Clarke FOCUS 00310S User manual

Form No. 71171A 3/08 revised 8/12
U.S. Patent No. 6,105,192; No. RE39,581; No. 6,557,207; No. 7,185,397 and Patents Pending
Canada Patent No. 2,353,279 (Deluxe Machines)
Rider Scrubber
Rotary, Cylindrical and
(Manual Steering)
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your Clarke machine
could result in injury to you or to other personnel; damage to the machine or to other property could
occuraswell. Youmusthavetrainingintheoperationofthismachinebeforeusingit. Ifyouroperator(s)
cannot read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
English (2 - 28)
Español (30 - 56)
Français (58 - 84)
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
ES
EN
FR
Operator’s Manual / Manuel d’utilisation / Libro de Instrucciones
Models: 00310S, 00310C, 00311S, 00311C, 00312S, 00312C,
00317S, 00317C

EN
ENGLISH
Page -2- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
Table of Contents
Operator Safety Instructions....................................................................................................................................................3
Introduction & Machine Specifications.....................................................................................................................................5
Symbols Used on Focus..........................................................................................................................................................6
Display Screens for Focus.......................................................................................................................................................7
Machine Control Panel............................................................................................................................................................8
Machine Controls and Features ..............................................................................................................................................9
How to Prepare the Machine for Operation.............................................................................................................................10
How to Handle the Packed Machine.......................................................................................................................10
How to Unpack the Machine ...................................................................................................................................10
How to Install the Batteries......................................................................................................................................10
Battery Maintenance ...............................................................................................................................................11
How to Charge the Batteries...................................................................................................................................12
Recharging the Batteries.........................................................................................................................................12
Level Indicators for the Charge on the Batteries.....................................................................................................13
How to Install the Squeegee ...................................................................................................................................13
How to Adjust the Squeegee...................................................................................................................................13
How to Change or Rotate Brushes on Cylindrical Brush Head...............................................................................14
How to Install and Remove the Brush or Pad on the Boost Head...........................................................................15
How to Operate the Machine...................................................................................................................................................16
How to Return One Touch to Factory Default Settings............................................................................................16
How to Move Machine.............................................................................................................................................16
Seat Adjustment......................................................................................................................................................16
How to Read the Battery Meter...............................................................................................................................17
How to Change Display Screens on the LCD Module.............................................................................................17
How to Read the Solution Empty Indicator..............................................................................................................17
How to Read the Recovery Full Indicator................................................................................................................17
How to Operate the Squeegee and the Vacuum Motor...........................................................................................18
How to Operate the Solution Flow...........................................................................................................................18
How to Operate Brush Pressure .............................................................................................................................18
How to Operate the Forward / Reverse Switch.......................................................................................................18
How to Fill the Solution Tank...................................................................................................................................19
Operating the Machine............................................................................................................................................19
Do These Procedures When You Begin Your Work Period.....................................................................................20
How to Clean a Floor...............................................................................................................................................21
How to Clean a Very Dirty Floor..............................................................................................................................22
Do These Procedures When You End Your Work Period........................................................................................22
Maintenance............................................................................................................................................................................24
Maintenance to Be Done Every Week ....................................................................................................................24
Battery Inspection and Cleaning .............................................................................................................................24
Cleaning the Recovery Tank and Filter ...................................................................................................................24
Cleaning the Solution Tank and Filter......................................................................................................................25
Manually Draining the Solution Tank.......................................................................................................................25
Vac Assisted Solution Tank Draining.......................................................................................................................25
Squeegee Maintenance ..........................................................................................................................................25
Front Squeegee Blade Replacement......................................................................................................................25
Rear Squeegee Blade Replacement.......................................................................................................................26
Squeegee Maintenance ..........................................................................................................................................26
Cleaning the Vac Hose............................................................................................................................................26
How to Correct Problems in the Machine................................................................................................................................27
Common Error Codes..............................................................................................................................................................28
SECTION II Parts and Service Manual
Final Assembly Drawing......................................................86
Parts List .............................................................87
Main Frame Assembly Drawing (Rotary).............................88
Parts List .............................................................89
Main Frame Assembly Drawing (Cylindrical).......................90
Parts List .............................................................91
Main Frame Assembly Drawing (BOOST)...........................92
Parts List .............................................................93
Optional Side Squeegee Lift (28 & 34 Rotary Models)........94
Parts List .............................................................95
Front Wheel Assembly Drawing and Parts List...................96
Squeegee Lift Assembly Drawing and Parts List.................97
Recovery Tank Assembly Drawing......................................98
Parts List .............................................................99
Solution Tank Assembly Drawing (View 1)..........................100
Parts List (View 1)...............................................101
Solution Tank Assembly Drawing (View 2)..........................102
Parts List (View 2)...............................................103
Steering Column Assembly Drawing ..................................104
Parts List ............................................................105
28” Rotary Brush Head Assembly Drawing and Parts List..106
34” Rotary Brush Head Assembly Drawing and Parts List..107
28” Cylindrical Head Assembly Drawing..............................108
Parts List .............................................................109
32” Boost Head Assembly Drawing.....................................110
Parts List .............................................................111
32” Squeegee Assembly Drawing.......................................112
Parts List .............................................................113
39” Squeegee Assembly Drawing.......................................114
Parts List .............................................................115
41” Squeegee Assembly Drawing.......................................116
Parts List .............................................................117
Front Squeegee Assembly Drawing and Parts List.............118
Front Squeegee Arm Assembly Drawing and Parts List......119
Electrical Panel Assembly Drawing and Parts List..............120
Electrical Connection Diagram ...........................................122
Electrical Schematic ...........................................................126
Accessories and Options.....................................................128
revised 8/10

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 3 -
OPERATOR SAFETY INSTRUCTIONS
DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death.
Read and observe all DANGER statements found in your Owner’s Manual and on your machine.
WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other per-
sonnel; property damage could occur as well. Read and observe all WARNING statements found
in your Owner’s Manual and on your machine.
CAUTION: Failure to read and observe all CAUTION statements could result in damage to the
machine or to other property. Read and observe all CAUTION
DANGER: Failure to read the Operator’s Manual prior to operating or attempting any service or maintenance procedure
to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other
property could occur as well. You must have training in the operation of this machine before using it. If your
operator(s) cannot read English, have this manual explained fully before attempting to operate this machine.
DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not
operate this machine unless it is completely assembled. Inspect the machine carefully before operation. Oper-
ate only when lids, doors and access panels are securely closed.
DANGER: Machines can cause an explosion when operated near flammable materials and vapors. Do not use this ma-
chine with or near fuels, grain dust, solvents, thinners, or other flammable materials. This machine is not suitable
for picking up hazardous dust or flammable materials. Use only commercially available floor cleaning waxes
intended for machine operation. DO NOT put gasoline, combustible or flammable materials in the solution or
recovery tank.
DANGER: Lead acid batteries generate gases which can cause an explosion. Keep sparks and flames away from batteries.
Do not smoke around the machine. Charge the batteries only in an area with good ventilation.
DANGER: Working with batteries can be dangerous! Always wear eye protection and protective clothing when working near
batteries. Remove all jewelry. Do not put tools or other metal objects across the battery terminals, or the tops of
the batteries.
DANGER: Using the charger with a damaged power cord could result in an electrocution. Do not use the charger if the
power cord is damaged.
WARNING: This machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge.
WARNING: While on ramps or inclines, avoid sudden stops. Avoid abrupt sharp turns. Use low speed down ramps. Clean only
while descending (driving down) the ramp.
WARNING: Do not turn the machine on a ramp. Do not use on surfaces having a gradient exceeding that marked on the appliance.
WARNING: Machines can topple over and cause injury or damage if guided over the edges of stairs or loading docks. Stop and
leave this machine only on a level surface. When you stop the machine, put all switches into their “OFF” position. Turn
the key switch “OFF” and remove the key.
WARNING: Skidding may occur when traveling at high speeds and attempting sharp turns, especially on wet surfaces.
revised 8/12

EN
ENGLISH
Page -4- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
WARNING: Do not move machine with forklift. Damage could occur to machine.
WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must
be performed by authorized Clarke personnel only.
WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other by-
standers. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities.
WARNING: Electrical components of this machine can “short-out” if exposed to water or moisture. Keep the electrical components of
the machine dry. Wipe the machine down after each use. This appliance is for dry use only and is not to be used or stored
outdoors in wet conditions. For storage, keep the machine in a building.
WARNING: Operating a machine without observing all labels and instructional information could result in injury or damage. Read all
machine labels before attempting to operate. Make sure all of the labels and instructional information are attached or fastened
to the machine. Do not cover them for any reason. If labels or decals are missing or become damaged, get replacement labels
and decals from your Clarke distributor immediately.
WARNING: Wet floor surfaces can be slippery. Water solutions or cleaning materials used with this type of machine can leave wet areas
on the floor surface. These areas can cause a dangerous condition for the operator or other persons. Always put “Caution”
signs around/near the area you are cleaning.
WARNING: Improper discharge of waste water may damage the environment and be illegal.
The United States Environmental ProtectionAgency has established certain regulations regarding discharge of waste water.
City, state and national regulations regarding this discharge may also be in effect in your area. Understand and follow the
regulations in your area. Be aware of the environment hazards of chemicals that you dispose.
WARNING: Only use the brushes provided with the appliance or those specified in the Operator’s Manual. The use of other brushes may
impair safety.
CAUTION: Use of this machine to move other objects or to climb on could result in injury or damage. Do not use this machine as a step or
furniture.
CAUTION: Your machine warranty will be voided if anything other than genuine Clarke parts are used on your machine. Always use
Clarke parts for replacement.
CAUTION: This machine contains lead acid batteries. The batteries must be disposed of in an environmentally acceptable manner.
WARNING: GENERAL SAFETY RULES
The rules below have to be followed carefully in order to avoid injury to the operator and damage to the
machine:
• During the operation of this machine, pay attention to other people around you, especially children.
• Use care when reversing machine in confined areas.
• Do not mix different kinds of detergents. Avoid harmful odors.
• Do not place any liquid containers on to the machine.
• The recommended operating temperature should be between 32° F and 104° F.
• The humidity for operating this machine should be between 30 and 95%.
• Do not use acid solutions that could damage the machine.
• In order to prevent floor damage, do not leave brushes running when machine is standing still.
• In case of fire, use a powder extinguisher. Do not use water.
• Do not strike shelving or scaffoldings, where there is danger of falling objects.
•Adapt the utilization speed to the adhesion conditions.
• Do not exceed the declared hill climbing capacity, otherwise the machine could become unstable.
• For any maintenance operation take off the power supply from the machine.
• Do not disassemble any parts which require the use of a tool to be removed.
• Do not wash the machine with direct water jets or with high water pressure nor with corrosive material.
•After every 200 working hours have machine checked by an authorized service person.
revised 8/12

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 5 -
Model 28” Disc 34” Disc 28” Cylindrical 32” Boost® Orbital
Part Number 00310S, 00310C 00311S, 00311C 00312S, 00312C 00317S, 00317C
Cleaning Swath 28” (71.1 cm) 34” (86.4 cm) 28” (71.1 cm) 32” (81.3 cm)
Power Supply 36 volt system using (6) 6 volt 250, 330, or 370AH deep cycle batteries
Battery Charger On-Board fully automatic smart charger, 115V 60 Hz or 230V 50 Hz
Brush Motors (1) 2 hp (1.5 kW) driving (1) 2.5 hp (1.9 kW) driving (2) .75 hp (.56 kW) (1) .75 hp (.56 kW)
two right angle gearboxes two right angle gearboxes
Brush Size / Speed (2) 14” (36 cm) 300 RPM (2) 17” (43 cm) 300 RPM (2) 6 x 28” (15.2 x 71.1 (1) 14 x 32” (35.6 x 81.3
cm) 750 RPM cm) 2250 RPM
Brush Pressure 12 -225 lbs. (57-102 kg) 90-130 lbs. (41-59 kg) 115-155 lbs. (52-70 kg)
Traverse Speed (max) 4.1 mph (6.6 kph)
Traverse 1.5 hp (1.1 kW) transaxle powering of two 10” (25.4 cm) diameter rear wheels
Max. Cleaning Grade 6 degree
Vacuum Motor 1 hp (.75 kW) 3 stage tangential discharge
Noise Level 70 dBA
Solution Tank 30 gallon (113 liter)
Recovery Tank 30 gallon (113 liter)
Length 65” (165 cm)
Width 33” (84 cm) 35.5” (90 cm) 30” (130 cm) 33” (84 cm)
Height 56” (142 cm)
Machine Weight
w/330AH batteries 1478 lbs. (670 kg) 1498 lbs. (679 kg) 1498 lbs. (679 kg) 1488 lbs. (675 kg)
& full of solution
Warranty 8 years PolydurTM tanks, 3 years parts, 1 year labor, 18 months pro-rated batteries
Introduction
Introduction & Machine Specifications
This is a floor cleaning machine which, using the mechanic or abrasive action of brushes or pads and the chemical action of a water-
detergent solution, is able to clean any type of floor. During its forward movement, it picks up the removed dirt and the detergent
solution which has not been absorbed by the floor.
WARNING: The Products sold with this Manual contain or may contain chemicals that are known to certain governments (such
as the State of California, as identified in its Proposition 65 Regulatory Warning Law) to cause cancer, birth defects or other repro-
ductive harm. In certain locations (including the State of California) purchasers of these Products that place them in service at an
employment job site or a publicly accessable space are required by regulation to make certain notices, warnings or disclosures
regarding the chemicals that are or may be contained in the Products at or about such work sites. It is the purchaser’s responsibility
to know the content of, and to comply with, any laws and regulations relating to the use of these Products in such environments. The
Manufacturer disclaims any responsibility to advise purchasers of any specific requirements that may be applicable to the use of the
Products in such environments.
revised 8/10

EN
ENGLISH
Page -6- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
WARNING
READ OPERATOR’S
MANUAL BEFORE OPERATING
THIS MACHINE
RISK OF FIRE
• Use only commercially available
floor cleaners and waxes intended for
machine operation.
• Do not use flammable materials.
RISK OF INJURY OR DAMAGE TO
MACHINE
• Do not turn, stop or leave machine
on a ramp or dock. 71018A
Brush Up/Down
Squeegee
Up/Down
Solution Flow
Switch
Battery Meter
LCD Display
Button
One Touch
Button
Forward /
Reverse
Horn
On/Off Switch
Recovery /
Solution LED
Symbols Used On FOCUS Rider

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 7 -
Traverse speed indicator
1 = low 0-2 mph
2 = med 0-3 mph
3 = high 0-4 mph
Position arrow indicating current position
of squeegee (up or down)
Indicators are on,
showing current set-
tings.
Screens
Available
to Operator
“Battery” blinks when
low voltage occurs.
Water “droplets” off when solution is off and
they are flashing when solution is on.
Arrows indicating vacuum sta-
tus. They are flashing when vac
is on and off when vac is off.
SCREEN 1
SCREEN 2
Example
SCREEN 3 (Diagnostic)
The Diagnostic only. It will not show unless a fault with
the machine occurs. When the fault happens the icon
and error code will be displayed.
Display Screens For FOCUS Rider

EN
ENGLISH
Page -8- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
A
B
C
D
E
E, F
Machine Control Panel
On/Off Key Switch (See figure 1, Item D)
The key switch turns “ON” the power to the control panel. “O”
is the “OFF” and “I” is the “ON”.
Brush Up/Down Switch (See figure 1, ItemA)
To lower brush head, push the brush switch in the down (+)
position. To lower the brush head to maximum brush pressure,
continue to hold the switch in the down (+) position until the
travel stops. The brush motors will start and solution will flow
(provided the solution is turned “ON”) when the machine begins
to traverse. To raise the brush head, push the brush switch in
the up (-) position until the brush head travel stops or desired
position is reached.
Squeegee Up/Down Switch (See figure 1, Item B)
The squeegee switch is used to raise and lower the squeegee
and to turn on and off the vacuum motor. The vacuum motor
is turned on when the switch is placed in the middle or lower
position. NOTE: When the squeegee switch is placed in the
lower position, the vacuum motor will turn on.
To raise the squeegee, place the switch in either the middle or
up position. The middle position is used for one touch control.
The vacuum motor will stop, after a short delay, when the
switch is placed in the up position.
Hour Meter (See figure 1, Item E)
The hour meter is located on the front display. You must toggle
screens using LCD display button. The hour meter indicates
the number of hours the machine has operated. It displays
brush motor, vacuum motor, traverse motor and total key on
times.
Battery Meter (See figure 1, Item F)
The battery meter indicates the relative charge on the battery
pack. The battery meter is located on screen 1 on the front
display. See page 7.
Solution Flow Control (See figure 1, Item C)
The solution flow switch regulates the flow of chemical solution
to the floor. To increase the flow, toggle (+). To decrease the
flow, toggle (-). To shut off the solution, toggle - until no indica-
tors are visible on display. NOTE: DO NOT run dry!
NOTE: No solution will flow when the machine does not
traverse.
Circuit Breakers
The circuit breaker reset buttons are located on the back side
of the front cover below front display. The breakers are as
follows:
ItemA- Main (5 amp)
Item B - Key Switch (5 amp)
Figure 1

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 9 -
Machine Controls and Features
Recovery Tank Float
The FOCUS Rider Scrubber is equipped with a float that shuts the vacuum off
when the recovery tank is full. The squeegee will no longer pick up water. If
this should happen, raise the squeegee and empty the recovery tank.
The Traverse
The FOCUS Rider Scrubber is equipped with an electronically controlled
traverse system with variable speeds in forward and reverse.
1. To traverse the machine, the power to the machine must be turned on
with the key switch and the operator must be properly seated.
2. The traverse speed can be adjusted by varying the pressure on the foot
pedal.
NOTE: During reverse motion, the squeegee raises and the solution flow
stops automatically. Reverse also reduces maximum traverse speed.
Brakes
The machine is equipped with an electronic braking system. The electronic
braking is activated automatically. NOTE: During training, you should allow
machine to come to a full stop until you become familiar with stopping distances
required.
Parking Brake
The parking brake is activated automatically when the machine comes to a
stop. It disengages automatically when you begin to traverse. The transaxle is
equipped with a manual brake release. NOTE: Machine will not function when
manual brake release is engaged. See figure 2.
ReverseAlarm
The reverse alarm will sound intermittently and automatically when the machine
is in reverse.
Figure 2

EN
ENGLISH
Page -10- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
BATTERY CONNECTIONS
Front of
machine
235 AH, 6 Volt
(Battery No. 881317 Wet)
(Battery No. 881318 Dry)
Three (3) 70222A Spacers
310 AH, 6 Volt
(Battery No. 56391391 Wet)
305 AH, 6 Volt
(Battery No. 891385 Dry)
420 AH, 6 Volt
(Battery No. 56388582 Wet)
375 AH, 6 Volt
(Battery No. 40602A Dry)
Front of
machine
Front of
machine
How To Prepare the Machine For Operation
How To Handle the Packed Machine
The machine is packed in a specific package provided on a pallet so that
it can be moved with a forklift.
WARNING: The packages cannot be placed on top of
each other.
How to Unpack the Machine
1. Remove the outer package.
2. The machine is fixed on the pallet with banding straps and
wooden blocks to prevent movement during shipment. Remove
the bands and blocks.
3. The machine is shipped with the batteries already installed.
4. Remove tie down brackets.
5. Lower the ramp. The machine can be driven off of the pallet if
the operator is thoroughly familiar with its operation. Avoid violent
blows to the base unit.
6. Keep the pallet for future transport necessities.
How to Install the Batteries
WARNING: The batteries are heavy. Lifting batteries
without help could result in an injury. Get
help to lift the batteries.
WARNING: Working with batteries can be dangerous.
Always wear eye protection and protective
clothing when working near batteries. NO
SMOKING!
WARNING: Hydrogen gas is formed during the charging
operation and is explosive. Only charge bat-
teries in a well ventilated area with the seat
base lifted.
The batteries are fitted in the battery compartment under the seat and
recovery tank (figure 3). The machine uses six - 6 volt batteries. They
must be handled by using appropriate lifting equipment suitable for the
weight and for the coupler system. For maintenance and daily recharge
of the batteries, it is necessary to follow all instructions given by the
manufacturer.
For Battery Installation follow these steps (See figure 3):
1. Make sure that the key switch is in the “OFF” position.
2. Lift and rotate the base support of the seat forward.
3. Lean the seat on it’s restraint cable.
4. Lift the front of the recovery tank and rotate it towards the rear
until it rests on it’s restraint cable.
5. Put the batteries into position and connect the battery cables as
shown in figure 3.
6. Rotate the recovery tank and then carefully rotate it forward to the
normal operating position.
7. Lower the base support of the seat.
NOTE: Charge the batteries before using.
Figure 3
revised 1/11

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 11 -
Correct Fill
How To Prepare the Machine For Operation
Battery Maintenance
The electrical power to operate the machine comes from the storage batteries.
Storage batteries need preventative maintenance.
WARNING: Working with batteries can be dangerous. Always
wear eye protection and protective clothing when
working near batteries. NO SMOKING!
To maintain the batteries in good condition, follow these instructions:
1. Keep the electrolyte at the correct level. The correct level is between
1/4” (1/2 cm) below the bottom of the tube in each cell and above the
tops of the plates. Check the level of the electrolyte each time you
charge the batteries (see figure 4).
NOTE: Check the level of electrolyte prior to charging the batteries. Be sure
the plates in each cell are covered with electrolyte before charging. Do
not top off the cells prior to charging the battery. Electrolyte expands
during charging. As a result, the electrolyte could overflow from the
cells. Always top off the cells with distilled water after charging.
CAUTION: Irreversible damage will occur to the batteries if
electrolyte does not cover the plates. Keep the
electrolyte at the correct level.
CAUTION: Machine damage and discharge across the tops
of the batteries can occur if the batteries are over
filled. Do not fill the batteries up to the bottom
of the tube in each cell. Wipe any acid from the
machine or the tops of the batteries. Never add
acid to a battery after installation.
CAUTION: Batteries must be refilled with distilled water only.
Do not use tap water as it may contain contami-
nants that will damage batteries.
2. Keep the tops of the batteries clean and dry. Keep the terminals and
connectors clean. To clean the top of the batteries, use a damp cloth
with a weak solution of ammonia or bicarbonate of soda solution. To
clean the terminals and connectors, use a terminal and connector clean-
ing tool. Do not allow ammonia or bicarbonate of soda to get into the
batteries.
3. Keep the batteries charged.
Figure 4

EN
ENGLISH
Page -12- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
(Shown with Optional Chemical Mixing System)
ABC
How To Prepare the Machine For Operation
How to Charge the Batteries
WARNING: Charging the batteries in an area without ad-
equate ventilation could result in an explosion.
To prevent an explosion, charge the batteries
only in an area with good ventilation.
WARNING: Lead acid batteries generate gases which could
explode. Keep sparks and flames away from
batteries. NO SMOKING!
CAUTION: See Charger Owner’s Manual. All onboard
battery chargers are programmed for a specific
type battery. The charger may need reprogram-
ming to properly charge replacement batteries
different than the originally equipped Clarke
battery.
NOTE: Only replace batteries with the identical Clarke battery pack as
originally equipped. The correct Clarke battery part number can be
found on the Clarke battery label affixed to the top of each battery.
If the replacement battery is a different Clarke battery, please con-
tact Clarke Technical Service, 1-800-356-7274, for instructions.
If the replacement battery is not a Clarke battery, please contact the
charger manufacturer for instructions.
To charge the batteries, follow this procedure:
1. Make sure the key switch is in the “OFF” position.
2. Raise the seat base support.
3. Connect the battery chargerAC cord to a 15 amp (min) 120V properly
grounded wall receptacle.
4. Observe indicator light to ensure the charging process has started
(see figure 5,A- Red, B - Yellow, and C - Green ). For color indica-
tions see figure 6.
Recharging the Batteries
The Focus Rider Scrubber comes with an on board charger.
1. Plug into any wall socket and charging is automatic.
2. Observe indicator light to ensure the charging process has started
(see figure 5,A- Red, B - Yellow, and C - Green ). For color indica-
tions see figure 6.
NOTE: Make sure you plug into a circuit that is not loaded by other equip-
ment. Wall breakers may be tripped and no charge will occur.
WARNING: Never charge a GEL battery with an unsuitable
battery charger. Carefully follow the instruc-
tions given by the manufacturer of the batteries
and battery charger.
NOTE: To prevent permanent damage to the batteries, avoid their complete
discharge. Never leave the batteries completely discharged, even if the
machine is not being used. When recharging the batteries, keep the base
support of the seat lifted. After every 20 recharging operations, check the
level of the electrolyte and if necessary top off with distilled water.
Figure 5
Figure 6

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 13 -
Figure 8
Figure 9
Figure 10
3/16” minimum
A
B
How To Prepare the Machine For Operation
Level Indicators for the Charge of the Batteries
The battery meter ( see figure 7) on the control panel has a digital read out
with 10 fixed positions (A) and also a blinking indicator (B). The bars that
appear on the display show the approximate charge level with icon (blink-
ing) discharged battery.
NOTE:Afew seconds after the voltage reads 32V it will start blinking. The
brush motors will then automatically switch off.
How To Install the Squeegee
To install the squeegee onto the machine, follow this procedure:
1. The squeegee assembly has a break away feature that is also used
for mounting the squeegee. Loosen the knobs on the squeegee
(figure 8). Slide the stud into the slotted hole in the support frame
on the machine.
2. Attach the vacuum hose cuff to the squeegee hose fitting (see figure
9).
3. Tighten knobs. NOTE: Do not overtighten or break away feature
is lost and damage may occur.
NOTE: To prevent damage to the squeegee or machine, the squeegee was
designed to break away from the machine. If the squeegee is impacted
and it breaks away from the machine, simply reinstall it by following step
1-3.
How toAdjust the Squeegee
During operation, the rear squeegee blade should have a constant 3/16”
minimum flare along the entire squeegee blade (see figure 10).
1. The squeegee body can be tilted to adjust the squeegee blade flare
in the middle to match the flare on the ends. To adjust the tilt, loosen
the adjusting bolt located on the left and right side of the squeegee
(see figure 9).
2. Press down on the squeegee until both sets of guide wheels contact
floor.
3. After making adjustments, retighten the screw(s).
NOTE: It is important that the right and left wheels are contacting the floor
in order for the squeegee to work.
NOTE:As the rear squeegee blade wears, it can be rotated and/or flipped
to obtain four good edges before having to change blades.
Figure 7

EN
ENGLISH
Page -14- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
How To Prepare the Machine For Operation
How To Change or Rotate Brushes on Cylindrical Brush Head
To install or rotate brushes on the cylindrical brush head:
1. Raise the brush deck and turn the key switch “OFF”.
2. Raise the brush skirt and pull out to remove. See figure 11.
3. Remove thumb screw from brush door. See figure 12.
4. Lower door approximately 1/2 inch and slide door and hub
assembly from brush. See figure 13.
5. Slide brush off hub at opposite end. See figure 14.
6. Rotate brush or replace.
7. Slide brush on drive hub and insert door and hub assembly
into brush core.
8. Raise door and install thumb screw.
9. Place side skirt on retainer pins and lower in place.
Figure 11
Figure 12
Figure 13
Figure 14

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 15 -
How To Prepare the Machine For Operation
How To Install The Brush Or Pad on the BOOST machine
To install the brush or pad on the BOOST machine, follow this pro-
cedure:
1. Turn the key switch “ON”.
2. Put the brush switch in the “UP” position.
3. Turn the key switch “OFF”.
4. Go to the side of the machine.
5. Press on a brush or pad under the flex plates. See figure 15.
NOTE: When using a black pad, position pad on head.
Lower head and operate momentarily to affix pad to
pad driver (if you have difficulty, position pad on
floor and lower head then operate.)
How To Remove The Brush Or Pad on the BOOST
machine
To remove the brush or pad from the machine, follow this proce-
dure:
1. Turn the key switch “ON”.
2. Put the brush switch in the “UP” position.
3. Turn the key switch “OFF”.
4. Go to the side of the machine.
5. Pull downward on the brush or pad until it releases from the
flex plates. See figure 16.
Figure 15
Figure 16

EN
ENGLISH
Page -16- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
How To Operate The Machine
How to Return One Touch to Factory Default Settings
To restore the factory settings, follow the procedures below:
1. Press and hold the green one touch button (figure 17) until you
hear a double beep from the machine. NOTE: The time re-
quired for this will be approximately 15 seconds.
2. Thesettingsshouldbereturnedto 2 bars of solution and1barof
brush pressure. NOTE: The squeegee vac switch must be in
the middle position for default settings to work.
How to Move the Machine Without Power (see figure 18)
1. Engage manual override on brake (see page 9, “Parking
Brake”).
2. Remove foot plate and 4 screws and locate steering motor.
3. Using the knob on steering motor, turn shaft on motor in direc-
tion you wish to turn machine.
4. Slowlypushmachine to desired location. NOTE: If you attempt
to push machine too fast it will limit top speed. If this hap-
pens, stop and restart.
5. After moving machine, disengage manual brake override.
NOTE: Machine will not function if override is engaged.
SeatAdjustment (Standard)
The standard seat is not adjustable forward or backward.
SeatAdjustment (Deluxe)
The optional deluxe seat is adjustable in three ways:
1. The seat can be adjusted to the forward/backward position by
using the lever on the lower right side of the seat . Moving the
lever will allow the seat to slide into the preferred position. See
figure 19.
2. To adjust the angle of the back support portion of the seat, turn
the lever located in the middle right position of the seat. Turning
thisclockwise will make the seat morevertical. Turningtheknob
counterclockwise will tilt the seat back.
See figure 20A.
3. Toadjustthesuspensionoftheseatforoperatorcomfort,usethe
leverontheside ofthe backsupportsectionofthe seat.Thishas
three positions. The upper position is for light weight operators.
Themiddle position is for medium weight operators. Thebottom
position is for heavy weight operators. See figure 20, B. NOTE:
The lever must be pressed firmly to change positions.
Figure 17
Figure 18
Figure 19
Figure 20

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 17 -
Figure 21
Figure 22
Figure 23
A
SCREEN 1
SCREEN 2
A
B
B
How To Operate the Machine
How to Read the Battery Meter (see figure 21,A)
The battery meter is an indicator on the LCD display. This indicator is
on the LCD display on the front of the machine. It has 10 bars with 10
bars visible indicating a full charge. As you run the machine the bars
will begin to lower. The “Battery Icon” (B) will begin to flash to indicate
you are reaching the end of charge.
NOTE: If you continue to run the brushes they will shut down to
protect the batteries from over discharging.
NOTE: Run times will vary depending on machine variables, bat-
tery size, brush pressure and floor type, etc.
How to Change Displays Screens on the LCD Module
The LCD display has three screens. Two of them can be accessed at
any time the key is on. The first screen shows the machine status and
the second screen shows the four hour meters (figure 21).
The two screens that can be viewed by the operator can be accessed
via the display button (figure 22) on the control panel to the left of the
key switch. Pressing this button toggles the display between the avail-
able screens.
The third screen is for diagnostics only. This screen displays any errors
that might occur or if the system diagnostics finds something wrong.
When the diagnostic screen comes up, refer to the trouble shooting
guide for suitable action to resolve the error code.
How to Read the Solution Empty Indicator (see figure 23,A)
The solution empty indicator is located on the front of the machine
below the LCD display. When the solution reaches nearly empty, the
indicator will begin to flash, warning the operator of the need to refill.
NOTE: Solution run times will vary depending on solution flow
setting.
How to Read the Recovery Full Indicator (see figure 23, B)
The recovery full indicator is located on the front of the machine below
the LCD display. When the recover tank is near full the indicator will
begin to flash, warning the operator of the need to empty the recovery
tank. The vacuum motors will shut down a few moments later.
NOTE: Recovery times will vary depending on

EN
ENGLISH
Page -18- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
A
B
How To Operate the Machine
How to Operate the Squeegee and the Vacuum Motor
The squeegee wipes the floor while the vacuum motor removes the dirty
solution from the floor. To operate the squeegee, follow this procedure:
1. To lower the squeegee and start the vacuum motor, press the
squeegee up/down switch to the down position (figure 24).
NOTE: The vacuum motor will start immediately when the
down position of the switch is pressed, and the squeegee
will lower.
2. To raise the squeegee, press the squeegee up/down switch to
the up position (figure 24). The squeegee will then raise and the
vacuum motor will shut off after short delay NOTE: The center
position of the squeegee up/down switch is for use with one
touch control.
NOTE: The squeegee will raise automatically when traversing in
reverse during scrubbing operations.
How to Operate the Solution Flow
Thesolutionisusedtoloosenandremovedirtfromthefloor. Theamount
of solution applied can be adjusted to five different levels to accommo-
date many different floor conditions. These different levels are shown
on the LCD display on the front of the machine. To adjust the amount of
solution applied, use the Solution Flow Switch (figure 25). NOTE: There
are five different settings on the display. See figure 26, A.
To increase solution flow:
1. Press the “ + ” side of the switch (figure 25).
2. Press and hold the “ + ” switch to achieve the desired level of solu-
tion flow.
To decrease solution flow:
1. Press the “ - “ side of the switch (figure 25).
2. Press and hold the “ - “ side of the switch to achieve the desired
level of solution flow.
How to Operate the Brush Pressure
Thebrushesare usedtosupply agitationforthesolution, whichimproves
the cleaning process. The amount of brush pressure applied can be
adjustedto five differentlevels toaccommodate manydifferent floorcon-
ditions. These different levels are shown on the LCD display on the front
of the machine (figure 26, B). To adjust the amount of brush pressure,
use the brush up/down switch (figure 27).
To increase brush pressure:
1. Press the “ + ” side of the switch (figure 27).
2. Press and hold the “ + ” switch to achieve maximum level of pres-
sure.
To decrease brush pressure:
1. Press the “ - “ side of the switch (figure 27).
2. Pressand holdthe“ -“side oftheswitch toachieveminimum orno
brush pressure.
Figure 24
Figure 25
Figure 26
Figure 27

EN
ENGLISH
Clarke®Operator’s Manual (EN) - Focus Rider Form No. 71171A - 19 -
How To Operate the Machine
How to Operate the Forward / Reverse Switch
(see figure 28).
1. To go forward, push the up arrow side of the switch.
2. To go in reverse, push the down arrow side of the switch.
How to Fill the Solution Tank
The solution tank fill port is located at the left side of the machine (see figure
29). To fill the solution tank, follow this procedure:
1. Turn the key switch to the “OFF” position.
2. Remove lid.
3. Add a cleaning chemical to the solution tank. For the correct amount of
chemical, follow the directions shown on the container. NOTE: Excess
foam in the recovery tank could damage the vacuum motor, so use
only the minimum amount of detergent necessary.
WARNING: Always use low foam detergent. To avoid the
production of foam, before starting to clean,
put a minimum quantity of antifoam liquid into
the recovery tank. NEVER USE PURE ACID.
4. Fill the solution tank with clean water (see figure 29).
5. After filling the solution tank, replace the solution tank lid.
WARNING: Water solutions or cleaning materials used
with this type of machine can leave wet areas
on the floor surface. These areas can cause a
dangerous condition for the operator or other
persons. Always put CAUTION signs near the
area you are cleaning.
WARNING: Machines can ignite flammable materials and
vapors. Do not use with or near flammables
such as gasoline, grain dust, solvents and
thinners. Only use a cleaning concentration
recommended by the chemical manufacturer.
WARNING: Clarke recommends a maximum water tem-
perature of 120°F (49°C).
Operating the Machine
NOTE: Before scrubbing with the machine, become familiar with the opera-
tions and handling of the machine. Run the machine at the lowest traverse
speed. Use the machine in an area that has no furniture or objects until you
can do the following:
1. Traverse the machine in a straight direction, forward and backward.
2. Stop the machine safely.
3. Turn the machine both left and right and return to a straight direction.
4. Turn a 180oturn where one rear wheel just pivots.
Figure 28
Figure 29

EN
ENGLISH
Page -20- Form No. 71171A Clarke®Operator’s Manual (EN) - Focus Rider
Figure 30
Figure 31
Figure 32
How To Operate the Machine (cont.)
To traverse the machine follow this procedure:
1. Sit on the driver seat. NOTE: The machine will not traverse if the
operator is not properly seated.
2. Turn the key switch to the “ON” position.
3. Raise the brush to the highest position (if necessary).
4. Raise the squeegee (if necessary).
5. Gently press the foot pedal and the machine will begin to move.
6. To stop, release pressure on the foot pedal.
7. To travel in reverse, select reverse with the forward/reverse switch.
8. To stop, release pressure on the foot pedal.
9. When you stop the machine, turn the key switch “OFF” and remove
the key.
Do These Procedures When You Begin Your Work Period
1. Make sure the key switch is in the “OFF” position.
2. DisconnectAC power from battery charger (follow charger instruc-
tions).
3. Make sure the filter screen (1) to the vacuum motor is clean and
installed properly in the recovery tank (see figure 30).
4. Make sure the recovery tank lid is in place and has been tightened
(see figure 31).
5. Close and secure the lower cleaning port cover (if so equipped) on
the recovery tank.
6. Make sure that the plug in the recovery drain hose is in place and
has been tightened (see figure 32).
7. Make sure that the brushes/pads are in position and installed cor-
rectly.
8. Make sure the brush housings are in position on the brush head.
9. Check the installation of the squeegee and squeegee hose.