Clage Zip kxf 2.1 User manual

804984 - SP_Zip KXF 2.1 Fein lter - 11.22 v1.0 Seite 1 von 16

v1.0 11.22

804984DE

de > 

en > 

fr > 

Zip KXF2.1 Feinﬁlter

Zip KXF 2.1 Fine ﬁlter

Gebrauchs- und Montageanleitung

Operating and installation instructions

Seite 2 von 16 804984 - SP_Zip KXF 2.1 Feinlter - 11.22 v1.0

• Nur für die Verwendung in Innenräumen vorgesehen.

• Nicht an Orten installieren, die direktem Sonnenlicht oder Temperaturen <4°C oder

>40°C ausgesetzt sind.

• Der sichere Betriebswasserdruck beträgt mindestens 70 kPa, maximal 700 kPa.

• Nicht dort installieren, wo die Wasserqualität unbekannt oder mikrobiologisch bedenk-

lich ist.

• Nach einer Zeit der Nichtbenutzung den Filter oder die Tanks gründlich durchspülen.

• Aus Sicherheitsgründen sollten alle Filterpatronen in Abständen von höchstens 12

Monaten ausgetauscht werden.

• Tauschen Sie jeden Filter aus, wenn der Wasserdurchﬂuss nachlässt oder wenn ein

unangenehmer Geschmack oder Geruch auftritt.

WARNUNG

Um das Risiko der Aufnahme von Verunreinigungen zu verringern:

• Verwenden Sie kein Wasser, das mikrobiologisch unsicher oder von unbekannter

Qualität ist, ohne eine angemessene Desinfektion vor oder nach dem System.

ACHTUNG

Verringerung des Risikos von Sachschäden aufgrund von Wasseraustritt:

• Vor der Installation und Verwendung lesen und befolgen Sie die Gebrauchsanweisung.

• Installation und Verwendung MÜSSEN allen staatlichen und örtlichen Vorschriften für

Sanitärinstallationen entsprechen.

• Schützen Sie das System vor Frost und nehmen Sie die Filterpatrone heraus, wenn die

Temperaturen voraussichtlich unter 4,4°C fallen werden.

• Installieren Sie das System nicht in Bereichen, in denen die Umgebungstemperaturen

über 43°C steigen können.

• Nicht an Warmwasserleitungen installieren. Die maximale Zulauftemperatur beträgt

38°C.

• Verwenden Sie keinen Gasbrenner oder andere Hochtemperaturquellen in der Nähe

des Systems, der Kartuschen, der Kunststofffittings oder der Kunststoffrohre.

• Nicht in direktem Sonnenlicht oder im Freien installieren.

• Vergewissern Sie sich, dass alle Rohre und Verbindungen sicher und leckfrei sind.

• Die Einweg-Filterpatrone MUSS alle 12 Monate, bei Erreichen der Nennkapazität oder

früher ausgetauscht werden, wenn eine merkliche Verringerung der Durchflussrate

auftritt.

Inhaltsverzeichnis

1. Sicherheitshinweise

. Sicherheitshinweise....................................................................................

. Auswechseln der internen Filterpatrone ..................................................................

Filter austauschen: .....................................................................................

. Einsetzen und Entfernen von Wasserleitungen aus John Guest-Verbindungen .................................

. Informationen ........................................................................................

. Filterdaten - . Micron ................................................................................

804984 - SP_Zip KXF 2.1 Feinlter - 11.22 v1.0 Seite 3 von 16

Diese Anleitung bezieht sich auf den Austausch des Filters im Zip HydroTap-

Produkt, bei dem der Filter im Inneren montiert ist. Stellen Sie sicher, dass Sie für

die Filterspülung einen 10-Liter-Behälter zur Verfügung haben.

Während des Austauschs kann etwas Wasser aus dem Filterkopf (Sockel) tropfen.

Halten Sie ein Handtuch bereit, um etwaiges Tropfwasser aufzuwischen.

Filter austauschen:

1. Gehen Sie im Menü auf Filterspülung, um die Wasserzufuhr zu isolieren. Je nach

Produkt gibt es Abweichungen. Siehe die jeweilige Geräte-Anleitung.

2. Lassen Sie den Systemdruck über den Absperrhahn der Filterspülung ab, ein

kurzes Öffnen und Schließen genügt. Verwenden Sie den Eimer, um den austre-

tendes Wasser aufzufangen.

3. Greifen Sie die Filterpatrone, drehen Sie die Patrone eine Vierteldrehung nach

links und ziehen Sie sie vorsichtig nach unten.

Achtung: Eine kleine Menge Restwasser kann austreten.

4. Kippen Sie die Kartusche nicht, da sonst Wasser auslaufen kann.

5. Packen Sie die Ersatzkartusche aus, schreiben Sie das aktuelle Datum auf das

Etikett und entfernen Sie die Hygienekappe.

6. Vermeiden Sie es, die O-Ringe des Filters und die Filteröffnung zu berühren, da

dies zu einer bakteriellen Verunreinigung der Kartusche führen kann.

7. Schieben Sie die neue Patrone nach oben in den Filterkopf.

8. Drehen Sie die Patrone um eine Vierteldrehung nach rechts, bis die Patrone zum

Stillstand kommt und einrastet.

9. Nehmen Sie den Filterspülschlauch, der sich hinter der Filterpatrone befin-

det, und führen Sie den Schlauch in einen Eimer. Öffnen Sie den Absperrhahn

der Filterspülung. Drücken Sie im Menü auf Einstellen oder Start, um den

Wasserdurchfluss zu starten und den Filter zu spülen. Lassen Sie vor dem

Gebrauch mindestens 10Liter Wasser durch die Kartusche laufen, um den Filter

zu aktivieren. Schließen Sie den Absperrhahn der Filterspülung und setzen Sie

ihn wieder hinter der Filterpatrone ein. Beenden Sie nun die Filterspülung oder

drücken Sie „Filterspülung aus“, um den Durchfluss zu stoppen. (Es kann etwa

3Minuten dauern, die 10Liter zu spülen.)

10.Wischen Sie verschüttete Flüssigkeiten auf und entsorgen Sie die verbrauchte

Filterpatrone und die Verpackung ordnungsgemäß.

11. Schließen Sie die Filterklappe des Gerätes.

12.Setzen Sie den internen Filterzähler ihres HydroTap-Gerätes zurück. Folgen Sie

dazu der Anleitung des Gerätes.

1. drehen

2. abziehen

1. einführen

2. drehen

Filter entfernen

Filter installieren

2. Auswechseln der internen Filterpatrone

Seite 4 von 16 804984 - SP_Zip KXF 2.1 Feinlter - 11.22 v1.0

3. Einsetzen und Entfernen von Wasserleitungen aus John Guest-Verbindungen

Allgemeine Anweisungen für John Guest-

Verbindungen

NOTE: Stellen Sie sicher, dass alle John

Guest Rohrenden sauber und rechtwinklig

abgeschnitten sind.

Weitere Informationen

Wenn der Filter in ein Gerät eingebaut ist, finden Sie in der Bedienungsanleitung des Geräts weitere produktspezi-

fische Informationen und Hinweise zur Vermeidung von Verunreinigungen durch unsachgemäße Handhabung und

Installation.

Garantie

Zip-Wasserfilterpatronen fallen nicht unter die Standardgarantie von CLAGE, da die Lebensdauer des Filters je nach

Wasserqualität und Nutzungshäufigkeit variieren kann.

4. Informationen

804984 - SP_Zip KXF 2.1 Feinlter - 11.22 v1.0 Seite 5 von 16

5. Filterdaten - 0.2 Micron

* Der Begriff “bakteriostatisch” bedeutet, dass das System den

Durchgang oder das Wachstum von Bakterien, die möglicherweise

bereits im einströmenden Wasser vorhanden sind, begrenzt. Er

bedeutet nicht, dass das Wasser welches das System verlässt,

sicherer zu trinken ist als das Wasser, das in das System eintritt.

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000

AS/NZS 3497

WM-0350001

Global-Mark.com.au

BETRIEBSSPEZIFIKATIONEN

• Druckanforderungen: 10 -125 psi (0,7 - 8,6 bar), nicht

schlagend

• Temperatur: 35 -100°F (2-38°C)

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

LEISTUNG BEI GESUNDHEITSANSPRÜCHEN VON NSF ZERTIFIZIERT

Dieses System wurde gemäß den NSF/ANSI-Normen 42 und 53 auf die Reduzierung der unten aufgeführten Stoffe

geprüft. Die Konzentration der angegebenen Stoffe im Wasser, das in das System eintritt, wurde auf eine Konzentration

reduziert die kleiner oder gleich dem zulässigen Grenzwert für das Wasser ist, welches das System verlässt. Wie in den

NSF/ANSI-Standards 42 und 53 angegeben.

Das System wurde von NSF International gemäß NSF/ANSI

Standard 42 und 53 auf die Reduzierung von:

STANDARD NR.42 - STANDARD NR.53 -

ÄSTHETISCHE AUSWIRKUNGEN

GESUNDHEITLICHE AUSWIRKUNGEN

Bakteriostatische Wirkungen Chemikalienreduzierung

Chemische Reduktion Blei

Geschmack & Geruch Mechanische Filtration

Chlor Zyste

Mechanische Filtrierung

Nominaler Partikelgehalt Klasse I

AS/NZS 3497

WM -0350001WM -0350001

Global-Mark.com.auGlobal-Mark.com.au

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

Modell Durchfluss Kapazität Artikel #

0.2mic KXF2.1 Feinfilter

1.5S

5.678 l/min 6813 L 93702

Page 6 of 16 804984 - SP_Zip KXF 2.1 Fine lter - 11.22 v1.0

Contents

. Safety Instructions.....................................................................................

. Exchange of internal filter ..............................................................................

Change the Filter: .......................................................................................

. Inserting & Removing Water Supply Lines from John Guest Fittings ..........................................

. Other information .....................................................................................

. Filter Performance Data - . Micron ....................................................................

• Designed for indoor use only.

• Do not install where exposed to direct sunlight or temperatures <4°C or >40°C.

• Minimum safe operating water pressure is 70 kPa, maximum 700 kPa.

• Do not install where water quality is unknown or microbiologically unsafe.

• After a period of non-use thoroughly ﬂush the ﬁlter or tanks.

• For safety’s sake, replace all ﬁlter cartridges at intervals of 12 months or less.

• Replace any ﬁlter if water ﬂow slows or if unpleasant tastes or odours occur.

WARNING

To reduce the risk associated with the ingestion of contaminants:

• Do not use with water that is microbiologically unsafe or of unknown quality without

adequate disinfection before or after the system.

CAUTION

To reduce the risk associated with property damage due to water leakage:

• Read and follow Use Instructions before installation and use of this system.

• Installation and use MUST comply with all state and local plumbing codes.

• Protect from freezing, remove filter cartridge when temperatures are expected to

drop below 4.4°C.

• Do not install systems in areas where ambient temperatures may go above 43° C.

• Do not install on hot water supply lines. The maximum operating water temperature of

this system is 38°C.

• Do not use a gas torch or other high temperature sources near system, cartridges, plas-

tic fittings or plastic plumbing.

• Do not install in direct sunlight or outdoors.

• Ensure all tubing and fittings are secure and free of leaks.

• The disposable filter cartridge MUST be replaced every 12 months, at the rated capac-

ity or sooner if a noticeable reduction in flow rate occurs.

1. Safety Instructions

804984 - SP_Zip KXF 2.1 Fine lter - 11.22 v1.0 Page 7 of 16

This instruction is for the replacement of the filter in the Zip HydroTap product

where the filter is mounted internally. In preparation for your filter flushing, ensure

you have a 10 litre container available.

Some water may drip from the filter head (socket) during replacement. Keep a

towel handy to dry up any drips.

Change the Filter:

1. Go to filter flush in the menu, this isolates the water supply. Variations apply

depending on the product. Refer to individual instruction.

2. Relieve system pressure via the filter flush stop cock, a quick open and close will

do. Use the bucket to catch the discharge.

3. Grasp filter cartridge, rotate the cartridge a quarter turn to the left and gently

pull down.

Caution: a small amount of water will drip as the cartridge is removed.

4. Do not tilt the cartridge as water may spill from it if tilted.

5. Unpack replacement cartridge, write today’s date where shown on the label and

remove the sanitary cap.

6. Avoid touching the filter O-rings and filter opening as this may cause bacterial

contamination of the cartridge.

7. Push the new cartridge in and up into the filter head.

8. Turn the cartridge a quarter turn to the right until the cartridge comes to com-

plete stop and is locked into position.

9. Locate the filter flush hose situated behind the filter cartridge and direct the

hose into a container ready for flushing. Open the filter flush stop-cock. On the

menu press Adjust or Start, this will start the water flow, flushing the cartridge.

Allow at least 10 litres of water through the cartridge before use, to activate

the filter. Isolate the filter flush stop-cock and re-fit behind the filter cartridge.

Now stop filter flush or press filter flush off to stop the flow. (It may take

approximately 3 minutes to flush the 10 litres.)

10.Wipe up any spills and dispose of spent filter cartridge and packaging thought-

fully.

11. Close the door to secure the appliance.

12.Reset the internal filter counter of your HydroTap unit. Follow the instructions

of the unit.

FILTER CARTRIDGE

REPLACEMENT

1. ROTATE

2. PULL DOWN

1. INSERT

2. ROTATE

REMOVE FILTER

INSERT FILTER

2. Exchange of internal filter

Page 8 of 16 804984 - SP_Zip KXF 2.1 Fine lter - 11.22 v1.0

3. Inserting & Removing Water Supply Lines from John Guest Fittings

General instructions for John Guest con-

nections

NOTE: Ensure all John Guest tube ends

are cut clean and square.

More Information

When the filter is fitted to an appliance, please refer to the appliance owner’s guide for more product specific information and

advice on how to avoid contamination from improper handling and installation.

Warranty

Zip Water Filter cartridges are not covered by standard Zip warranty as filter life may vary according to water quality and rate

of use.

4. Other information

804984 - SP_Zip KXF 2.1 Fine lter - 11.22 v1.0 Page 9 of 16

5. Filter Performance Data - 0.2 Micron

* The term “bacteriostatic” indicates that the system limits the pas-

sage or growth of bacteria that may already exist in the incoming

water. It does not mean that water leaving the system is safer to

drink than water entering the system.

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000

AS/NZS 3497

WM-0350001

Global-Mark.com.au

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi (0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentra-

tion of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for

water leaving the system, as specied in NSF/ANSI Standard 42 and 53.

System Tested and Certied by NSF International against NSF/

ANSI Standard 42 and 53 for the reduction of:

STANDARD NO.42 - STANDARD NO.53 -

AESTHETIC EFFECTS HEALTH EFFECTS

Bacteriostatic Effects Chemical Reduction

Chemical Reduction Lead

Taste & Odor Mechanical Filtration

Chlorine Cyst

Mechanical Filtration

Nominal Particulate Class I

AS/NZS 3497

WM -0350001WM -0350001

Global-Mark.com.auGlobal-Mark.com.au

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

Model Flow Rate Capacity Kit #

0.2mic KXF 2.1 ne lter 1.5S 5.678 Lpm 6813 L 93702

Page 10 sur 16 804984 - SP_Zip Filtre n KXF 2.1 - 11.22 v1.0

Contenu

. Consignes de sécurité.................................................................................

. Remplacement du filtre interne ........................................................................

Remplacez le filtre : .....................................................................................

. Insertion et retrait des conduites d’eau au niveau des raccords John Guest...................................

. Autres informations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

. Données de filtration - , micron......................................................................

804984 - SP_Zip Filtre n KXF 2.1 - 11.22 v1.0 Page 11 sur 16

• Conçu pour une utilisation en intérieur uniquement.

• Ne pas installer dans un endroit exposé à la lumière directe du soleil ou à des tempéra-

tures <4°C ou >40 °C.

• La pression d’eau de fonctionnement sécuritaire minimale est de 70kPa, maximale de

700kPa.

• Ne pas installer là où la qualité de l’eau est inconnue ou microbiologiquement dange-

reuse.

• Après une période de non-utilisation, rincez soigneusement le ﬁltre ou les réservoirs.

• Pour des raisons de sécurité, remplacez toutes les cartouches ﬁltrantes à des inter-

valles de 12 mois ou moins.

• Remplacez tout ﬁltre si le débit d’eau ralentit ou si des goûts ou des odeurs désa-

gréables apparaissent.

ATTENTION

Pour réduire le risque associé à l’ingestion de contaminants :

• Ne pas utiliser avec de l’eau microbiologiquement dangereuse ou de qualité inconnue

sans une désinfection adéquate avant ou après le système.

MISE EN GARDE

Pour réduire le risque associé aux dommages matériels dus aux fuites d’eau :

• Lisez et suivez les instructions d’utilisation avant l’installation et l’utilisation de ce sys-

tème.

• L’installation et l’utilisation DOIVENT être conformes à tous les codes de plomberie

nationaux et locaux.

• Protéger le système du gel, retirer la cartouche ﬁltrante lorsque les températures

devraient descendre en dessous de 4,4°C.

• N’installez pas le système dans des zones où les températures ambiantes peuvent

dépasser 43°C.

• Ne pas installer sur les conduites d’alimentation en eau chaude. La température maxi-

male d’entrée d’eau est de 38°C.

• N’utilisez pas de chalumeau à gaz ou d’autres sources de haute température à proximité

du système, des cartouches, des raccords en plastique ou de la plomberie en plastique.

• Ne pas installer en plein soleil ou à l’extérieur.

• Assurez-vous que tous les tuyaux et raccords sont sécurisés et exempts de fuites.

• La cartouche ﬁltrante jetable DOIT être remplacée tous les 12 mois, lorsque la capacité

nominale est atteinte ou plus tôt si une réduction sensible du débit est constatée.

1. Consignes de sécurité

Page 12 sur 16 804984 - SP_Zip Filtre n KXF 2.1 - 11.22 v1.0

Cette instruction concerne le remplacement du filtre du produit Zip HydroTap dans

lequel le filtre est monté à l’intérieur. En préparation du rinçage de votre filtre,

assurez-vous d’avoir un bidon de 10 litres disponible.

De l’eau peut s’écouler de la tête de filtre (douille) lors du remplacement. Gardez

une serviette à portée de main pour sécher les gouttes.

Remplacez le filtre :

1. Allez dans le menu sur Rinçage du filtre pour isoler l’arrivée d’eau. Selon le pro-

duit, il y a des différences. Voir le mode d’emploi de l’appareil concerné.

2. Relâchez la pression du système via le robinet d’arrêt de rinçage du filtre, une

ouverture et une fermeture rapides suffiront. Utilisez le seau pour récupérer

l’eau qui s’écoule.

3. Saisissez la cartouche filtrante, tournez la cartouche d’un quart de tour vers la

gauche et tirez doucement vers le bas.

Attention : une petite quantité d’eau résiduelle peut s’écouler.

4. N’inclinez pas la cartouche car de l’eau pourrait s’écouler.

5. Déballez la cartouche de rechange, écrivez la date du jour à l’endroit indiqué sur

l’étiquette et retirez le capuchon hygiénique.

6. Évitez de toucher les joints toriques du filtre et l’ouverture du filtre car cela

pourrait entraîner une contamination bactérienne de la cartouche.

7. Poussez la nouvelle cartouche vers l’intérieur et vers le haut dans la tête de

filtre.

8. Tournez la cartouche d’un quart de tour vers la droite jusqu’à ce que la car-

touche s’arrête complètement et s’enclenche.

9. Prenez le tuyau de rinçage du filtre qui se trouve derrière la cartouche filtrante,

et introduisez le tuyau dans un seau. Ouvrez le robinet d’arrêt du rinçage du

filtre. Appuyez dans le menu sur Régler ou Démarrer (Adjust ou Start) pour

démarrer le débit d’eau et rincer le filtre. Laissez passer au moins 10 litres d’eau

à travers la cartouche avant utilisation, pour activer le filtre. Fermez le robinet

d’arrêt du rinçage du filtre et remettez-le en place derrière la cartouche fil-

trante. Maintenant, arrêtez le rinçage du filtre ou appuyez sur «Arrêt du rinçage

du filtre» pour arrêter l’écoulement. (Cela peut prendre environ 3 minutes pour

vider les 10 litres.)

10.Essuyez tout déversement et jetez soigneusement la cartouche filtrante usagée

et l’emballage.

11. Fermez la porte pour sécuriser l’appareil.

12.Réinitialisez le compteur du filtre interne de votre unité HydroTap. Pour ce faire,

suivez les instructions de l’appareil.

CARTOUCHE DE FILTRE

REMPLACEMENT

1. TOURNER

2. TIRER VERS

LE BAS

1. INSÉRER

2. TOURNER

RETIRER LE FILTRE

INSÉRER LE FILTRE

2. Remplacement du filtre interne

804984 - SP_Zip Filtre n KXF 2.1 - 11.22 v1.0 Page 13 sur 16

3. Insertion et retrait des conduites d’eau au niveau des raccords John Guest

Instructions générales pour les connexions

John Guest

REMARQUE : Assurez-vous que toutes

les extrémités des tubes John Guest sont

coupées proprement et d’équerre.

Plus d’information

Lorsque le filtre est installé sur un appareil, veuillez vous référer au mode d’emploi de l’appareil pour plus d’informa-

tions spécifiques au produit et des conseils sur la façon d’éviter la contamination due à une mauvaise manipulation et

installation.

Garantie

Les cartouches de filtre à eau Zip ne sont pas couvertes par la garantie Zip standard car la durée de vie du filtre peut

varier en fonction de la qualité de l’eau et du taux d’utilisation.

4. Autres informations

Page 14 sur 16 804984 - SP_Zip Filtre n KXF 2.1 - 11.22 v1.0

5. Données de filtration - 0,2 micron

* Le terme « bactériostatique » indique que le système limite le pas-

sage ou la croissance des bactéries qui peuvent déjà exister dans

l’eau entrante. Cela ne signifie pas que l’eau sortant du système est

plus sûre à boire que l’eau entrant dans le système.

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000

AS/NZS 3497

WM-0350001

Global-Mark.com.au

SPÉCIFICATIONS DE FONCTIONNEMENT

• Exigence de pression : 10 -125 psi (0,7 - 8,6 bar), sans

choc

• Température : 35 -100 °F (2-38 °C)

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

PERFORMANCE EN MATIÈRE DE RÉCLAMATION SANTÉ CERTIFIÉE PAR NSF

Ce système a été testé selon les normes NSF/ANSI 42 et 53 pour la réduction des substances listées ci-dessous. La

concentration des substances indiquées dans l’eau entrant dans le système a été réduite à une concentration inférieure

ou égale à la limite autorisée pour l’eau sortant du système, comme spécifié dans les normes NSF/ANSI 42 et 53.

Système testé et certié par NSF International selon les normes

NSF/ANSI 42 et 53 pour la réduction de :

NORME N°42 - NORME N°53 -

EFFETS ESTHÉTIQUES EFFETS SUR LA SANTÉ

Effets bactériostatiques Réduction chimique

Réduction chimique Plomb

Goût et odeur Filtration mécanique

Chlore Kyste

Filtration mécanique

Classe particulaire nominale I

AS/NZS 3497

WM -0350001WM -0350001

Global-Mark.com.auGlobal-Mark.com.au

FILTER PERFORMANCE DATA SHEET

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF

This system has been tested according to NSF/ANSI Standards 42 and 53 for

the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving the system, as specified

in NSF/ANSI Standards 42 and 53.

Substance

Influent

Challenge

Concentration

Average

Influent

Concentration

Maximum

Acceptable

Value‡

Maximum

Permissible Water

Concentration

Reduction

Requirements

Average

Effluent

Concentration

Average

Reduction

STANDARD 42  AESTHETIC EFFECTS

Chlorine 2.0 mg/L ± 10% 2 mg/L 4 mg/L /

5 mg/L ≥ 50% 0.05 mg/L 97.4%

Particulate Class I

particles 0.5 to <5μm at least 10,000

particles / mL 6,433,333/L ≥ 85% 47,388/L 99.3%

Bacteriostatic Unit passes NSF Std. 42 for Bacteriostatic effects.

STANDARD 53  HEALTH EFFECTS

Cyst Minimum 50,000 / L 99.9% /

<1/100 L 99.95% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.155 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.001 mg/L 98.9%

Lead 6.5 0.15 mg/L ± 10% 0.147 mg/L 0.015 mg/L /

0.01 mg/L 0.010 mg/L 0.0005 mg/L 99.3%

*Tested using flow rate = 1.0 gpm; pressure = 60 psig ± 3; pH = 7.5 ± 0.5; temp. = 20° ± 3°C

‡ United States Environmental Protection Agency (USEPA) Safe Drinking Water Act / New Zealand Ministry of Health Drinking-water Standards for New Zealand

ZIP 1ZLS, ZENITH 1NZLS, BIRKO 1.5BLS, ZIP 1.5ZLS,

ZENITH 1.5NZLS, ZIP 2ZLS, ZENITH 2NZLS, INSTANTA 1.5INLS

This appliance meets the domestic water treatment appliance Standards

AS/NZS 3497 and AS/NZS 4348 for the following water process:

Class Treatment Type Function Pass

IMicrobiological Status

Bacteriostatic Will stop bacteria increasing, but will

not remove unless II(a) is passed.



II Microbiological Treatment

II (a) Bacteria Removal Will remove or inactivate bacteria. N/A

II (b) Virus Removal Will remove or inactivate virus. N/A

II (c) Protozoa Removal

Cryptosporidium

and

Giardia

Will not remove or inactivate bacteria

unless II(a) and II(b) are passed.



III Particulate Reduction Reduces cloudiness. 

IV Taste and Odour Reduction Reduces tastes and odours. 

V Chemical Treatment Decreases certain chemicals:

– Lead 

Legend: = Pass N/A = Not Applicable

System Tested and Certified by NSF International against

NSF/ANSI Standard 42 and 53 for the reduction of:

STANDARD NO. 42 

AESTHETIC EFFECTS

Bacteriostatic Effects

Chemical Reduction

Taste & Odor

Chlorine

Mechanical Filtration

Nominal Particulate Class I

STANDARD NO. 53 

HEALTH EFFECTS

Chemical Reduction

Lead

Mechanical Filtration

Cyst

GENERAL INSTALLATION / OPERATION /

MAINTENANCE REQUIREMENTS

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush to drain for five (5) minutes at full flow.

• Replace cartridges when capacity is reached or

when flow becomes too slow, but at least annually.

• For cold water use only.

• Product must be installed with a backflow prevention

device in accordance with AS/NZS 3500.1.2 and

AS/NZS 2845.1

OPERATING SPECIFICATIONS

• Pressure requirement: 10 -125 psi

(0.7 - 8.6 bar), non-shock

• Temperature: 35 -100°F (2-38°C)

Model Flow Rate Capacity

1Z-LS 3.75 Lpm 4163 L

1.5Z-LS 5.678 Lpm 6813 L

2Z-LS 5.678 Lpm 9463 L

1NZ-LS 3.75 Lpm 4163 L

Model Flow Rate Capacity

1.5NZ-LS 5.678 Lpm 6813 L

2NZ-LS 5.678 Lpm 9463 L

1.5B-LS 5.678 Lpm 6813 L

1.5IN-LS 5.678 Lpm 6813 L

SPECIAL NOTICES

• Installation instructions, parts and service availability, and

standard warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter

cartridges.

• Do not use with water that is microbiologically unsafe, or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by

this water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions as specified

above. Actual performance may vary depending on influent

water conditions.

The term "bacteriostatic" indicates that the system limits the

passage or growth of bacteria that may already exist in the

incoming water. It does not mean that water leaving the system

is safer to drink than water entering the system.

EPA Est. NO. 00263-IL-002

Manufactured for Zip by Pentair Everpure

1040 Muirfield Drive

Hanover Park, IL 60133 USA,

630.307.3000 AS/NZS 3497

WM-0350001

Global-Mark.com.au

Modèle Débit Capacité Article #

0.2mic KXF 2.1 ltre n 1.5S 5.678 l/min 6813 L 93702

All components are

FDA CFA compliant

Technische Änderungen, Änderungen der Ausführung und Irrtum vorbehalten. Subject to technical changes, design changes and errors. Sauf

modifications techniques, changements constructifs et erreur ou omission.

9120-34435 11.22

CLAGE GmbH

Pirolweg 4

21337 Lüneburg

Deutschland

Telefon: +49 4131 8901-0

E-Mail: [email protected]

Internet: www.clage.de

*9120-34435*

Table of contents

Languages:

Other clage Water Filtration System manuals

clage

clage Zip HydroTap G5 B 60 User manual

clage

clage Zip HydroTap G5 BCS 20 User manual

Popular Water Filtration System manuals by other brands

Hydac

Hydac Filtromat OF5F Operating and maintenance instructions

Pentair

Pentair THS Series Installation and user guide

Steinbach

Steinbach 040380 instruction manual

RZ AIRflow

RZ AIRflow 10048 user guide

HQUA

HQUA UV Water Sterilizer instruction manual

SuperFish

SuperFish Pond Skim 2000 quick start guide

H2O International

H2O International Guard U1000 Installation instructions manual

AlkaWay

AlkaWay UltraStream user manual

Katadyn

Katadyn PowerSurvivor 40E owner's manual

VGE

VGE FLEX UV-C manual

EHEIM

EHEIM 2048 manual

AQUAPHOR

AQUAPHOR DWM-101 installation guide

TLV

TLV SF1 instruction manual

Doulton

Doulton Ceramic Twin Undersink Installation & maintenance guide

Purwater

Purwater PW-RO4L Installation and operating instructions

Spear & Jackson

Spear & Jackson BoilerMag XC BMXC22 Installation & maintenance

VGE

VGE Blue Lagoon PRO UV-C 75W manual

Volth

Volth ARGO HYTOS DG 041 installation manual

clage Zip KXF 2.1 User manual

Popular Water Filtration System manuals by other brands