City Theatrical Vero Net 7400-5708M User manual

7400-5708MVero Net™
Transceiver
Installation and Quick Start Guide
Rev 1.2
©2012, City Theatrical, Inc.
475 Barell Ave., Carlstadt, NJ 07072
Voice: 800-230-9497, 201-549-1160
Fax: [phone]
INSTALLING THE 7400-5708MSHOW DMX VERO NET TRANSCEIVER
Installation
Install the SHoW DMX Vero Net Transceiver in a suitable location, following the instructions
below. When selecting a mounting location, note that for best results the antennas in your
system must be within sight of each other.
Warning
To avoid electric shock, do not energize any circuits before all internal and external electrical
and mechanical clearances are checked to assure that all assembled equipment functions
safely and properly.
Important use notes
This unit must be used with voltages below 600V
This unit must be installed in accordance with the National Electrical Code, ANSI/NFPA 70,
where the ambient temperature does not exceed 40°C (104°F) maximum.
Grounding
This enclosure has been provided with a ground bond jumper for ground connection between
the back box and the cover. This jumper must be installed asshown in the drawing below,
using the provided hardware.
Mounting Bracket
The provided mounting Bracket Base can be mounted on a surface or a vertical pipe. For
surface mounting, the Bracket base is provided with slots and holes suitable for #10 / M4
screws or similar fasteners.
Surface Mounting
Mount the Mounting Bracket Base in the desired location using four x #10 / M4 screws (by
others, as above).
Page 1

Slide the mating Mounting Bracket (attached to the Unit) into the Mounting Bracket Base until
the locking clip engages, and install the provided 8-18 x .500” SS Thread Forming Torx Button
Head Security Screw, in the hole on the left side of the Bracket assembly.
Mounting Orientation
The 7400-5708MSHoW DMX Vero Net Transceiver must be mounted exclusively in an
upright mounting position with the cable entries on the bottom and antenna connector on the
top as shown in the drawing above.
Pipe Mounting
The SHoW DMX Vero can also be mounted on a pipe.
Page 2 of 7

Attach the Mounting Bracket Base to a pipe using a stainless steel hose clamp as shown:
Slide the mating Mounting Bracket (attached to the Unit) into the Mounting Bracket Base until
the locking clip engages, and install the retaining screw.
Cable or Conduit Entry
The unit enclosure is provided with ½” NPT entry holes fitted with liquid-tight cable grips for
use with outdoor use cables (by installer) for power, DMX, and Ethernet connection.
The recommended torque for these cable grips is as follows:
LockingNut40‐45inchpounds
SealingNut50‐55inchpounds
If outdoor use conduit is used instead, it is recommended that the conduit be sealed after
installation to prevent moisture entry, including free air exchange, in order to minimize the
chance of condensation buildup.
Page 3 of 7

Mains Wire Installation and Termination
Install the mains cable or conduit in the entry provided as shown in the drawing below. A
liquid tight cable grip is provided for use with suitable outdoor rated cable with diameter range
of .170”/4,3mm - .450”/11,4mm.
When cable is used, strip outer jacket 6.0”/150mm.
The mains connection is a 3 pos. plug/socket type terminal block which may be disconnected
for ease of assembly. Strip insulation from individual conductors .25”/7mm and terminate in
the provided screw terminal socket (see illustration above) Mains terminations are ash shown
and are marked on the unit.
DMX512 Wire Termination
The SHoW DMX Vero Net Transceiver is provided with a PCBA mount terminal block for
DMX connection (see illustration above). DMX Input / Output connections are as shown and
are marked on the unit.
Page 4 of 7

Page 5 of 7
ou can configure the Vero Net Transceiver’s basic operating settings using the System
in the detail above.
Ethernet Cable entry
The unit is provided with an RJ45 Ethernet Jack for Ethernet connection. Install the Ethernet
cable using the entry provided. An RJ45 Ethernet Plug must be installed on the Ethernet
cable after the cable is pulled into the box, using the standard TIA-EIA T568B pin out.
Installing the Cover
The 7400-5707MSHoW DMX Vero Net Transceiver has a two part cover, with the outer
plastic cover connected to the inner metal cover with a hinge. Install the metal inner cover
using the eight provided 6- 32 x .375” SS Truss Head Machine Screws. Hand install these
screws until the screw threads are fully engaged with the mating PEM Nut, then tighten to 4
inch pounds.
The outer cover is then closed and secured with the provided 8-18 x .500” SS Thread
Forming Torx Button Head Security Screw, installed in the provided hole on the left side of the
cover assembly.
THE 7400-5708 SHOW DMX VERO NET TRANSCEIVER SETTINGS
Configuration
Y
Settings switches shown

Page 6 of 7
Configu 512 termination On or Off. Turn On for end-of-line DMX512
onnection.
Receiver (Rx) On, or Transmitter (Tx) Off. Selects Receiver or Transmitter
peration
3, Reset: On or Off. Switch On to Reset
and install Host
nd radio firmware upgrades from a connected USB Memory device.
tore the system to factory default settings:
D to blink rapidly
3. Switch P1 to Off
sceiver for use as a transmitter and at least one Vero Net Transceiver for
ave
rs open so you have access to the System Settings controls and internal
EDS.
re using as a transmitter by setting P4 to the Transmitter (Tx) position (switch OFF).
a receiver(s) are correctly set with P4 set to
e Receiver (Rx) position (switch ON).
Latency broadcast mode (this
HoW ID matches 5702 SHoW DMX SHoW Baby).
ower up the system and apply DMX512 control to the transmitter.
heck that the Data present LEDs on all units are lit and solid.
onfirm the In Range LED on all receivers is lit.
ration switches:
P5, DMX Term: DMX
c
P4, Rx/Tx:
o
P
P2 Bootloader: On or Off. Sets the unit to Bootloader mode to upload
a
P1 Default: On or Off. To res
1. Set P1 Default to On
2. Wait for PCBA LE
QUICK SETUP
For a basic 7400-5708MSHoW DMX Vero Net System you will need one 7400-5708M
SHoW
DMX Vero Net Tran
use as a receiver.
1. Install the Vero Net units as shown in the installation instructions, including all DMX
and power connections. Locate the units so the antennas are within sight of each
other (if you are using directional or other special use antennas, consult the Manual
and SHoW DMX Neo Installation and Application Guide for installation details). Le
the cove
L
2. All Vero Net units are shipped configured as receivers. Configure the Vero Net unit you
a
3. Confirm the Vero Net(s) you are using as
th
4. Verify that all Vero Net units in the system are set to the same SHoW ID. The SHoW
DMX Vero Net Transceiver is preset at the factory with SHoW ID 201 for Adaptive
Spread Spectrum Frequency Hopping and Neo Low
S
5. P
6. C
7. C

Page 7 of 7
8. Check the Received Signal Strength LEDs - at least two should be lit.
9. Confirm DMX is being output as wired DMX512 by the receivers.
SHoW ID
New Maximum Bandwidth Technology™ allows SHoW DMX to change from Frequency
Hopping to Wide Band Digital Modulation, which allows it to narrow its output to smaller areas
of the 2.4GHz spectrum, such as Wi-Fi channel 14 where (in the U.S.) no Wi-Fi broadcast
takes place. This allows SHoW DMX to avoid all Wi-Fi interference in an otherwise saturated
spectrum. No other wireless DMX system can make this claim. This is accomplished
simply by selecting a SHoW ID on the user interface or via RDM.
SHoW DMX Neo system uses SHoW IDs as a quick way to set RF configuration options.
Each SHoW ID represents a combination of one of 16 hopping patterns and one of four
bandwidth settings. 7400-5708MVero Transceiver supports SHoW DMX Classic, Neo and
Neo Adaptive SHoW IDs.
The Transmitter and Receiver SHoW IDs must match for the units to communicate.
See the 7400-5708 SHoW DMX Vero Net Users Manual for more details about other system
setting options. The Users Manual and the SHoW DMX Neo Installation and Application
Guide can be downloaded from the City Theatrical website: www.citytheatrical.com.