2FEISL-FX, PA-12E/2FE, PA-GE, PA-SRP-OC12SMX,
PA-SRP-OC12MM, PA-SMP-OC12SML, PA-SRP-OC12SMI, PA-A1-OC3SMI,
PA-A1-OC3MM, PA-A3-T3, PA-A3-E3, PA-A3-OC3MM, PA-A3-OC3SMI,
PA-A3-OC3SML, PA-MC-T3, PA-8E
Network processing engines (NPEs) NPE150, NPE175, NPE200, NPE225, NPE300, NPE400, NPE-G1, and NPE-G2.
Note The uBR7246VXR and uBR7225VXR routers need shielding cables for NPE
processor cards.
AC and DC power supplies PWR-UBR7200-AC, PWR-UBR7200-AC=, PWR-UBR7200/2-AC,
PWR-UBR7225VXR-AC
PWR-UBR7200-DC, PWR-UBR7200-DC=, PWR-UBR7200/2-DC
Fan tray MAS-UBR7200-FAN
Chassis midplane MAS-UBR-7246VXRMP=, MAS-UBR-7246MP=, MAS-UBR-7225VXRMP=

3
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Contents
– Statement 12—Power Supply Disconnection Warning, page 8
– Statement 25—Warning for Norway and Sweden, page 9
– Statement 35—Warning for Finland, page 10
– Statement 36—Warning for Sweden, page 10
– Statement 43—Jewelry Removal Warning, page 10
– Statement 48—Stacking the Chassis Warning, page 12
– Statement 61—Power Supply Wiring Warning, page 13
– Statement 89—Telecommunications Lines Warning, page 14
– Statement 106—More Than One Power Cord, page 15
– Statement 164—Two Person Lifting Requirement, page 15
– Statement 181—Wrist Strap and Midplane Contact Warning, page 16
– Statement 196—Chassis Disconnection Warning, page 18
– Statement 285—Electrical Connection Warning, page 20
– Statement 342—Before Connecting to System Power Supply, page 21
– Statement 1001—Work During Lightning Activity, page 22
– Statement 1003—DC Power Disconnection, page 22
– Statement 1004—Installation Instructions, page 24
– Statement 1006—Chassis Warning for Rack-Mounting and Servicing, page 25
– Statement 1007—TN and IT Power Systems, page 30
– Statement 1008—Class 1 Laser Product, page 31
– Statement 1015—Battery Handling, page 32
– Statement 1016—Invisible Laser Radiation, page 33
– Statement 1017—Restricted Area, page 34
– Statement 1018—Supply Circuit, page 36
– Statement 1021—SELV Circuit, page 37
– Statement 1022—Disconnect Device, page 39
– Statement 1023—No. 26 AWG, page 40
– Statement 1024—Ground Conductor, page 41
– Statement 1025—Use Copper Conductors Only, page 43
– Statement 1026—WAN Port Static Shock, page 44
– Statement 1027—Class 1 LED Product, page 45
– Statement 1028—More Than One Power Supply, page 46
– Statement 1029—Blank Faceplates and Cover Panels, page 48
– Statement 1030—Equipment Installation, page 51
– Statement 1032—Lifting the Chassis, page 52
– Statement 1033—SELV-IEC 60950 DC Power Supply, page 54
– Statement 1040—Product Disposal, page 55
– Statement 1041—Disconnecting Telephone-Network Cables, page 56

4
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Contents
– Statement 1043—Installation Hazard, page 57
– Statement 1045—Short-circuit Protection, page 59
– Statement 1046—Installing or Replacing the Unit, page 61
– Statement 1047—Overheating Prevention, page 63
– Statement 1051—Laser Radiation, page 64
– Statement 1064—Grounded Equipment, page 66
– Statement 1071—Warning Definitions, page 67
– Statement 1078—Not Intended to be Directly Connected to the Cable Distribution System,
page 72
•European Directives, page 73
– Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European
Community, Switzerland, Norway, Iceland and Liechtenstein, page 74
– Statement 2002—Declaration of Conformity with Regard to the Directives 2006/95/EC and
2004/108/EC, page 74
– Statement 2017—Class A Notice for FCC, page 75
– Statement 2019—FCC Declaration of Conformity Information (for USA only), page 75
•Regulatory Standards Compliance, page 76
•Statement 2007—EMC Environmental Conditions for Products Installed in the European Union,
page 78
– European Union (EU) Compliance, page 78
– Statement 2020—Class A Warning Notice, page 78
– Statement 191—VCCI Class A Warning for Japan, page 80
– Statement 191—VCCI Class A Warning for Japan, page 80
– Statement 256—Class A Warning for Hungary, page 80
– Statement 257—Class A Notice for Taiwan and Other Traditional Chinese Markets, page 81
– Korean Certification Information, page 81
– Statement 294—Class A Warning for Korea, page 82
– Statement 2021—Class A Notice for Canada, page 82
•GR-1089-Core Intrabuilding Lightning—Immunity Requirements, page 83
•Port Adapter Compliance Information, page 83
– FCC Part 68 Notice, page 83
– CS-03 Certification for Canada, page 84
– JATE Certification for Japan, page 86
– RRL Certification for Korea, page 87
•Port Adapter Installation Safety Information, page 87
•Japanese Electric Appliance and Radio Laws, page 88
– Statement 371—Power Cable and AC Adapter, page 88
•Related Documentation, page 89
•Obtaining Documentation and Submitting a Service Request, page 89

5
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Translated Safety Warnings
Translated Safety Warnings
This section includes translations in multiple languages of the warnings that may appear in your product
documents.
Statement 5—Chassis Lifting Warning
Warning Two people are required to lift the chassis. Grasp the chassis underneath the lower edge and lift
with both hands. To prevent injury, keep your back straight and lift with your legs, not your back. To
prevent damage to the chassis and components, never attempt to lift the chassis with the handles
on the power supplies or on the interface processors, or by the plastic panels on the front of the
chassis. These handles were not designed to support the weight of the chassis.
Statement 5
Waarschuwing
Er zijn twee mensen nodig om het frame op te tillen. Het frame dient onder de onderste rand
vastgegrepen en met beide handen omhooggetild te worden. Om te voorkomen dat u letsel oploopt,
dient u uw rug recht te houden en met behulp van uw benen, niet uw rug, te tillen. Om schade aan
het frame en de onderdelen te voorkomen, mag u nooit proberen om het frame op te tillen aan de
handvatten op de voedingen of op de interface-processors of aan de kunststof panelen aan de
voorkant van het frame. Deze handvatten zijn niet ontworpen om het gewicht van het frame te
dragen.
Varoitus
Asennuspohjan nostamiseen tarvitaan kaksi henkilöä. Ota ote asennuspohjan alareunasta ja nosta
molemmin käsin. Pitäen selkäsi suorana nosta jalkojen (ei selän) avulla, jotta välttäisit
loukkaantumista. Älä yritä nostaa asennuspohjaa virtalähteen tai liitäntäprosessorin kahvoista tai
asennuspohjan etuosan muovipaneeleista, jotta estät asennuspohjan ja rakenneosien
vaurioitumisen. Näitä kahvoja ei ole suunniteltu kestämään asennuspohjan painoa.
Attention
Il faut deux personnes pour soulever le châssis. Le saisir par son rebord inférieur et soulever des
deux mains. Pour éviter tout trauma de la région lombaire, garder le dos droit et soulever la charge
en redressant les jambes. Pour éviter d'endommager le châssis et ses composants, ne jamais tenter
de le soulever par les poignées des blocs d'alimentation ou des processeurs d'interface, ni par les
panneaux en plastique à l'avant du châssis. Ces poignées ne sont pas prévues pour supporter le
poids du châssis.
Warnung
Zum Anheben des Chassis werden zwei Personen benötigt. Fassen Sie das Chassis unterhalb der
unteren Kante an und heben es mit beiden Händen an. Um Verletzungen zu vermeiden, ist der Rücken
aufrecht zu halten und das Gewicht mit den Beinen, nicht mit dem Rücken, anzuheben. Um Schäden
an Chassis und Bauteilen zu vermeiden, heben Sie das Chassis nie an den Kunststoffabdeckungen
vorne am Chassis oder mit den Griffen am Netzgerät oder an den Schnittstellenprozessoren an. Diese
Griffe sind nicht so konstruiert, daß sie das Gewicht des Chassis tragen könnten.
Avvertenza
Il telaio va sollevato da due persone. Afferrare il telaio al di sotto del bordo inferiore e sollevare con
entrambe le mani. Per evitare infortuni, mantenere la schiena diritta e sollevare il peso con le
gambe, non con la schiena. Per evitare danni al telaio ed ai componenti, non provare mai a sollevare
il telaio tramite le maniglie sugli alimentatori o sui processori di interfaccia oppure tramite i
pannelli in plastica sulla parte anteriore del telaio. Queste maniglie non sono state progettate per
sostenere il peso del telaio.

6
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Translated Safety Warnings
¡Advertencia!
Se necesitan dos personas para levantar el chasis. Sujete el chasis con las dos manos por debajo
del borde inferior y levántelo. Para evitar lesiones, mantenga la espalda recta y levántelo con la
fuerza de las piernas y no de la espalda. Para evitar daños al chasis y a sus componentes, no intente
nunca levantar el chasis por las asas de las fuentes de alimentación o de los procesadores de
interfase, ni por los paneles de plástico situados en el frontal del chasis. Las asas no han sido
diseñadas para soportar el peso del chasis.
Advarsel
Det er nødvendig med to personer for å løfte kabinettet. Ta tak i kabinettet under den nedre kanten,
og løft med begge hender. Unngå personskade ved å holde ryggen rett og løfte med bena, ikke
ryggen. Unngå skade på kabinettet og komponentene ved å aldri prøve å løfte kabinettet etter
håndtakene på strømforsyningsenhetene, grensesnittprosessorene eller i plastpanelene foran på
kabinettet. Disse håndtakene er ikke beregnet på å tåle vekten av kabinettet.
Aviso
São necessárias duas pessoas para levantar o chassis. Agarre o chassis imediatamente abaixo da
margem inferior, e levante-o com ambas as mãos. Para evitar lesões, mantenha as suas costas
direitas e levante o peso com ambas as pernas, sem forçar as costas. Para prevenir danos no chassis
e nos seus componentes, nunca tente levantá-lo pelas asas das unidades abastecedoras de energia,
nem pelos processadores de interface, ou pelos painéis plásticos localizados na frente do chassis.
Estas asas não foram criadas para suportar o peso do chassis.
Varning!
Det krävs två personer för att lyfta chassit. Fatta tag i chassit under den nedre kanten och lyft med
båda händerna. För att undvika skador skall du hålla ryggen rak och lyfta med benen, inte ryggen.
Chassit och delarna kan skadas om du försöker lyfta chassit i handtagen på
strömförsörjningsenheterna eller gränssnittsprocessorerna, eller i plastpanelerna på chassits
framsida. Handtagen är inte konstruerade för att hålla chassits tyngd.

7
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Translated Safety Warnings
Aviso
São necessárias duas pessoas para suspender o chassi. Segure o chassi por baixo das
extremidades da parte inferior e suspenda-o com as duas mãos. Para evitar lesões, mantenha-se
ereto e suspenda-o flexionando as pernas sem forçar as costas. Para evitar danos no chassi e em
seus componentes, nunca tente suspendê-los pelas alças nas fontes de alimentação ou nos
processadores da interface ou pelos painéis plásticos frontais.
Essas alças não foram projetadas para suportar o peso do chassi.
Advarsel
Der kræves to personer til at løfte chassiset. Tag fat i chassiset under den nederste kant og løft med
begge hænder. For at forhindre skader, skal du holde din ryg ret og løfte med benene, ikke ryggen.
For at forhindre beskadigelse af chassiset og komponenter, må du aldrig forsøge at løfte chassiset i
håndtagene på strømforsyningen eller på interfaceprocessoren, eller i plastikpanelerne på forsiden
af chassiset.
Disse håndtag er ikke beregnede til at bære vægten af chassiset.

8
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Translated Safety Warnings
Statement 12—Power Supply Disconnection Warning
Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units;
disconnect the power at the circuit breaker on DC units.
Statement 12
Waarschuwing
Voordat u aan een frame of in de nabijheid van voedingen werkt, dient u bij wisselstroom toestellen
de stekker van het netsnoer uit het stopcontact te halen; voor gelijkstroom toestellen dient u de
stroom uit te schakelen bij de stroomverbreker.
Varoitus
Kytke irti vaihtovirtalaitteiden virtajohto ja katkaise tasavirtalaitteiden virta suojakytkimellä, ennen
kuin teet mitään asennuspohjalle tai työskentelet virtalähteiden läheisyydessä.
Attention
Avant de travailler sur un châssis ou à proximité d'une alimentation électrique, débrancher le
cordon d'alimentation des unités en courant alternatif ; couper l'alimentation des unités en courant
continu au niveau du disjoncteur.

9
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Translated Safety Warnings
Statement 25—Warning for Norway and Sweden
Warnung
Bevor Sie an einem Chassis oder in der Nähe von Netzgeräten arbeiten, ziehen Sie bei
Wechselstromeinheiten das Netzkabel ab bzw. schalten Sie bei Gleichstromeinheiten den Strom am
Unterbrecher ab.
Avvertenza
Prima di lavorare su un telaio o intorno ad alimentatori, scollegare il cavo di alimentazione sulle
unità CA; scollegare l'alimentazione all’interruttore automatico sulle unità CC.
Advarsel
Før det utføres arbeid på kabinettet eller det arbeides i nærheten av strømforsyningsenheter, skal
strømledningen trekkes ut på vekselstrømsenheter og strømmen kobles fra ved strømbryteren på
likestrømsenheter.
Aviso
Antes de trabalhar num chassis, ou antes de trabalhar perto de unidades de fornecimento de
energia, desligue o cabo de alimentação nas unidades de corrente alternada; desligue a corrente
no disjuntor nas unidades de corrente contínua.
¡Advertencia!
Antes de manipular el chasis de un equipo o trabajar cerca de una fuente de alimentación,
desenchufar el cable de alimentación en los equipos de corriente alterna (CA); cortar la
alimentación desde el interruptor automático en los equipos de corriente continua (CC).
Varning!
I nnan du arbetar med ett chassi eller nära strömförsörjningsenheter skall du för växelströmsenheter
dra ur nätsladden och för likströmsenheter bryta strömmen vid överspänningsskyddet.
Warning Connect the device to a grounded power outlet. Statement 25
Advarsel
Apparatet skal kobles til en jordet stikkontakt.
Varning!
Apparaten skall anslutas till jordat nätuttag.

10
Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers
78-14140-08
Translated Safety Warnings
Statement 35—Warning for Finland
Statement 36—Warning for Sweden
Statement 43—Jewelry Removal Warning
Warning Alleviates ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Äjä katso
säteeseen. Statement 35
Warning Invisible laser radiation when this component is opened and the preregulation is disabled. Do not
look into the laser beam.
Statement 36
Varning!
Osynlig laserstrålning när denna del är öppen och förregleringen är urkopplad. Rikta inte blicken in
mot strålen.
Warning Before working on equipment that is connected to power lines, remove jewelry (including rings,
necklaces, and watches). Metal objects will heat up when connected to power and ground and can
cause serious burns or weld the metal object to the terminals.
Statement 43
Waarschuwing
Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief
ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met
stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen
voorwerp aan de aansluitklemmen lassen.
Varoitus
Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut
(sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat
yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata
metalliesineet kiinni liitäntänapoihin.
Attention
Avant d’accéder à cet équipement connecté aux lignes électriques, ôter tout bijou (anneaux,
colliers et montres compris). Lorsqu’ils sont branchés à l’alimentation et reliés à la terre, les objets
métalliques chauffent, ce qui peut provoquer des blessures graves ou souder l’objet métallique aux
bornes.
Warnung
Vor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschließlich
Ringe, Ketten und Uhren) abnehmen. Metallgegenstände erhitzen sich, wenn sie an das Netz und die
Erde angeschlossen werden, und können schwere Verbrennungen verursachen oder an die
Anschlußklemmen angeschweißt werden.