Clarion VRX765VD User manual

VRX765VD
VRX766VD
-1-
Service Manual
Published by Service Dept.
Printed in Japan
ClarionCo.,Ltd.
50Kamitoda,Toda-shi,Saitama335-8511 Japan
ServiceDept.: 5-66 Azuma ,Kitamoto-shi, Saitama 364-0007 Japan
Tel:[phone] / 2432 FAX:[phone]
298-6351-00 Mar.2006
Model
DVD Multmedia Station with Touch
Panel Controller
(QC-6823K-B)
(NTSC/ Region No. "3")
(QC-6823K-A)
(PAL/ Region No. "3")
(QC-6823B-A)
(NTSC/ Region No. "1")
Model
Model
SPECIFICATIONS
FM tuner section
Frequency range: 87.9MHz to 107.9MHz(B-A)
87.0MHz to 108.0MHz(K-A,B,C)
Usable sensitivity: 9dBf
50dB quieting sensitivity:
15dBf
Alternate channel selectivity:
70dB
Stereo separation: 35dB(1kHz)
Frequency response: 30Hz to 15kHz(+3/-3dB)
AM tuner section
Frequency range: 530kHz to 1710kHz(B-A)
531kHz to 1629kHz(K-A,B,C)
Usable sensitivity: 28dBu
DVD player section
System: Digital versatile disc system with
CDDA capable
Usable discs: DVD video disc,Compact disc
Frequency response: 20Hz to 20kHz(CD)(+1/-1dB)
Dynamic range: 100dB(1kHz)
Distortion: 0.01%
MP3 / WMA section
MP3 Sampling rate: 11.025kHz to 48kHz
MP3 Bit rate: 8kbps to 320kbps/VBR
WMA Bit rate: 48kbps to 192kbps
Logical Format: ISO9660 level1, 2
JOLIET or Romeo
Audio amplifier section
Maximum power output:200W(50W x 4ch)
Rate power output: 14w X4ch
at 20 Hz to 20kHz,1%,4 ohm
(QC-6823K-A,B,C)
Power output: 19W x 4 at 4 ohm
and 1 % THD+N (CEA-2006)
(QC-6823B-A)
Speaker impedance: 4 ohm(4 to 8 ohm)
(QC-6823K-C)
(PAL/ Region No. "4")
Model

VRX765VD
VRX766VD -2-
Input section
Video input: 1.0V+0.2/-0.2Vp-p
(input impedance 75 ohm)
Audio input: 130mV+60/-60mVrms(High)
600mV+80/-80mVrms(Mid)
840mV+100/-100mVrms(Low)
(input impedance 10k ohm or
greater)
Video output section
Video output: 1.0V+0.2/-0.2Vp-p(output imped-
ance 75 ohm)
LCD monitor section
Screen size: 7-inch wide type
(152mm Width x 85mm Height)
Display method: Transmission type TN liquid
crystal display
Drive method: TFT(thin-film transistor) active
matrix driving
Pixels: 336,960(1440x234)
General
Power source voltage: 14.4V DC
(10.8 to 15.6V allowable)
Ground: Negative
Current consumption: 4.0A(1W)
Auto antenna rated current:
500mA less
Dimensions(mm): Main unit
178(W)x50(H)x165(D)
Remote control unit
54(W)x28.8(H)x155(D)
Weight: Main unit 2.4kg
Remote control unit 100g
(including battery)
* Specifications comply with JEITA Standards.
* CEA-2006:New standard of Consumer Electronics As-
sociation.
* Specifications and design are subject to change without
notice for further improvement.
NOTES
* As for this model, the tuner of the DSP type is used.When
you exchange it due to the tuner pack(BL1:880-2091C)
trouble, it is necessary to adjust for S-meter etc.Special
JIG is necessary for an accurate adjustment.The proce-
dure document for the exclusive use jig is appended to
it.
* This DSP IC SAF7730H(051-6706-10) of main PWB is
exposed die soldering pad type.
The middle of this IC package is soldered with the main
PWB, and it cannot remove in an ordinary soldering iron.
Please use special removal JIG at the time of IC ex-
change.
* We cannot supply PWB with component parts in prin-
ciple. When a circuit on PWB has failure , please repair
it by component parts base. Parts which are not men-
tioned in service manual are not supplied.
* This DVD player can play the following discs.
DVD video discs,Video CDs,CD text,Audio CDs.
* This DVD video player cannot playback DVD-
Audio,DVD-RAM,Photo CDs,etc.
* This unit can play back CD-R/CD-RW,DVD-R/RW discs
on which MP3/WMA music data have been recorded..
This unit is a ID3 Tag compatible model.
This unit supports the title,artist and album display of
the ID3 Tag versions 1 and 1.1.
After disc loading,the play mode is automatically en-
gaged.
* This product incorporates copyright protection technol-
ogy that is protected by U.S. patents and other intellec-
tual property rights .
Use of this copyright protection tecnology must be au-
thorized by Macrovision, and is intended for home and
other limited viewing uses only unless otherwise autho-
rized by Macrovision.
Reverse engineering or disassembly is prohibited.
* The DVD video system assigns a region number to DVD
video players and DVD discs by sales area.
The DVD video region number is marked on the disc
jacket.
* This product includes technology owned by Microsoft
Corporation and cannot be used or distributed without a
license from MSLGP.
* Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby
Laboratories.
* "DTS" and "DTS Digital Out" are trademarks of Digital
Theater Systems,Inc.
* "iPod" is for legal or righthoder-authorized copying
only.Do not steal music.
COMPONENTS
QC-6823B-A,K-A,K-B
Main unit ----------- 1
Remote control unit RCB-177-200 1
Batteries(AA.SUM-3) ----------- 2
Universal mounting bracket 300-9035-01 1
DCP case 335-6035-60 1
Power supply lead(18P) 854-6420-50 1
Outer escutcheon 940-8145-00 1
Parts bag -----------
Electro tap 060-0018-00 1
Machine screw(M4 x3) 714-4003-8H 4
Flat head screw(M5 x8) 714-5008-4B 4
Sems hex. bolt(M5 x8) 716-0496-501 5
Parts bag -----------
Hook plate 330-8216-01 2
Cord clamp 335-0833-01 1
Rubber cap 345-3653-01 1
Screw(M5 x10) 716-0726-51 1
Parts bag -----------
Pad screw(M1.7 x5 Blk) 716-0872-52 1
Parts bag -----------
RCA CAP 345-3799-20 12

VRX765VD
VRX766VD
-3-
1. Use specified parts.
The system uses parts with special safety features against fire
and voltage. Use only parts with equivalent characteristics
when replacing them.
The use of unspecified parts shall be regarded as remodeling
for which we shall not be liable. The onus of product liability
(PL) shall not be our responsibility in cases where an accident
or failure is as a result of unspecified parts being used.
2. Place the parts and wiring back in their original positions after
replacement or re-wiring.
For proper circuit construction, use of insulation tubes, bond-
ing, gaps to PWB, etc, is involved. The wiring connection and
routing to the PWB are specially planned using clamps to keep
away from heated and high voltage parts. Ensure that they are
placed back in their original positions after repair or inspec-
tion.
If extended damage is caused due to negligence during re-
pair, the legal responsibility shall be with the repairing com-
pany.
3. Check for safety after repair.
Check that the screws, parts and wires are put back securely
in their original position after repair. Ensure for safety reasons
there is no possibility of secondary ploblems around the re-
paired spots.
If extended damage is caused due to negligence of repair, the
legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the parts
for the automobile.
Disconnect the battery terminal after turning the ignition key
off. If wrong wiring connections are made with the battery con-
nected, a short circuit and/or fire may occur. If extensive dam-
age is caused due to negligence of repair, the legal responsi-
bility shall be with the repairing company.
5. Cautions in soldering
Please do not spread liquid flux in soldering.
Please do not wash the soldering point after soldering.
6. Cautions in soldering for chip capacitors
Please solder the chip capacitors after pre-heating for replace-
ment because they are very weak to heat.
Please do not heat the chip capacitors with a soldering iron
directly.
7. Cautions in handling for chip parts.
Do not reuse removed chips even when no abnormality is ob-
served in their appearance. Always replace them with new
ones. (The chip parts include resistors, capacitors, diodes, tran-
sistors, etc).
Please make an operation test after replacement.
8. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the iron
tip temperature is around 270 . Take care not to apply the
iron tip repeatedly(more than three times)to the same patterns.
Also take care not to apply the tip with force.
9. Turn the unit OFF during disassembly and parts replacement.
Recheck all work before you apply power to the unit.
10.Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through the
lens of the optical pickup. When checking that the laser opti-
cal diode lights up, keep your eyes more than 30cms away
from the lens. Prolonged viewing of the laser within 30cms
may damage your eyesight.
11.Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by elec-
trostatic charge caused by your clothes and body. Make sure
to avoid electrostatic charges on your clothes or body, or dis-
charge static electricity before handling the optical pickup.
11-1. Laser diode
The laser diode terminals are shorted for transportation in or-
der to prevent electrostatic damage. After replacement, open
the shorted circuit. When removing the pickup from the mecha-
nism, short the terminals by soldering them to prevent this
damage.
11-2. Actuator
The actuator has a powerful magnetic circuit. If a magnetic
material is put close to it. Its characteristics will change. En-
sure that no foreign substances enter through the ventilation
slots in the cover.
11-3. Cleaning the lens
Dust on the optical lens affects performance.
To clean the lens, apply a small amount of isopropyl alcohol to
lens paper and wipe the lens gently.
To engineers in charge of repair or
inspection of our products.
Before repair or inspection, make sure to follow the
instructions so that customers and Engineers in charge
of repair or inspection can avoid suffering any risk or
injury.
QC-6823B-A
CAUTIONS
Use of controls,adjustment or performance of procedures
other than those specified herein,may result in hazardous
radiation exposure.
The compact disc player should not be adjusted or repaired
by anyone except properly qualified service personnel.

VRX765VD
VRX766VD -4-
SYSTEM CONNCTION
VRX765VD/VRX766VD
CeNET
SLAVE STAND
ALONE
(VCZ625)
(DVH940)
(TTX7501z/TTX7504z)
(SRK5)
(SRV303)
(DCZ625)
TV Tuner
CeNET cable
(included
the TV tuner)
RCA video cable
(included the TV tuner)
CeNET DVD Changer
5.1 ch Surround
Decoder
CeNET cable
(included the
DVH940)
Front
Speakers
4-Channel
Amplifier
Rear
Speakers
Center speaker
built-in amplifier
Powered sub-woofer
built-in amplifier
(Black)
Digital optical fiber cable (included the DVH940)
RCA cable
(sold separately)
RCA cable
(sold separately)
RCA cable (sold separately)
Digital optical fiber cable
(DCA-005/008 ,sold separately)
Set the [SLAVE/STAND ALONE]
switch to the [SLAVE] position.
Set the [CeNET/STAND ALONE] switch
to the [CeNET] position.
(Gray)
(Gray)
RCA video cable (included the VCZ625)
Ferrite clamp
(Included the
DVD changer)
RCA cable
(included
the DVH940)
Red
White
Non fader
output
CeNET Cable
(included the Changer)
Satellite Radio
Receiver
CeNET cable
(included the SIRIUS)
*XM ; sold separately
CeNET Y-adapter
(CCA-519-601,
sold separately)
CeNET CD Changer
Video
Selector
Yellow
Purple
STAND
ALONE
ERROR DISPLAYS
If an error occurs,one of the following displays is displayed.Take the measures described below to eliminate the problem.
DVD
player
CD
changer
Error display
ERROR 2
ERROR 3
ERROR 6
ERROR 2
ERROR 3
ERROR 6
Cause
A CD is caught inside the CD deck and
is not ejected.
A CD cannot be played due to
scratches,etc.
A CD is loaded upside-down inside the
CD deck and does not play.
A CD inside the CD changer is not
loaded.
A CD inside the CD changer cannot be
played due to scratches,etc.
A CD inside the CD changer cannot be
played because it is loaded upside-down.
Measure
This is a failure of CD deck's mechanism
and cinsolt your store of purchase.
Replace with a non-scratched,non-
warped disc.
Eject the disc then reload it properly.
This is a failure of CD changer's mecha-
nism.
Replace with a non-scratched,non-
warped disc.
Eject the disc then reload it properly.
Note:If an error display other than the ones described above appears, press the reset button.
* When the reset button is pressed,frequencies of TV/radio stations,titles,etc. stored in memory are cleared.

VRX765VD
VRX766VD
-5-
WIRE CONNECTION
CeNET
terminal
Red
White
Red
White
Right
left Front audio output
terminal
Right
left Rear audio output
terminal
Right
left
Non fader
output terminal
Gray
Black
Purple Red
White
Yellow
Yellow
Yellow
White
Red
Video output terminal
TV tuner input terminal or
DVD changer input terminal
Video
Audio (left)
Audio (right)
Visual input
terminal
Optical output
connector
Radio antenna jack
Wireless
Head phone
VTR etc.
4-Channel Amplifier
Right
Left
(2-ZONE
output terminal)
Gray Rear monitor
Black
Red
Green
Red
White
Yellow
Black
Purple
Purple/Black
Grass-green
Gray
Gray/Black
White
White/Black
Green
Green/Black
Blue/White
Orange/White
Red
Brown
Blue
(+12V main power)
Ground
Rear right +
Rear right -
Parking brake lead
Front right +
Front right -
Front left -
Rear left +
Rear left -
Amp. turn-on lead
Illumination
+12V accessory
Phone mute
Auto antenna
iPod
(CCA-670-600)
Connector cab le
20
2 4 6 8
1 3 5 7 9 19
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
LEFT REAR
RIGHT REAR
LEFT FRONT
RIGHT FRONT
S-GND
S-GND
NF LEFT
NF RIGHT
S-GND
S-GND
2ZONE LEFT
2ZONE RIGHT
V OUT GND
V IN GND
VIDEO OUT
VIVEO IN
V-AUDIO GND L
V-AUDIO GND R
V-AUDIO LEFT
V-AUDIO RIGHT
10 12 14 16 18
11 13 15 17
12
10
11 12
13 14
15 16
8
7
6
5
4
3
9
Front left +
10
J601
No. Description No. Description
1 SP R/L(+)
3 SP F/L(-)
5 SP F/L(+)
7 SP F/R(+)
9 SP F/R(-)
11 SP R/R(+)
13 SP R/R(-)
15 BACK UP
2 SP R/L(-)
4 PHONE MUTE
6 ACC
8 AUTO ANT
10 REMOTE
12 ILLUMI
14 PARKING BRAKE
16 GND
P201
Description
No.
No. Description
BACK UP

VRX765VD
VRX766VD -6-
BLOCK DIAGRAM
Main unit section

VRX765VD
VRX766VD
-7-
ADJUSTMENTS
*Refer to the printed circut board(47,50 or 51 pages)for
an adjustment point and VR.
*The NTSC (K-A:PAL)composite output signal of the sig-
nal generators of adjustment is performed with the fol-
lowing output.Video input of visual mode.
A image signal: 714mV
A synchronized signal: 286mV
Sub PWB section
1. Confirm the power supply voltage
Input signal: 10-steps wave
Measurement is performed by composite screen
display.It measures by digitalbolt meter and DIMMER is
100%.
1-1.Adjust VR551 so that voltage of TP593 is 5.30 +0.02/-
0.02V.
Caution: A LCD controller will be damaged if the voltage
beyond 5.45V is added.
1-2.Confirm that TP556 is 3.3 +0.2/-0.2V
1-3.Confirm that TP558 is 7.5 +0.2/-0.2V
1-4.Confirm that TP559 is 18.5 +0.8/-0.8V
1-5.Confirm that TP555 is -12.0 +0.5/-0.5V
LCD PWB section
2. Confirm the PLL lock
Input signal: 10-steps wave
2-1.It checks that see a screen and 10 gradation display do
not have a synchronous flow.
After checking and uniting the freerun frequency of item
9.when the synchronoization cannot be taken.
3. BRIGHT voltage adjustment
Input signal: 10-steps wave
Mesurement is performed by composite screen display.
It measures by digital bolt meter.
3-1.Adjust VR804(BRIGHT) so that the voltage of
TP805(BRIGHT) will become 2.00 +0.02/-0.02V.
4. RGB-AMP adjustment (black-black)
Input signal: 10-steps wave
Measurement is performed by composite screen display.
It measures with an oscilloscope.
4-1.Adjusts VR805 so that the black-black level (V B-B) of
the waveform of TP861 (G) will become 4.0 +0.1/-0.1V.
(Refer to Fig. 1)
5. Contrast adjustment (black-white)
Input signa: 10-steps wave
Measurement is performed by composite screen display.
It measures with an oscilloscope.
5-1.Adjusts VR801 so that the black-black level (V B-w) of
the waveform of TP861 (G) will become 3.8 +0.1/-0.1V.
(Refer to Fig. 1)
6. Gamma voltage check
Input signal: 10-steps wave
Measurement is performed by composite screen display.
It measures with an oscilloscope.
6-1.Confirm the waveform of TP861(LCD G) that ten grada-
tion has come out.
6-2.It checks that it is the 3rd gradation is 2.3+0.2/-0.2V.
6-3.Confirm that TP806(Gamma 0) is 2.30 +0.20/-0.20V
6-4.Confirm that TP807(Gamma 2) is 2.13 +0.20/-0.20V
7. White balance adjustment
Input signal: 10-steps wave
Measurement is performed by composite screen display.
It measures DC range of an oscilloscope.
*Are careful in order to perform correctly white balance
adjustment.
*1. The range of CH1,CH2 of an oscilloscope is used as 1V
range.
*2. CH1,CH2 are indicated by GND and GND is united. (Re-
fer to Fig. 2)
7-1.White balance red adjustment
7-1-1.The waveform of TP861 is displayed on CH1 of an
oscilloscope, and the waveform of TP862(LCD-R) is dis-
played on CH2.
7-1-2.Adjust VR802(BRT-R) so that the waveform of
TP862(LCD-R) will become the same as the waveform
of TP861.
7-2.White balance blue adjustment
7-2-1.The waveform of TP861 is displayed on CH1 of an
oscilloscope, and the waveform of TP860(LCD-B) is dis-
played on CH2.
7-2-2.Adjust VR803(BRT-B) so that the waveform of
TP860(LCD-B) will become the same as the waveform
of TP861.
8. VCOM AC adjustment
Input signal: 10-steps wave
Measurement is performed by composite screen display.
It measures with an oscilloscope.
8-1.Adjust the VR806(VCOM AC) so that amplitude of a
waveform of TP852(VCOM AC) is 7.0+0.1/-0.1V.
There are no abnormalities, such as distortion, in a wave-
form.
CH1
CH2
(KI2
(KI1

VRX765VD
VRX766VD -8-
9. Free run frequency adjustment
Input signal: 10-steps wave
Measurement is performed by composite screen display.
It measures by frequency counter and DIMMER is 100%.
9-1.Adjust VR941 so that the frequency of TP949 will be-
come to 15.734kHz+10/-10Hz.
*TP804 is made to short-circuit to GND. It checks that
the voltage of TP951 is 1.61+0.20/-0.20V at this time.
And checks that the voltage of TP952 is same.
10.PAL burst cleaning coil adjustment
Input signal:The color bar signal of PAL.
It measures with an oscilloscope etc.
10-1.Adjust L803 coil so that change TP860(LCD-B) of a
color waveform may be lost.
11.BRT/COL/HUE check
Input signal: Split color bar signal
11-1.Comfirm that the color bar is normally displayed at state
to begin.
11-2.Comfirm that the BRT/COL/HUE control is moved
screen.
11-3.Comfirm the superimposition display is normally.
12.V-MUTE check
Input signal:Split color bar signal
12-1.Comfirm a composite video screen is mute of V-
MUTE:"H" .
13.Wide mode check
Input signal:Split color bar signal
13-1. Comfirm a wide mode changed screen(Full wide /Wide
/Cinema /Normal).
14.Screen position check
Input signal: Mono-sucpeo signal.
14-1.Comfirm that the screen is displayed in the center by
mono-scope display (Video mode).
14-2.Comfirm that the screen is displayed in the center by
radio screen display (RGB mode).
15.Synchronicity condition check
15-1.Comfirm a normal display by DVD playback (main
menu) of HITOMI.
16.Key sw operation/Illum check
16-1Comfirm that key operation can be performed.
16-2Comfirm the key illum lighting .
17.Back light check
Power supply voltage: 13.2V
DIMMER=100%
17-1.Comfirm the TP962 freqency is 63kHz +5/-5kHz.
17-2.Comfirm the TP961 voltage is 5.2V +0.5/-0.5V.
17-3.Comfirm the light on at the power supply voltage to
10V.
17-4.Comfirm check at DIMMER control changes so that
brightness changes.
18.VCOM-DC check
Input signal:10-steps wave
Measurement is performed by composite screen display.
18-1.Adjust VR807(VCOM DC) so that a screen flicker may
become the minimum.
Main PWB section
19.TV delay time adjustment
Adjustment is performed in TV mode and the stable chan-
nel which does not have disorder in a screen is used.
It acts as the monitor of the signal of TP329 (Normal
horizontal synchronous input) and TP421 (Delay output
synchronization).
19-1.To falling of the Horizontal Synchronizing signal of
TP329, VR401 is adjusted so that falling of TP421 may
be overdue 3.50 +0.1/-0.1 uS
19-2.Confirm that Low level time of TP421 is 4.7 +0.7/-0.7uS.
19-3.It checks whether there is any gap in the right-and-left
balance of a superimposition display to TV image, or the
character has not passed by the end after the adjust-
ment.
Recommends connected TV tuner :TTX7501Z(ZT-
4620B-A) for NTSC,:TTX7504Z(ZT-4610K-A) for PAL(s).
20.S-meter adjustment of BUS-tuner
The adjustment data is written in the memory of
EEPROM(IC502).The special jig and software are nec-
essary for BUS-TUNER adjustment.
* CeNET-analyzer
* Windows installed Personal computer
* SSG
* Adjustment-Software(Ver.Y4-S009-513-20051111)
a. Installation of software in the set-folder of the writing
E2P.
b Connect CeNET-analyzer to the unit with the CeNET-
cable.
c Connect CeNET-analyzer(MASTER/SLAVE side) to the
PC with the serial crossing cable.
d Connect POWER-lead of CeNET-analyzer to the
POWER-lead of the unit.
e Connect the antenna to the unit.(FM-ANT for first ad-
justment)
f Turn on CeNET-analyzer,and press the RESET-button
of it.
20-1.Set up the software
20-1-1.Click [ADJ_DSP].
20-1-2.Click [open Comm PORT].(To open the COM port
of PC)
20-1-3.Click [Initialization of JIG].(The BUS-analyzer
sounds)
20-1-4.Click [Incoming connection].(The unit is recognized
to the BUS-analyzer)
The data is displayed, and the display changes regu-
larly.
20-2.PRN data writing / Set up FM-IF-Offset data
20-2-1.Click [Initial EEPROM with CS 16], and select PRN-
FILE.
The PRN-data is write in EEP-ROM of the unit.
20-2-2.Confirm "OK" display after writing of data.
20-2-3.Click [Setting-prn] under "FM IF-COUNT".(the writ-
ten FM-IF-Offset data becomes effective.)
20-3.Adjustments FM S-meter
20-3-1.Set SG output to 65dBuV.(FM)
20-3-2.Click [Adj,HI] of "FM S-Meter".(Wait until the value
stops.)

VRX765VD
VRX766VD
-9-
20-3-3.Set SG output to 55dBuV.(FM)
20-3-4.Click [Adj,LO] of "FM S-Meter".(Wait until the value
stops.)
20-3-5.Click [Check].If the display is not within +/-0.5dBuV
of ANT-output level of SG, readjust with "MOD-
ON"(22.5kHz 400Hz).
20-4.Set up FM-IF-Offset data
* Exchange the antenna for "AM-ANT-dummy"
<!8>20-4-1.Click [Setting-prn] under "AM IF-COUNT".(The
AM-IF-Offset data of EEPRON is effective.)
20-4-2.Click [Check], and confirm the display is within +/-
500.0.
20-5.Adjustments AM S-meter
20-5-1.Set SG output to 70dBuV.(AM)
20-5-2.Click [Adj,HI] of "AM S-Meter".(Wait until the value
stops.)
20-5-3.Set SG output to 40dBuV.(AM)
20-5-4.Click [Adj,LO].(Wait until the value stops.)
20-5-5.Click [Check]. If the display is not within +/-0.5dBV
of ANT-output level of SG, readjust with "MOD-ON"(30%
400Hz).
Finally, push the reset button of the unit.
When computer continues to freeze, click [RESET] of
"MENU", and readjust the lost adjustment point.IF not re-
turning, press the RESET-button of CeNET-analyzer.and
restart adjustment from the first step.
21.OSD dot adjustment
An adjustment screen is performed on the "T-PNL"
screen, or the 9th screen (five-step display) of "COLOR-
BAR" in the test mode.
Please choose the screen which is easy to adjust from
either.
21-1.The hole has opened in the Lower case and it adjusts
by VR451 mounted in the MAIN-PWB solder side.
21-2.In the case of adjustment in a T-PNL screen
It adjusts so that the white line of a 1-dot display long
may be vividly displayed.
21-3.In the case of adjustment by 9th COLOR-BAR
It adjusts so that the white line of top, the bottom and
inside may be displayed as clear white.
Slide mechanism section
23 Horizontally position
Calibration jig is used in order to memorize a horizontal
level position.
Please refer to an attached figure A.
It is made to memorize horizontally among a figure in
the position of points.
It is performing giving about 3 degrees of angles inten-
tionally.
If the MUTE button and the ISR button are pushed, a
beep sound will sound.
A calibration begins at the time.
Flow of operation
a. Slide OPEN
b. Tilt up: Memory of 110 degree position
c. Tilt down: Memory of horizontally position (Jig used)
d. Tilt up
e. Tilt down
f. Slide CLOSE
g. Calibration end




#

VRX765VD
VRX766VD -10-
051-3924-90 MD1424R DC to DC Converter
051-3925-90 OZ9910ISN-T2 Dual Forward PWM Controller
TerminalDescription
pin 1:N DRV 4 :Bottom MOSFET gate drive output in dual
forward converter.
pin 2: P GND : High-current power ground.
pin 3:N DRV 2 :Bottom MOSFET gate drive output in dual
forward converter.
pin 4: GND A : Low-current signal ground.
pin 5: CT : High frequency oscillator capacitor for oper-
ation and striking frequency.
pin 6:LCT :Low frequency timing capacitor for LPWM
dimming and striking timer.
pin 7:ADJ : Signal input for LPWM/ analog dimming.
pin 8: ENA : Enable and reset.
pin 9: V-SENSE : Transformer output over-voltage and over-
current detection.
pin 10: CMP/SST : Soft start and loop compensation capacitor.
pin 11: I-SENSE : Lamp current sensing and lamp ondetec-
tion.
pin 12: Vref : Reference voltage output.
pin 13: VIN :Supply voltage for IC.
pin 14: HSB : High side driver buffer output.
pin 15:P DRV 3 : Top MOSFET gate drive output in dual for-
ward converter.
pin 16:P DRV 1 : Top MOSFET gate drive output in dual for-
ward converter.
051-6456-00 YGV629-VZ Video display processor
TerminalDescription
pin 1: PLL VDD : - : PLL power supply.
pin 2: PLL FILTER : - : PLL filter connection.
pin 3: PLL VSS : - : PLL ground.
pin 4: NC : - : Not in use.
pin 5: PLL CTL 5 :IN: PLL multiply select.
pin 6: PLL CTL 4 :IN: PLL multiply select.
pin 7: PLL CTL 3 :IN: PLL multiply select.
pin 8: PLL CTL 2 :IN: PLL multiply select.
pin 9: PLL CTL 1 :IN: PLL multiply select.
pin 10: PLL CTL 0 :IN: PLL multiply select.
pin 11: DT CK Sel_N :IN: Display clock select.
pin 12: DT CK IN :IN: Display clock input.
pin 13: VSS : - : Digital ground.
pin 14: VDD : - : Digital power supply.
pin 15: CPU D 0 :I/O:CUP interface. Data bus.
pin 16: CPU D 1 :I/O:CUP interface. Data bus.
pin 17: CPU D 2 :I/O:CUP interface. Data bus.
pin 18: CPU D 3 :I/O:CUP interface. Data bus.
pin 19: CPU D 4 :I/O:CUP interface. Data bus.
pin 20: CPU D 5 :I/O:CUP interface. Data bus.
pin 21: CPU D 6 :I/O:CUP interface. Data bus.
pin 22: CPU D 7 :I/O:CUP interface. Data bus.
pin 23: CPU WAIT_N : O : CUP interface. Wait.
pin 24: CPU READY_N : O : CUP interface. Ready.
pin 25: CPU INT_N : O : CUP interface. Interrupt.
pin 26: VDD : - : Digital power supply.
pin 27: VSS : - : Digital ground.
pin 28: CPU CS_N :IN: CUP interface. Chip select.
pin 29: CPU WR_N :IN: CUP interface. Write command.
pin 30: CPU RD_N :IN: CUP interface. Read command.
pin 31:CPU PS 2 :IN: CUP interface. Port select.
pin 32:CPU PS 1 :IN: CUP interface. Port select.
pin 33:CPU PS 0 :IN: CUP interface. Port select.
pin 34: CPU SD OUT : O : CUP interface. Serial data output.
pin 35: CPU S D IN :IN: CUP interface. Serial data input.
pin 36: CPU S CS_N :IN: CUP interface. Serial chip select.
pin 37: CPU S CLK :IN: CUP interface. Serial clock.
pin 38: CPU SER_N :IN: CUP interface. Parallel/Serial select.
pin 39: CPU RESET_N :IN: CUP interface. Reset.
pin 40: VSS : - : Digital ground.
pin 41: VDD : - : Digital power supply.
pin 42: Memo A 0 : O : Pattern Memory interface. Address output.
pin 43: Memo A 1 : O : Pattern Memory interface. Address output.
pin 44: Memo A 2 : O : Pattern Memory interface. Address output.
pin 45: Memo A 3 : O : Pattern Memory interface. Address output.
pin 46: Memo A 4 : O : Pattern Memory interface. Address output.
pin 47: Memo A 5 : O : Pattern Memory interface. Address output.
pin 48: VSS : - : Digital ground.
pin 49: Memo A 6 : O : Pattern Memory interface. Address output.
pin 50: Memo A 7 : O : Pattern Memory interface. Address output.
pin 51: Memo A 8 : O : Pattern Memory interface. Address output.
pin 52: Memo A 9 : O : Pattern Memory interface. Address output.
pin 53: Memo A 10 : O : Pattern Memory interface. Address output.
pin 54: Memo A 11 : O : Pattern Memory interface. Address output.
pin 55: VDD : - : Digital power supply.
pin 56: VSS : - : Digital ground.
pin 57: Memo A 12 : O : Pattern Memory interface. Address output.
pin 58: Memo A 13 : O : Pattern Memory interface. Address output.
pin 59: Memo A 14 : O : Pattern Memory interface. Address output.
pin 60: Memo A 15 : O : Pattern Memory interface. Address output.
pin 61: Memo A 16 : O : Pattern Memory interface. Address output.
pin 62: Memo A 17 : O : Pattern Memory interface. Address output.
pin 63: VSS : - : Digital ground.
pin 64: Memo A 18 : O : Pattern Memory interface. Address output.
pin 65: Memo A 19 : O : Pattern Memory interface. Address output.
pin 66: Memo A 20 : O : Pattern Memory interface. Address output.
pin 67: Memo A 21 : O : Pattern Memory interface. Address output.
pin 68: Memo A 22 : O : Pattern Memory interface. Address output.
pin 69: Memo A 23 : O : Pattern Memory interface. Address output.
pin 70: Memo A 24 : O : Pattern Memory interface. Address output.
pin 71: VDD : - : Digital power supply.
pin 72: VSS : - : Digital ground.
pin 73: Memo WE_N : O : Pattern Memory interface. Write command.
+
-
Error Amp out 12
Error Amp in- 13
+
-
OSC
OSC 10
+
-
Over+ 16
Over - 15
Soft S 14
R
SQ
Dead
time
Control Low
side
Driver
High
side
Driver
1,2,22,23,24,25
Vout
3,4,5,6
VDDP GND
26
V GL 21 V GH7
Boot
strap
VB8GND 9
17
Vboot20 VCC19 Vref11
R/C (H-ON) 18 CONTROL
Thermal
shut down
Vref 12
ADJ 7
V-SENSE 9
GND A 4
CMP/SST 10
I-SENSE 11
P DRV 315
N DRV 23
HSB14
ENA8
CT5
P GND2
P DRV 116
N DRV 41
VIN13
Voltage Ref
Current Bias
LCT 6 LF OSC
LFCK
Current
Feedback
Control
Control
Logic
Voltage
Feedback
Control
3V
Feedback Control
High-side
Driver Buffer
Output
Driver
HF OSC
Protection
HFCK
EXPLANATION OF IC

VRX765VD
VRX766VD
-11-
pin 74: Memo OE_N : O : Pattern Memory interface. Output enable.
pin 75: Memo D 15 :I/O:Pattern Memory interface. Data I/O.
pin 76: Memo D 7 :I/O:Pattern Memory interface. Data I/O.
pin 77: Memo D 14 :I/O:Pattern Memory interface. Data I/O.
pin 78: Memo D 6 :I/O:Pattern Memory interface. Data I/O.
pin 79: Memo D 13 :I/O:Pattern Memory interface. Data I/O.
pin 80: Memo D 5 :I/O:Pattern Memory interface. Data I/O.
pin 81: VSS : - : Digital ground.
pin 82: VDD : - : Digital power supply.
pin 83: Memo D 12 :I/O:Pattern Memory interface. Data I/O.
pin 84: Memo D 4 :I/O:Pattern Memory interface. Data I/O.
pin 85: Memo D 11 :I/O:Pattern Memory interface. Data I/O.
pin 86: Memo D 3 :I/O:Pattern Memory interface. Data I/O.
pin 87: Memo D 10 :I/O:Pattern Memory interface. Data I/O.
pin 88: Memo D 2 :I/O:Pattern Memory interface. Data I/O.
pin 89: Memo D 9 :I/O:Pattern Memory interface. Data I/O.
pin 90: Memo D 1 :I/O:Pattern Memory interface. Data I/O.
pin 91: VSS : - : Digital ground.
pin 92: VDD : - : Digital power supply.
pin 93: Memo D 8 :I/O:Pattern Memory interface. Data I/O.
pin 94: Memo D 0 :I/O:Pattern Memory interface. Data I/O.
pin 95: Memo RAHZ_N :IN: Pattern Memory interface. High-impedance.
pin 96: X TEST 2 :IN: For the test. Connect to VDD.
pin 97: X TEST 1 :IN: For the test. Connect to VDD.
pin 98: X TEST 0 :IN: For the test. Connect to VDD.
pin 99: Moni V S IN_N :IN: Monitor interface. Vertical Sync input.
pin100: Moni H S IN_N :IN: Monitor interface. Horizontal Sync input.
pin101: NC : - : Not in use.
pin102: A VDD : - : Analog power supply.
pin103: Moni Red : O : Monitor interface. Analog Red output.
pin104: Moni Green : O : Monitor interface. Analog Green output.
pin105: Moni Blue : O : Monitor interface. Analog Blue output.
pin106: Moni IREF : - : Monitor interface. DAC reference power
supply.
pin107: A VSS : - : Analog ground.
pin108: NC : - : Not in use.
pin109: VDD : - : Digital power supply.
pin110: VSS : - : Digital ground.
pin111:Moni D Red 0 : O : Monitor interface. Digital Red output.
pin112:Moni D Red 1 : O : Monitor interface. Digital Red output.
pin113:Moni D Red 2 : O : Monitor interface. Digital Red output.
pin114:Moni D Red 3 : O : Monitor interface. Digital Red output.
pin115:Moni D Red 4 : O : Monitor interface. Digital Red output.
pin116:Moni D Red 5 : O : Monitor interface. Digital Red output.
pin117: VSS : - : Digital ground.
pin118: VDD : - : Digital power supply.
pin119: Moni D Green 0: O : Monitor interface. Digital Green output.
pin120: Moni D Green 1: O : Monitor interface. Digital Green output.
pin121: Moni D Green 2: O : Monitor interface. Digital Green output.
pin122: Moni D Green 3: O : Monitor interface. Digital Green output.
pin123: Moni D Green 4: O : Monitor interface. Digital Green output.
pin124: Moni D Green 5: O : Monitor interface. Digital Green output.
pin125: VSS : - : Digital ground.
pin126: VDD : - : Digital power supply.
pin127: Moni D Blue 0 : O : Monitor interface. Digital Blue output.
pin128: Moni D Blue 1 : O : Monitor interface. Digital Blue output.
pin129: Moni D Blue 2 : O : Monitor interface. Digital Blue output.
pin130: Moni D Blue 3 : O : Monitor interface. Digital Blue output.
pin131: Moni D Blue 4 : O : Monitor interface. Digital Blue output.
pin132: Moni D Blue 5 : O : Monitor interface. Digital Blue output.
pin133: VSS : - : Digital ground.
pin134: Moni FSC : O : Monitor interface. Sub-carrier clock.
pin135: Moni YS_N : O : Monitor interface. YS output.
pin136: Moni V SYNC_N:O : Monitor interface. Vertical Sync output.
pin137: Moni H/C SYN_N : O:
Monitor interface. Horizontal/Composite
Sync output.
pin138: Moni BLANK_N : O : Monitor interface. Blank output.
pin139: Moni DOT CLK : O : Monitor interface. Dot clock output.
pin140: VDD : - : Digital power supply.
pin141: X IN :IN: Crystal connection.
pin142: X OUT : O : Crystal connection.
pin143: VSS : - : Digital ground.
pin144: NC : - : Not in use.
051-7221-18 TC7SH04FU Single Inverter
051-7509-90 SN74LV123APWR
Dual Retriggerable Monostable Multivibrator
Terminal Description
pin 1 : 1 A_ : Channel 1 input A_. Ref. Table 1.
pin 2 : 1 B : Channel 1 input B. Ref. Table 1.
pin 3 : 1 CLR_ : Channel 1 Clear in. Ref. Table 1.
pin 4 :1 Q_ : Channel 1 Negative output. Ref. Table 1.
pin 5 : 2 Q :Channel 2 Positive output. Ref. Table 1.
pin 6 : 2 CX : Connect to RX/CX through a capacitor.
pin 7 : 2 RX/CX : Connect to CX through a capacitor, and con-
nect to VCC through a resistor.
pin 8 : GND : Ground.
pin 9 : 2 A_ : Channel 2 input A_. Ref. Table 1.
pin 10:2 B : Channel 2 input B. Ref. Table 1.
pin 11: 2 CLR_ :Channel 2 Clear in. Ref. Table 1.
pin 12:2 Q_ : Channel 2 Negative output. Ref. Table 1.
pin 13:1 Q : Channel 1 Positive output. Ref. Table 1.
pin 14: 1 CX : Connect to RX/CX through a capacitor.
pin 15: 1 RX/CX : Connect to CX through a capacitor, and con-
nect to VCC through a resistor.
pin 16: VCC : Positive supply voltage.
Table 1.
A_ in B in CLR_ in Q out Q_ out
Output Enable D-E H H U-P D-P
Inhibit X L H L H
Inhibit H X H L H
Output enable L U-E H U-P D-P
Output enable L H U-E U-P D-P
Reset X X L L H
D-E : Down-edge
D-P : Down-pulse
U-E : Up-edge
U-P : Up-pulse
X : Don't care.
1
2
3
5
4
VCC
OUT
NC
IN
GND
1
2
3
4
5
6
7
8
1A_
1B
1Clear_
1Q_
VCC
1Rx/Cx
1Cx
1Q
16
15
14
13
12
11
10
9
CK
Clear
CK
Clear
2Q_
2Clear_
2B
2A_
2Q
2Cx
2Rx/Cx
GND
to VCC

VRX765VD
VRX766VD -12-
052-7078-01 uPD703276YGJ-512UENA System Controller
is for legal or rightholder-authorized copying only. Don't steal
music.
iPod is a trademark of Apple Computer, Inc., registered in the U.S.
and other countries.
TerminalDescription
pin 1: A Vref 0 : - : Reference voltage for the internal ADC.
pin 2: A VSS : - : Negative voltage supply for analog section.
pin 3: SYS ACC : O : ACC detect signal output.
pin 4: SUB MUTE : O : Sub-zone audio mute signal output.
pin 5: A Vref 1 : - : Reference voltage for the internal DAC.
pin 6: RDS CLK :IN: Not in use.
pin 7: AV ON : O : The ON command output to the power
supply section.
pin 8: FLASH :IN: The signal input for the flash memory con-
trol.
pin 9: VDD : - : Positive voltage supply.
pin 10: REG C : - : The capacitor connection.
pin 11: GND : - : Ground.
pin 12: X in :IN: Crystal connection. Main 31.4MHz.
pin 13: X out : O : Crystal connection. Main 31.4MHz.
pin 14: RESET :IN: Reset signal input.
pin 15: XT I :IN: Crystal connection. Sub 32.758kHz.
pin 16: XT O : O : Crystal connection. Sub 32.758kHz.
pin 17: POWER KEY :IN: Power key input.
pin 18: BU 9V DET :IN: Backup 9V detection.
pin 19: BU 6V DET :IN: Backup 6V detection.
pin 20: NU :IN: Not in use.
pin 21: OSD INT :IN: The interrupt signal input for the on
screen display.
pin 22: TUN SDA :I/O:I2BUS serial data input/output for the tun-
er pack.
pin 23: TUN SCL : O : I2BUS serial clock output for the tuner
pack.
pin 24: TP REQ :IN: The request signal from the touch panel
micro computer.
pin 25: iPod/FLASH O : O : Serial data output to iPod or flash memo-
ry.
pin 26: iPod/FLASH IN :IN: Serial data input from iPod or flash mem-
ory.
pin 27: TP RST : O : The reset pulse output to the touch panel
micro computer.
pin 28: DIMMER : O : PWM output.
pin 29: Motor PLS :IN: Motor Pulse input.
pin 30: NAVI ON : O : The image signal ON command output for
the navigation.
pin 31: IE BUS TX : O : IE Bus serial data output.
pin 32: IE BUS RX :IN: IE Bus serial data input.
pin 33: GND : - : Ground.
pin 34: E VDD : - : Positive voltage supply.
pin 35: DSP SDA :I/O:The serial data input/output for the digital
signal processor.
pin 36: DSP SCL : O : SCL output to the digital signal processor.
pin 37: Motor 1 F : O : L = Open.
pin 38: Motor 1 R : O : L = Close.
pin 39: Motor 2 F : O : L = Tilt Up.
pin 40: Motor 2 R : O : L = Tilt Down.
pin 41: OFFSET DET :IN: Offset-detection input.
pin 42: Amp Standby : O : The standby signal output to the amplifi-
er.
pin 43: NU :IN: Not in use.
pin 44: NU :IN: Not in use.
pin 45: NU :IN: Not in use.
pin 46: NU :IN: Not in use.
pin 47: NU :IN: Not in use.
pin 48: NU :IN: Not in use.
pin 49: NU :IN: Not in use.
pin 50: NU :IN: Not in use.
pin 51: NU :IN: Not in use.
pin 52: NU :IN: Not in use.
pin 53: IRI :IN: The remote control signal input.
pin 54: NU :IN: Not in use.
pin 55: NU :IN: Not in use.
pin 56: NU :IN: Not in use.
pin 57: NU :IN: Not in use.
pin 58: OSD RST : O : The reset pulse output for the on screen
display IC.
pin 59: TP RX :IN: The serial data input from the touch pan-
el micro computer.
pin 60: TP TX : O : The serial data output to the touch panel
micro computer.
pin 61: DVD TX : O : The serial data output to the DVD mech-
anism.
pin 62: DVD RX :IN: The serial data input from the DVD mech-
anism.
pin 63: W REMCOM :IN: Wired remote controller signal input.
pin 64: BLKO : O : The blanking signal output.
pin 65: VID / RGB : O : L = Video, H = RGB.
pin 66: FL ON : O : The fluorescent light of the LCD ON sig-
nal output.
pin 67: BEEP : O : Beep out.
pin 68: OSD RX :IN: Serial data input from on-screen-display
IC.
pin 69: OSD TX : O : Serial data output to on-screen-display IC.
pin 70: OSD SCK : O : The clock pulse output to the on screen
display IC.
pin 71: OSD CE : O : Chip enable output to on-screen-display
IC.
pin 72: OSD INH : O : Inhibit pulse output to on-screen-display
IC.
pin 73: Freq SEL : O : Frequency select.
pin 74: OPN/CL SW :IN: Open/Close switch signal input.
pin 75: EJECT SW :IN: Eject switch signal input.
pin 76: CATS DET :IN: CATS or DCP detection input.
pin 77: ROM EN : O : ROM enable signal output. L = OSD OFF.
pin 78: NU : O : Not in use.
pin 79: NU :IN: Not in use.
pin 80: iPod PWR ON : O : iPod power ON signal output.
pin 81: Panel ON : O : LCD panel ON signal output.
pin 82: FAN ON : O : The fan on signal output.
pin 83: TV/OTHER : O : Horizontal sync select. H = TV.
pin 84: FLASH READY :IN: Ready signal input from flash memory.
pin 85: EEP DO : O : The serial data output to the EEP-ROM.
pin 86: CLK OUT : O : SUB-CLOCK-PLUSE output.
pin 87: EEP CK : O : The clock pulse output to the EEP-ROM.
pin 88: EEP CE : O : The chip enable signal output to the EEP-
ROM.
pin 89: EEP DI :IN: The serial data input from the EEP-ROM.
pin 90: NU :IN: Not in use.
pin 91: KI 0 :IN: Key scan signal input.
pin 92: KI 1 :IN: Key scan signal input.
pin 93: KI 2 :IN: Key scan signal input.
pin 94: KI 3 :IN: Key scan signal input.
pin 95: KO 0 : O : Key scan signal output.
pin 96: KO 1 : O : Key scan signal output.
pin 97: KO 2 : O : Key scan signal output.
pin 98: KO 3 : O : Key scan signal output.
pin 99: USA/3rd :IN: L = Asia, H = North America.
pin100: Mechanism :IN: L = Without the mechanism.
pin101: NTSC/PAL :IN: NTSC/PAL select signal input. L = NTSC.
pin102: FLASH WR :IN: The write flag input for the flash memory.
pin103: B VSS : - : Ground for the bus interface section.
pin104: B VDD : - : Positive voltage supply for the bus inter-
face section.
pin105: ILL DET :IN: Illumination ON signal input.
pin106: BUS ILL : O : Illumination-ON signal output for Ce-NET.
pin107: ILL ON : O : The illumination ON signal output.
pin108: Blink LED : O : LED Blinking signal output.
pin109: DVD ON 2 : O : DVD ON signal output.
pin110: NU :IN: Not in use.
pin111: DVD RST : O : The reset signal output to the DVD mech-
anism.

VRX765VD
VRX766VD
-13-
pin112: DSP RST : O : Reset pulse output to the DSP IC.
pin113: DSP INIT :IN: The initial finished signal input from the
Radio-Audio-DSP.
pin114: SAMPLE :IN: Not in use.
pin115: NU : - : Not in use.
pin116: AM/FM 8V ON : O : AM/FM 8V ON signal output.
pin117: RDS DATA :IN: RDS serial data input.
pin118: AM/FM 5V ON : O : AM/FM 5V ON signal output.
pin119: iPod DET :IN: H = iPod is connected.
pin120: NU : - : Not in use.
pin121: DAC RESET : O : The reset pulse output to DAC.
pin122: SYS MUTE : O : System muting signal output.
pin123: AMP MUTE : O : Muting signal output to the Audio Power
Amplifier.
pin124: NU : - : Not in use.
pin125: Motor PWR : O : L = High Speed.
pin126: Photo Sens :IN: Photo sensor signal input.
pin127: Rear Im Sel 4 : O : Rear image signal selection. Refer Table
2.
pin128: Rear Im Sel 3 : O : Rear image signal selection. Refer Table
2.
pin129: TILT VR :IN: Input-terminal of internal ADC to read the
value of tilt-volume.
pin130: FAN TEMP :IN: The input terminal of the internal ADC to
detect the temperature.
pin131: Rear Im Sel 2 : O : Rear image signal selection. Refer Table
2.
pin132: Rear Im Sel 1 : O : Rear image signal selection. Refer Table
2.
pin133: Frnt Im Sel 3 : O : Front image signal selection. Refer Table
1.
pin134: Frnt Im Sel 2 : O : Front image signal selection. Refer Table
1.
pin135: Frnt Im Sel 1 : O : Front image signal selection. Refer Table
1.
pin136: SEL 3 :IN: The selection signal input.
pin137: SEL 2 :IN: The selection signal input.
pin138: PKB :IN: The parking brake signal input.
pin139: PHONE INT :IN: The telephone interrupt signal input.
pin140: NU : - : Not in use.
pin141: AMP REM DT :IN: Remote controller wire short detection.
pin142: AMP REM O : O : ON signal output to the amplifier.
pin143: AUTO ANT : O : Auto antenna control signal output.
pin144: ACC IN :IN: ACC ON flag input.
Table 1. Front image signal selection
Visual TV DVD CCD
Frnt Im Sel 1 ( pin 135 ) L H L L
Frnt Im Sel 2 ( pin 134 ) L L H L
Frnt Im Sel 3 ( pin 133 ) H H H L
Table 2. Rear image signal selection
Visual TV DVD DVD A/C
Rear Im Sel 1 ( pin 132 ) L H L L
Rear Im Sel 2 ( pin 131 ) L L H L
Rear Im Sel 3 ( pin 128 ) H H H L
Rear Im Sel 4 ( pin 127 ) L L L H
052-7079-00 TC58FVM5B3AFTG65 Lower CMOS Flash Memory
Terminal Description
pin 1: A 15 :IN: Address signal input.
pin 2: A 14 :IN: Address signal input.
pin 3: A 13 :IN: Address signal input.
pin 4: A 12 :IN: Address signal input.
pin 5: A 11 :IN: Address signal input.
pin 6: A 10 :IN: Address signal input.
pin 7: A 9 :IN: Address signal input.
pin 8: A 8 :IN: Address signal input.
pin 9: A 19 :IN: Address signal input.
pin 10: A 20 :IN: Address signal input.
pin 11: WE :IN: Write enable signal input.
pin 12: RESET :IN: Reset signal input.
pin 13: NU : - : Not in use.
pin 14: WP/ACC :IN: The write protection signal input / The
acceleration signal input.
pin 15: RY/BY : O : The ready/busy signal output.
pin 16: A 18 :IN: Address signal input.
pin 17: A 17 :IN: Address signal input.
pin 18: A 7 :IN: Address signal input.
pin 19: A 6 :IN: Address signal input.
pin 20: A 5 :IN: Address signal input.
pin 21: A 4 :IN: Address signal input.
pin 22: A 3 :IN: Address signal input.
pin 23: A 2 :IN: Address signal input.
pin 24: A 1 :IN: Address signal input.
pin 25: A 0 :IN: Address signal input.
pin 26: CE :IN: Chip enable signal input.
pin 27: VSS : - : Negative supply voltage.
pin 28: OE :IN: Output enable signal input.
pin 29: D 0 :I/O:Data input/output.
pin 30: D 8 :I/O:Data input/output.
pin 31: D 1 :I/O:Data input/output.
pin 32: D 9 :I/O:Data input/output.
pin 33: D 2 :I/O:Data input/output.
pin 34: D 10 :I/O:Data input/output.
pin 35: D 3 :I/O:Data input/output.
pin 36: D 11 :I/O:Data input/output.
pin 37: VDD : - : Positive supply voltage.
pin 38: D 4 :I/O:Data input/output.
pin 39: D 12 :I/O:Data input/output.
pin 40: D 5 :I/O:Data input/output.
pin 41: D 13 :I/O:Data input/output.
pin 42: D 6 :I/O:Data input/output.
pin 43: D 14 :I/O:Data input/output.
pin 44: D 7 :I/O:Data input/output.
pin 45: D 15/A-1 :I/O:Data input/output. A-1 address input.
pin 46: VSS : - : Negative supply voltage.
pin 47: BYTE/WORD :IN: Byte / Word selection.
pin 48: A 16 :IN: Address signal input.

VRX765VD
VRX766VD -14-
EXPLODED VIEW : PARTS LIST
Main section
68
85
82
64
74
71
70
69
87
78
75
79
80
81
89
76
67
88
17
18
16
21
36
796
3
9
15
13
54
44
14
46
44
11
1
2
4
10
104
40
21
23
48
41
41
38
47
99
43
56
56
56
41
38
38
29
24
51 51
6
86
8
40
28
33
30 26
31
43
73
72
61
61 91
49
49
20
50
32
92
93
45
27
41
53
52
39
39
22
25
59
5
57
65
56
38
19
95
66
77
83
90
94
63
62
35
37
34
42
55
58
60
38
84
38
98
97
97
100
103
101
102
12
104

VRX765VD
VRX766VD
-15-
1 DCP-558-600 DCP-ASSY(B-A) 1
DCP-559-800 DCP-ASSY(K-A,K-B,K-C)
2 ----------- INNER-ES-SECTION 1
3 335-7790-00 TOP-CVR 1
4 370-6925-00 PANEL-ES 1
5 378-0553-00 BADGE(CLARION) 1
6 948-0692-05 SLIDE-MECH-ASSY 1
7 013-9710-00 TOUCH PANEL 1
8 020-3042-01 DC-MOTOR 1
9 039-2793-00 FPC(MAIN-LCD) 1
10 039-2509-00 FPC(45P) 1
11 286-6827-01 SETPLATE(B-A) 1
276-0026-01 SETPLATE(K-A)
276-0027-01 SETPLATE(K-B)
276-0028-01 SETPLATE(K-C)
12 311-1921-00 LOWER CASE 1
13 331-4174-00 MECH-CVR 1
14 331-4175-00 MECH-BRKT 1
15 331-4176-00 HEAT SINK CVR 1
16 331-3884-01 LCD BRKT 1
17 335-7163-10 SIDE-CVR(L) 1
18 335-7164-10 SIDE-CVR(R) 1
19 345-3799-20 RCA CAP 1
20 345-5470-00 RUBBER PART 1
21 347-6085-00 DOUBLE FACE 2
22 331-4177-00 FPC-CVR(SIDE) 1
23 347-7038-00 SPACER 2
24 347-7260-00 INSULATOR 1
25 331-4173-00 FPC COVER 1
26 347-7262-01 INSULATOR 1
27 347-7739-00 DOUBLE FACE 1
28 347-8029-00 INSULATOR 1
29 347-8028-00 SHADE 1
30 347-7282-00 FILM 1
31 347-7300-00 INSULATOR 1
32 347-7301-00 FILM 2
33 347-7302-00 DOUBLE FACE 1
34 347-8030-00 PROTECT SHEET 1
35 347-8031-00 PROTECT SHEET 1
36 379-0468-00 TFT 1
37 347-8032-00 PROTECT SHEET 1
38 714-2605-8B MACHINE SCREW(M2.6 x5) 11
39 714-5008-4B MACHINE SCREW(M5 x8) 2
40 716-0872-61 PAD SCREW(M1.7 x6 BLK) 7
41 716-0878-50 IT SCREW(M2.6 x5) 4
42 331-4231-00 EARTH PLATE 2
43 716-1816-50 IT SCREW(M2 x4) 2
44 731-2608-8A TAPTIGHT 4
45 331-3946-00 COVER PLATE 1
46 039-2792-00 FPC(DVD-MECH) 1
47 816-2650-00 FLAT WIRE(14P L39) 1
48 780-2612-50 SCREW(M2.6 x12) 2
49 781-1722-50 PLATE SCREW(M1.7x2.2) 4
50 781-1750-50 SCREW(phi1.7x2.2) 4
51 781-2002-50 PLATE SCREW(M2.0X2) 4
52 750-3137-03 SPRING(R) 1
53 750-3137-02 SPRING(L) 1
54 929-2504-00 DIGITAL-MECH 1
55 347-5867-00 DOUBLE FACE 1
56 714-2604-8B MACHINE SCREW(M2.6 x4) 13
57 716-1468-01 SCREW (M2 x2.5) 2
58 347-8033-00 INSULATOR 1
59 855-5436-50 RCA PIN CORD 1
60 353-0585-00 SHADE 2
61 ----------- SUB PWB 1
62 074-2001-64 OUTLET SOCKET 1
63 074-2001-62 OUTLET SOCKET 1
64 880-2091D TUNER 1
65 347-7283-00 FILM 1
66 074-1289-80 OUTLET SOCKET(30PDVD) 1
67 074-0881-17 OUTLET SOCKET 1
68 060-0100-50 BUZZER 1
69 074-1194-00 OUTLET SOCKET 1
70 074-1214-00 OUTLET SOCKET 1
71 075-0385-00 JACK 1
72 076-0349-02 PLUG 2
73 076-0353-17 PLUG 1
74 076-0714-20 PLUG 1
75 313-1970-00 HEAT SINK(TR) 1
76 313-1905-00 HEAT SINK(POWER IC) 1
77 074-1205-93 OUTLET SOCKET 1
78 331-4178-00 IC-HOLDER 1
79 331-3850-00 CONECTOR HOLDER 1
80 331-4179-00 IC HOLDER(POWER IC) 1
81 331-4180-00 CONNECTOR HOLD 1
82 331-4182-00 SHIELD CVR 1
83 074-2001-64 OUTLET SOCKET 1
84 331-4311-00 BACK-CVR 1
85 347-7285-00 SPACER(FPC) 1
86 ----------- MAIN PWB 1
87 714-2606-8B MACHINE SCREW(M2.6 x6) 4
88 731-2612-8B TAPTIGHT 2
89 816-3013-50 FLAT WIRE(14P L65) 1
90 074-2011-70 OUTLET SOCKET(20P) 1
91 714-3005-8B MACHINE SCREW(M3 x5) 1
92 074-1171-10 OUTLET SOCKET 1
93 331-4181-00 SHIELD CVR(R) 1
94 074-4020-00 OUTLET SOCKET(ANT) 1
95 092-2226-00 ANT-RECEPT 1
96 331-4199-00 SHIELD CVR 1
97 074-2001-95 OUTLET SOCKET(45) 2
98 074-1138-54 OUTLET SOCKET(4P) 1
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY
Note)Some parts depend on each model.The model name is specified in the descripion .
(B-A;QC-6823B-A, K-A;PF-QC-6823K-A, K-B;QC-6823K-B , K-C;QC-6823K-C)

VRX765VD
VRX766VD -16-
1 ----------- SW PWB 1
2 370-6924-00 ESCUTCHEON(INNER) 1
3 382-7862-00 INNER-BUTTON(L) 1
4 382-7863-00 INNER-BUTTON(M) 1
5 382-7864-00 INNER-BUTTON(R) 1
6 335-7788-00 DISC GUIDE 1
7 346-0200-00 LEATHER SHEET 1
8 331-4168-00 DISCGUIDE PLATE 1
9 331-4169-00 ES-PLATE 1
10 382-7865-00 RESET BUTTON 1
11 074-1289-70 OUTLET SOCKET(20P) 1
12 335-7791-00 LED HOLDER(L) 1
13 335-7789-00 LED HOLDER(R) 1
14 347-7854-00 SLIDER 2
15 816-3012-50 FLAT WIRE(20P) 1
99 074-2001-80 OUTLET SOCKET 1
100 076-0568-00 PLUG(2P) 1
101 074-1189-85 OUTLET SOCKET(35P) 1
102 074-2001-64 OUTLET SOCKET(14P) 1
103 074-2001-70 OUTLET SOCKET(20P) 1
104 ----------- LCD PWB
Inner Escutcheon section
16 716-0872-51 PAD SCREW(M1.7 x5) 13
17 716-0872-21 PAD SCREW(M1.7 x4) 3
18 624-0016-00 MAGNET 1
19 335-7787-00 IR PLATE 1
20 946-0088-00 MAGNET PLATE ASSY 1
21 331-4170-00 LED COVER(L) 1
22 331-4171-00 LED COVER(R) 1
23 076-0708-02 PLUG(2P) 1
24 076-2010-03 PLUG(3P) 1
25 013-7411-51 SWITCH 1
26 001-7097-90 DIODE(CL-194S-W) 7
27 013-6312-50 SWITCH 15
28 060-4017-90 IR-RECIEVER 1
29 013-6513-50 LUMI-SWITCH 1
6
8
13
12
14
2
3
4
5
7
9
10 14
1
1
1
23
21
24
22
16
16
16
27
27
27
28 29
11
17
17
18
19
26
26
17
20
15
25
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY

VRX765VD
VRX766VD
-17-
DCP section
1 370-6923-00 ESCUTCHEON(F) 1
2 373-1102-00 DIAL-CVR(B-A) 1
373-1102-01 DIAL-CVR(K-A,K-B,K-C)
3 335-7781-00 REAR-CVR 1
4 382-7852-00 BUTTON(IPOD) 1
5 382-7853-00 BUTTON(TOP) 1
6 382-7854-00 BUTTON(CONT) 1
7 382-7855-00 BUTTON(SRC) 1
8 382-7856-00 BUTTON(BND/ADJ/M) 1
9 382-7857-00 BUTTON(ISR/OP/EJ) 1
10 382-7858-00 BUTTON(MUTE/DOWN) 1
11 382-7859-00 BUTTON(T-UP) 1
12 382-7860-00 BUTTON(VOL) 2
13 347-8023-00 REFLECTOR(L) 1
14 347-8024-00 REFLECTOR(R) 1
15 335-7782-00 BUTTON HOLDER(VOL) 2
16 335-7783-00 RING PLATE 1
17 335-7784-00 RING COVER 1
18 335-7785-00 ILLUMI PLATE(L) 1
19 335-7786-00 ILLUMI PLATE(R) 1
20 750-6816-00 SPRING 2
21 347-8022-00 DOUBLE FACE(VOL) 2
22 716-0872-61 PAD SCREW(M1.7x6 BLK) 11
23 354-7593-00 MAGNET 1
24 335-7787-00 IR PLATE 1
1
12
2
8
9
6
5
4
17
16
7
15
20
21
10
13
18
3
23
22
19
14
11
22
22
24
22
12
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY

VRX765VD
VRX766VD -18-
Note)Some parts depend on each model.The model name is specified in the descripion .
(B-A;QC-6823B-A, K-A;PF-QC-6823K-A, K-B;QC-6823K-B , K-C;QC-6823K-C)
ANT101 092-2226-00 ANT-RECEPT
BL101 880-2091D AM/FM TUNER
C101 166-2201-50 22pF CH
C102 166-1511-50 150pF CH
C104 168-1032-55 0.01uF K
C105 042-0643-51 16V 100uF
C106 168-2232-55 0.022uF K
C107 166-1011-50 100pF CH
C108 168-1022-55 1000pF K
C109 168-1042-78 16V 0.1uF
C110 168-1042-78 16V 0.1uF
C111 042-0560-84 16V 470uF
C112 043-0540-00 6.3V 10uF
C113 043-0540-00 6.3V 10uF
C114 043-0540-00 6.3V 10uF
C115 043-0540-00 6.3V 10uF
C116 168-1042-78 16V 0.1uF
C117 043-0540-00 6.3V 10uF
C118 043-0540-00 6.3V 10uF
C119 043-0540-00 6.3V 10uF
C120 166-1011-50 100pF CH
C121 166-1011-50 100pF CH
C122 178-1052-78 1uF
C123 042-0592-58 16V 10uF
C126 168-1042-78 16V 0.1uF
C127 042-0592-58 16V 10uF
C128 168-1042-78 16V 0.1uF
C129 042-0595-84 10V 100uF
C130 168-1045-56 0.1uF Z
C131 163-4753-55 35V 4.7uF
C132 168-4712-55 470pF K
C133 168-4712-55 470pF K
C134 168-4712-55 470pF K
C135 168-4712-55 470pF K
C136 168-1042-78 16V 0.1uF
C137 168-1045-56 0.1uF Z
C138 163-1073-15 6.3V 100uF
C139 163-2263-35 16V 22uF
C140 168-4735-56 0.047uF Z
C141 043-0540-00 6.3V 10uF
C142 043-0540-00 6.3V 10uF
C143 166-4701-50 47pF CH
C144 166-4701-50 47pF CH
C145 168-1042-78 16V 0.1uF
C146 166-1011-50 100pF CH
C147 043-0540-00 6.3V 10uF
C148 043-0540-00 6.3V 10uF
C149 043-0540-00 6.3V 10uF
C150 166-1011-50 100pF CH
C153 166-1011-50 100pF CH
C154 178-1052-78 1uF
C155 168-1045-56 0.1uF Z
C156 166-1011-50 100pF CH
C157 168-1042-78 16V 0.1uF
C158 042-0560-84 16V 470uF
C159 168-1045-56 0.1uF Z
C160 042-0619-51 6.3V 56uF
C161 168-1045-56 0.1uF Z
C162 042-0423-20 10V 10uF
C163 168-3335-56 0.033uF Z
C164 168-3322-55 3300pF K
C165 168-3322-55 3300pF K
C166 168-1045-56 0.1uF Z
C167 163-1073-15 6.3V 100uF
C168 168-3322-55 3300pF K
C169 168-3322-55 3300pF K
C170 168-2232-55 0.022uF K
C171 168-4712-55 470pF K
ELECTRICAL PARTS LIST
Main PWB(B1) section
C173 166-1011-50 100pF CH
C174 168-2232-55 0.022uF K
C175 168-2232-55 0.022uF K
C178 168-2232-55 0.022uF K
C181 166-1007-50 10pF CH
C182 166-1007-50 10pF CH
C184 168-1022-55 1000pF K
C185 168-1022-55 1000pF K
C186 168-1042-78 16V 0.1uF
C187 166-1011-50 100pF CH
C188 163-4753-55 35V 4.7uF
C189 168-1042-78 16V 0.1uF
C190 168-1022-55 1000pF K
C191 168-1022-55 1000pF K
C192 163-4753-55 35V 4.7uF
C193 168-1042-78 16V 0.1uF
C194 166-1811-50 180pF CH
C195 168-1045-56 0.1uF Z
C196 163-4753-55 35V 4.7uF
C197 042-0619-51 6.3V 56uF
C198 168-1042-78 16V 0.1uF
C199 168-1042-78 16V 0.1uF
C201 168-1022-55 1000pF K
C202 043-0540-00 6.3V 10uF
C203 168-1022-55 1000pF K
C204 168-1022-55 1000pF K
C205 043-0540-00 6.3V 10uF
C206 043-0540-00 6.3V 10uF
C207 168-1022-55 1000pF K
C208 168-1022-55 1000pF K
C209 043-0540-00 6.3V 10uF
C210 163-2273-25 10V 220uF
C211 043-0540-00 6.3V 10uF
C212 168-1022-55 1000pF K
C213 168-4712-55 470pF K
C214 168-4712-55 470pF K
C215 043-0540-00 6.3V 10uF
C217 168-4712-55 470pF K
C218 168-4712-55 470pF K
C219 043-0540-00 6.3V 10uF
C221 168-4712-55 470pF K
C222 168-4712-55 470pF K
C223 043-0540-00 6.3V 10uF
C225 168-4712-55 470pF K
C226 168-4712-55 470pF K
C227 043-0540-00 6.3V 10uF
C229 168-6812-55 680pF K
C230 168-6812-55 680pF K
C231 043-0540-00 6.3V 10uF
C233 168-6812-55 680pF K
C234 168-6812-55 680pF K
C235 043-0540-00 6.3V 10uF
C237 168-6812-55 680pF K
C238 168-6812-55 680pF K
C239 043-0540-00 6.3V 10uF
C241 168-6812-55 680pF K
C242 168-6812-55 680pF K
C243 042-0592-58 16V 10uF
C244 168-1042-78 16V 0.1uF
C245 042-0592-58 16V 10uF
C246 168-1042-78 16V 0.1uF
C247 043-0541-00 6.3V 22uF
C249 043-0264-56 270pF
C250 166-2701-50 27pF CH
C251 043-0541-00 6.3V 22uF
C253 043-0264-56 270pF
C254 166-2701-50 27pF CH
C256 043-0541-00 6.3V 22uF
C258 043-0264-56 270pF
C259 166-2701-50 27pF CH
C260 043-0541-00 6.3V 22uF
C262 043-0264-56 270pF
C263 166-2701-50 27pF CH
C265 043-0541-00 6.3V 22uF
C266 043-0264-56 270pF
C267 166-2701-50 27pF CH
C268 043-0541-00 6.3V 22uF
C269 043-0264-56 270pF
C270 166-2701-50 27pF CH
C271 168-1032-55 0.01uF K
C272 043-0541-00 6.3V 22uF
C273 043-0264-56 270pF
C274 166-2701-50 27pF CH
C275 043-0541-00 6.3V 22uF
C276 043-0264-56 270pF
C277 166-2701-50 27pF CH
C280 168-1032-55 0.01uF K
C281 042-0592-58 16V 10uF
C282 042-0592-58 16V 10uF
C283 042-0592-58 16V 10uF
C284 042-0592-58 16V 10uF
C285 178-2242-78 0.22uF
C286 178-2242-78 0.22uF
C287 178-2242-78 0.22uF
C288 178-2242-78 0.22uF
C301 168-1042-78 16V 0.1uF
C302 168-1042-78 16V 0.1uF
C304 042-0592-58 16V 10uF
C306 168-1042-78 16V 0.1uF
C307 042-0423-97 16V 10uF
C308 168-1042-78 16V 0.1uF
C310 042-0423-20 10V 10uF
C311 168-1042-78 16V 0.1uF
C312 042-0423-20 10V 10uF
C313 168-1042-78 16V 0.1uF
C314 042-0423-20 10V 10uF
C316 168-1042-78 16V 0.1uF
C317 168-1045-56 0.1uF Z
C318 042-0630-50 16V 100uF
C319 042-0630-50 16V 100uF
C320 168-1042-78 16V 0.1uF
C322 042-0643-51 16V 100uF LOW-
ESR
C324 042-0643-51 16V 100uF LOW-
ESR
C325 042-0643-51 16V 100uF LOW-
ESR
C326 168-1045-56 0.1uF Z
C327 178-1052-78 1uF
C328 178-1052-78 1uF
C329 178-1052-78 1uF
C330 178-1052-78 1uF
C331 178-1052-78 1uF
C332 178-1052-78 1uF
C333 168-1032-55 0.01uF K
C334 178-1052-78 1uF
C335 168-1032-55 0.01uF K
C336 163-4763-35 16V 47uF
C337 163-4763-15 6.3V 47uF
C338 166-3096-50 3pF CJ
C339 163-4763-15 6.3V 47uF
C340 163-4763-15 6.3V 47uF
C341 168-1042-78 16V 0.1uF
C342 163-1073-35 16V 100uF
C343 042-0643-52 6.3V 1000uF
C344 168-4712-55 470pF K
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
Note) Severaldifferentpartsofthesamereferencenumberarealternativeparts.
Oneofthosepartsisusedintheset.

VRX765VD
VRX766VD
-19-
C345 168-4712-55 470pF K
C401 168-1042-78 16V 0.1uF
C402 043-0540-00 6.3V 10uF
C403 043-0540-00 6.3V 10uF
C404 168-1042-78 16V 0.1uF
C405 168-1042-78 16V 0.1uF
C406 168-1042-78 16V 0.1uF
C407 168-4722-55 4700pF K
C408 166-2211-50 220pF CH
C409 168-1042-78 16V 0.1uF
C410 043-0540-00 6.3V 10uF
C411 168-1042-78 16V 0.1uF
C412 166-1007-50 10pF CH
C413 166-1007-50 10pF CH
C414 166-1011-50 100pF CH
C415 168-1042-78 16V 0.1uF
C416 168-1042-78 16V 0.1uF
C417 168-1042-78 16V 0.1uF
C418 168-1042-78 16V 0.1uF
C421 168-1042-78 16V 0.1uF
C422 168-1042-78 16V 0.1uF
C423 043-0540-00 6.3V 10uF
C424 168-1042-78 16V 0.1uF
C425 168-1042-78 16V 0.1uF
C426 168-1042-78 16V 0.1uF
C427 168-1042-78 16V 0.1uF
C428 043-0540-00 6.3V 10uF
C429 168-1042-78 16V 0.1uF
C430 043-0540-00 6.3V 10uF
C431 168-1042-78 16V 0.1uF
C432 168-1042-78 16V 0.1uF
C433 166-1011-50 100pF CH
C434 168-1042-78 16V 0.1uF
C435 166-1011-50 100pF CH
C436 043-0540-00 6.3V 10uF
C437 176-2221-50 2200pF CH
C438 168-2222-55 2200pF K
C439 168-1042-78 16V 0.1uF
C441 168-1042-78 16V 0.1uF
C450 168-1042-78 16V 0.1uF
C451 168-1042-78 16V 0.1uF
C452 166-5601-50 56pF CH
C454 168-1042-78 16V 0.1uF
C455 168-1042-78 16V 0.1uF
C456 168-1042-78 16V 0.1uF
C457 043-0540-00 6.3V 10uF
C458 168-1042-78 16V 0.1uF
C459 168-1042-78 16V 0.1uF
C460 168-1042-78 16V 0.1uF
C461 168-1042-78 16V 0.1uF
C462 168-1042-78 16V 0.1uF
C463 043-0532-50 10V 10uF
C464 043-0532-50 10V 10uF
C465 168-1042-78 16V 0.1uF
C466 166-1201-50 12pF CH
C467 168-1042-78 16V 0.1uF
C468 178-1052-78 1uF
C469 178-1052-78 1uF
C470 178-1052-78 1uF
C471 178-1052-78 1uF
C472 178-1052-78 1uF
C473 178-1052-78 1uF
C474 178-1052-78 1uF
C475 178-1052-78 1uF
C476 178-1052-78 1uF
C477 168-1042-78 16V 0.1uF
C478 168-1042-78 16V 0.1uF
C479 168-1042-78 16V 0.1uF
C480 168-1042-78 16V 0.1uF
C484 168-1042-78 16V 0.1uF
C485 168-1042-78 16V 0.1uF
C486 168-1042-78 16V 0.1uF
C487 166-5601-50 56pF CH
C488 178-1052-78 1uF
C490 168-1022-55 1000pF K
C501 043-0540-00 6.3V 10uF
C502 168-1042-78 16V 0.1uF
C503 043-0540-00 6.3V 10uF
C504 168-1042-78 16V 0.1uF
C505 043-0551-90 6.3V 4.7uF M
C506 166-1801-50 18pF CH
C507 166-2201-50 22pF CH
C508 166-1011-50 100pF CH
C509 168-1042-78 16V 0.1uF
C510 168-1042-78 16V 0.1uF
C511 178-1052-78 1uF
C512 166-1011-50 100pF CH
C513 168-1032-55 0.01uF K
C514 168-1032-55 0.01uF K
C515 168-1022-55 1000pF K
C516 178-1052-78 1uF
C517 168-1042-78 16V 0.1uF
C518 168-1022-55 1000pF K
C519 178-1052-78 1uF
C521 042-1596-00 5.5V0.33F
C523 163-4763-15 6.3V 47uF
C605 178-4742-78 0.47uF
C606 042-0592-58 16V 10uF
C607 163-1053-65 50V 1uF
C608 178-1052-78 1uF
C609 042-1545-00 16V2200uF
C610 172-2241-11 0.22uF
C611 168-1022-55 1000pF K
C612 168-1022-55 1000pF K
C613 168-1022-55 1000pF K
C614 168-1022-55 1000pF K
C615 168-1022-55 1000pF K
C616 168-1022-55 1000pF K
C617 168-1022-55 1000pF K
C618 168-1022-55 1000pF K
C619 168-1042-78 16V 0.1uF
C620 042-1545-00 16V2200uF
C621 042-0627-90 16V 100uF
C622 042-0635-51 16V 39uF
C623 168-1042-78 16V 0.1uF
C624 168-1042-78 16V 0.1uF
C625 042-0627-90 16V 100uF
C626 168-1032-55 0.01uF K
C627 168-1032-55 0.01uF K
C628 042-0643-51 16V 100uF
C629 042-0643-56 16V 470uF M
C630 042-0643-56 16V 470uF M
C631 163-4763-35 16V 47uF
C632 042-0416-57 10V 47uF M TAN
C633 168-1042-78 16V 0.1uF
C634 178-3342-78 0.33uF
C635 043-0561-90 0.1uF
C636 163-3363-45 25V 33uF
C637 042-0595-84 10V 100uF
C638 163-2263-35 16V 22uF
C639 168-4732-78 0.047uF K
C640 166-1011-50 100pF CH
C641 166-1011-50 100pF CH
C642 166-1011-50 100pF CH
C643 168-1045-56 0.1uF Z
C644 043-0561-92 0.47uF
C645 178-1052-78 1uF
C646 172-2241-11 0.22uF
CCT403 050-0140-75 1/32W 330 ohm X4j
CCT408 050-0140-75 1/32W 330 ohm X4j
CCT411 050-0140-75 1/32W 330 ohm X4j
CCT412 050-0140-75 1/32W 330 ohm X4j
CCT413 050-0140-75 1/32W 330 ohm X4j
CCT414 050-0140-75 1/32W 330 ohm X4j
CCT415 050-0140-63 1/32W 47k ohm x4J
CCT416 050-0140-63 1/32W 47k ohm x4J
CCT417 050-0140-75 1/32W 330 ohm X4j
CCT418 050-0140-75 1/32W 330 ohm X4j
CCT419 050-0140-75 1/32W 330 ohm X4j
CCT420 050-0140-75 1/32W 330 ohm X4j
CCT421 050-0140-63 1/32W 47k ohm x4J
CCT422 050-0140-63 1/32W 47k ohm x4J
CCT505 050-0140-52 1/32W 100 ohm x4J
CCT506 050-0140-52 1/32W 100 ohm x4J
CCT507 050-0140-52 1/32W 100 ohm x4J
CCT508 050-0140-52 1/32W 100 ohm x4J
D101 001-0517-90 1SS355
D102 001-0517-90 1SS355
D103 001-0517-90 1SS355
D104 001-0529-21 MA8039-H
D201 001-0529-29 MA8051-M
D202 001-0517-90 1SS355
D203 001-0517-90 1SS355
D204 001-0529-44 MA8082-M
D301 001-0517-90 1SS355
D302 001-0517-90 1SS355
D303 001-0517-90 1SS355
D304 001-1305-90 DAN217U-T106
D305 001-1305-90 DAN217U-T106
D306 001-1305-90 DAN217U-T106
D501 001-0529-43 MA8082-L
D601 001-0592-00 RM4Z
D602 001-0517-90 1SS355
D603 001-0517-90 1SS355
D604 001-0517-90 1SS355
D605 001-0517-90 1SS355
D606 001-0517-90 1SS355
D607 001-2403-90 M1F60
D608 001-2403-90 M1F60
D609 001-2403-90 M1F60
D610 001-2403-90 M1F60
D611 001-0517-90 1SS355
D612 001-2403-90 M1F60
D613 001-0517-90 1SS355
D614 001-0517-90 1SS355
D615 001-0517-90 1SS355
D616 001-0517-90 1SS355
D617 001-0529-26 MA8047-M
D618 001-0504-47 HZS9B3L
D619 001-0529-43 MA8082-L
D620 001-2403-90 M1F60
D621 001-0517-90 1SS355
F602 060-8023-58 3A
IC101 051-0350-93 NJM4558M
IC102 051-0350-93 NJM4558M
IC103 051-1905-91 AN77L05M
IC104 051-6706-10 SAF7730H/N116F
IC105 051-3246-90 BA033FP
IC201 051-6703-08 AK4384VT
IC202 051-6703-08 AK4384VT
IC203 051-3026-90 NJM4580V
IC204 051-3026-90 NJM4580V
IC205 051-3026-90 NJM4580V
IC206 051-3026-90 NJM4580V
IC301 051-7243-48 SN74AHCT1G08DCKR
IC302 051-3317-90 LM1086IS-ADJ
IC303 051-3317-90 LM1086IS-ADJ
IC304 051-3289-00 BA09ST
IC305 051-5306-90 MM1117XF
IC306 051-5306-90 MM1117XF
IC307 051-5336-90 MM1227XFBE
IC308 051-5326-90 TK15420MTL
IC401 051-6456-00 YGV629-VZ
IC402 051-7509-90 SN74LV123APWR
IC403 051-7269-08 SN74AHC2G53HDCTR
IC405 052-7079-00 TC58FVM5B3AFTG65
IC451 051-7221-18 TC7SH04FU
IC452 051-7221-18 TC7SH04FU
IC454 051-5336-90 MM1227XFBE
IC455 051-7275-08 TC7W32FU TE12L
IC456 051-7221-18 TC7SH04FU
IC457 051-5342-90 NJM2524V
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION

VRX765VD
VRX766VD -20-
R117 119-4731-15 1/10W 47k ohm
R118 119-1831-15 1/10W 18k ohm
R119 119-4731-15 1/10W 47k ohm
R120 119-1831-15 1/10W 18k ohm
R121 119-4731-15 1/10W 47k ohm
R122 119-1831-15 1/10W 18k ohm
R125 119-1031-15 1/10W 10k ohm
R127 119-0000-05 1/10W 0 ohm JW
R128 119-1021-15 1/10W 1k ohm
R129 119-1221-15 1/10W 1.2k ohm
R130 119-1041-15 1/10W 100k ohm
R131 119-1241-15 1/10W 120k ohm
R132 119-1031-15 1/10W 10k ohm
R133 119-2231-15 1/10W 22k ohm
R134 119-1031-15 1/10W 10k ohm
R135 119-2231-15 1/10W 22k ohm
R136 119-2231-15 1/10W 22k ohm
R137 119-1031-15 1/10W 10k ohm
R138 119-2231-15 1/10W 22k ohm
R139 119-1031-15 1/10W 10k ohm
R140 119-1001-15 1/10W 10 ohm
R141 119-1041-15 1/10W 100k ohm
R142 119-8231-15 1/10W 82k ohm
R143 119-8231-15 1/10W 82k ohm
R144 119-1041-15 1/10W 100k ohm
R145 032-0140-89 1/10W 47k ohm F
R146 032-0140-89 1/10W 47k ohm F
R147 032-0140-89 1/10W 47k ohm F
R148 032-0140-89 1/10W 47k ohm F
R149 032-0140-89 1/10W 47k ohm F
R150 032-0140-89 1/10W 47k ohm F
R151 032-0140-89 1/10W 47k ohm F
R152 032-0140-89 1/10W 47k ohm F
R153 119-1041-15 1/10W 100k ohm
R155 119-1011-15 1/10W 100 ohm
R156 119-1011-15 1/10W 100 ohm
R157 119-1011-15 1/10W 100 ohm
R158 119-4721-15 1/10W 4.7k ohm
R159 119-4721-15 1/10W 4.7k ohm
R161 119-1001-15 1/10W 10 ohm
R162 119-1011-15 1/10W 100 ohm
R163 119-4721-15 1/10W 4.7k ohm
R164 119-1011-15 1/10W 100 ohm
R165 119-1011-15 1/10W 100 ohm
R166 119-1031-15 1/10W 10k ohm
R167 119-1031-15 1/10W 10k ohm
R168 119-1031-15 1/10W 10k ohm
R169 119-1011-15 1/10W 100 ohm
R170 119-4721-15 1/10W 4.7k ohm
R171 119-1031-15 1/10W 10k ohm
R172 119-1011-15 1/10W 100 ohm
R173 119-1011-15 1/10W 100 ohm
R174 119-1031-15 1/10W 10k ohm
R175 119-1011-15 1/10W 100 ohm
R176 119-1011-15 1/10W 100 ohm
R177 119-1031-15 1/10W 10k ohm
R178 119-1021-15 1/10W 1k ohm
R201 119-1021-15 1/10W 1k ohm
R202 119-1011-15 1/10W 100 ohm
R203 119-2711-15 1/10W 270 ohm
R204 119-2711-15 1/10W 270 ohm
R205 119-2711-15 1/10W 270 ohm
R206 119-1011-15 1/10W 100 ohm
R207 119-2711-15 1/10W 270 ohm
R208 119-2711-15 1/10W 270 ohm
R209 119-2711-15 1/10W 270 ohm
R210 116-6801-15 1/4W 68 ohm
R211 119-1031-15 1/10W 10k ohm
R212 119-1031-15 1/10W 10k ohm
R213 119-4731-15 1/10W 47k ohm
R214 119-1831-15 1/10W 18k ohm
R215 119-1031-15 1/10W 10k ohm
R216 119-1031-15 1/10W 10k ohm
R217 119-1031-15 1/10W 10k ohm
Q104 190-1298-00 2SA1298
Q105 125-2026-95 UN521N
Q106 125-7005-90 PHK04P02T
Q201 193-1306-00 2SD1306
Q202 193-1306-00 2SD1306
Q203 193-1306-00 2SD1306
Q204 193-1306-00 2SD1306
Q205 193-1306-00 2SD1306
Q206 193-1306-00 2SD1306
Q207 193-1306-00 2SD1306
Q208 193-1306-00 2SD1306
Q209 125-0021-95 DTA143ZUA-T106
Q210 125-0021-95 DTA143ZUA-T106
Q211 125-2026-95 UN521N
Q212 125-2026-95 UN521N
Q213 192-4081-00 2SC4081
Q214 192-4081-00 2SC4081
Q301 190-1736-00 2SA1736
Q302 125-2026-95 UN521N
Q303 190-1736-00 2SA1736
Q304 125-2026-95 UN521N
Q305 190-1736-00 2SA1736
Q306 125-2026-95 UN521N
Q401 125-9025-90 HN1C01FU-TE85N
Q501 125-2026-91 UN5211
Q504 192-4081-00 2SC4081
Q505 192-4081-00 2SC4081
Q506 192-4081-00 2SC4081
Q601 190-1298-00 2SA1298
Q602 125-2026-95 UN521N
Q603 101-1143-00 2SB1143
Q604 190-1736-00 2SA1736
Q605 125-2026-95 UN521N
Q606 125-0021-95 DTA143ZUA-T106
Q607 125-0021-95 DTA143ZUA-T106
Q608 190-1736-00 2SA1736
Q609 125-2026-95 UN521N
Q610 190-1298-00 2SA1298
Q611 125-2026-91 UN5211
Q612 101-1143-00 2SB1143
Q613 190-1736-00 2SA1736
Q614 125-2026-95 UN521N
Q615 190-1736-00 2SA1736
Q616 125-2026-95 UN521N
Q617 192-4081-00 2SC4081
Q618 190-1576-00 2SA1576A
Q619 192-4081-00 2SC4081
Q620 190-1298-00 2SA1298
Q621 125-2026-92 UN5212
Q622 102-3420-50 2SC3420GR,BL
Q623 198-0302-50 2SK302 Y,GR
Q624 190-1576-00 2SA1576A
Q625 125-2026-92 UN5212
Q626 125-2026-92 UN5212
Q627 125-2026-92 UN5212
Q628 125-2026-92 UN5212
Q629 190-1736-00 2SA1736
Q630 125-2026-95 UN521N
Q631 125-2026-92 UN5212
R101 119-1041-15 1/10W 100k ohm
R102 119-1011-15 1/10W 100 ohm
R104 119-0000-05 1/10W 0 ohm JW
R105 119-0000-05 1/10W 0 ohm JW
R106 119-1031-15 1/10W 10k ohm
R107 119-1031-15 1/10W 10k ohm
R108 119-1031-15 1/10W 10k ohm
R109 119-1021-15 1/10W 1k ohm
R110 119-1031-15 1/10W 10k ohm
R111 119-1021-15 1/10W 1k ohm
R112 119-2231-15 1/10W 22k ohm
R113 119-2231-15 1/10W 22k ohm
R114 119-1011-15 1/10W 100 ohm
R115 119-4731-15 1/10W 47k ohm
R116 119-1831-15 1/10W 18k ohm
IC458 051-7275-08 TC7W32FU TE12L
IC501 052-7078-01 uPD703276YGJ-
512UENA
IC502 051-9402-68 BR93L56F-W
IC503 051-5440-08 S-80931CNMC-G81
IC504 051-3406-90 NJM2078M
IC505 051-5410-38 BU4820G-TR
IC601 051-2057-00 TB2906HQ
IC602 051-3294-90 TA78DS10F
IC603 051-3335-90 AN77L04M
IC604 051-1855-08 TC7W14F
IC605 051-6600-58 HA12187FP
J101 074-4020-00 ANT
J301 074-1289-80 30p
J302 075-0385-00 JACK
J303 074-1205-93 43P
J501 074-2011-70 20p
J502 074-2001-64 14P
J601 074-1214-00 16P
J602 076-0353-17 PLUG 17P
J603 074-1171-10 10P DIN iPOD
J604 074-1194-00 13P Ce-NET
L101 010-2003-04 30uH COIL
L102 010-2279-50 4.7uH
L103 010-2279-50 4.7uH
L104 010-3105-62 1k ohm/100MHz
L105 010-3105-62 1k ohm/100MHz
L106 010-3105-62 1k ohm/100MHz
L107 010-3105-62 1k ohm/100MHz
L108 010-3109-63 1k ohm/100MHz
L109 010-3105-62 1k ohm/100MHz
L110 010-3105-62 1k ohm/100MHz
L111 010-3103-64 1.5k ohm/100MHz
L112 010-3105-62 1k ohm/100MHz
L113 010-3105-62 1k ohm/100MHz
L201 010-2285-56 2.25k ohm/100MHz
L202 010-2285-56 2.25k ohm/100MHz
L203 010-2285-58 1k ohm/100MHz
L204 010-2285-56 2.25k ohm/100MHz
L205 010-2285-56 2.25k ohm/100MHz
L206 010-2285-58 1k ohm/100MHz
L207 010-3103-64 1.5k ohm/100MHz
L208 010-3103-64 1.5k ohm/100MHz
L209 010-3103-64 1.5k ohm/100MHz
L210 010-3103-64 1.5k ohm/100MHz
L211 010-3103-64 1.5k ohm/100MHz
L212 010-3103-64 1.5k ohm/100MHz
L213 010-3103-64 1.5k ohm/100MHz
L214 010-3103-64 1.5k ohm/100MHz
L301 010-3103-50 1500 ohm/100MHz
L302 010-3103-50 1500 ohm/100MHz
L303 010-3103-50 1500 ohm/100MHz
L305 010-3104-50 30 ohm/100MHz
L306 010-3104-50 30 ohm/100MHz
L307 010-3104-50 30 ohm/100MHz
L308 010-3104-50 30 ohm/100MHz
L309 010-3104-50 30 ohm/100MHz
L310 010-3104-50 30 ohm/100MHz
L311 010-3104-50 30 ohm/100MHz
L312 010-3406-66 NLV25 22uH J
L401 010-3104-50 30 ohm/100MHz
L402 010-2279-50 4.7uH
L403 010-3104-50 30 ohm/100MHz
L404 010-2279-50 4.7uH
L405 010-3104-50 30 ohm/100MHz
L406 010-3104-50 30 ohm/100MHz
L407 010-3104-50 30 ohm/100MHz
L501 010-2279-50 4.7uH
L502 010-2279-50 4.7uH
P201 076-0714-20 20P
P301 076-0349-02 2P
P601 076-0349-02 2P
Q102 190-1298-00 2SA1298
Q103 125-2026-95 UN521N
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION