Clarke IMAGE 16 I User manual

Electronic Service
Manuals
This electronic document is provided as a service to our customers.
Wedonotcreatethecontentsoftheinformationcontainedinthisdocu-
ment. Shouldyouhavedetailedquestionspertainingtotheinformation
contained in this document, you may contact Michco, or the manufac-
turer which provided the original information in this electronic deliver-
able. Michco’sonlypartin this electronic deliverable was the electronic
assemblyprocess. Byprovidingthismanualonlinewearenotguaran-
teeing parts availability.
You may contact Michco through the following methods:
Phone [phone] or [phone]
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: [phone]
Email: [email protected]
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email: [email protected]
By Fax: [phone]
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.
ManualsaresubjecttoManufacturer’sreproductionlimitations. Originalsorreproductionswereprovidedbymanufacturers
through a request. We make no warranty as to the correctness of information provided in this document and you assume
allrisk. By placing thesemanualsonlinewe are notdeclaringourcorporation to be anmanufacturerauthorizeddealer or
provider, please check ourwebsiteforauthorizedmanufacturerswerepresent.

Form No. 70670A 12/05 Clarke®Printed in the U.S.A.
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your Clarke machine
couldresultininjurytoyouortootherpersonnel;damagetothemachineortootherpropertycouldoccur
aswell. Youmusthavetrainingintheoperationofthismachinebeforeusingit. Ifyouroperator(s)cannot
read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: Clarke®, 2100 Highway 265, Springdale, Arkansas 72764.
Operator'sManual
Manueld'utilisation
Librode Instrucciones
IMAGE 16 I/IX 120V
®
English (2 - 14)
Español (16 - 28)
Français (30 - 42)
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
ES
EN
FR
U.S. Patent No. 5,383,251; No. 6,418,586 (ix modesl only); No. 6,968,594

EN
ENGLISH
-2- Clarke®Operator's Manual (EN) - Image 16 I/IX 120V
Table of Contents
OperatorSafetyInstructions............................................................................................................. 3
Introduction&Machine Specifications .............................................................................................. 4
MachinesGroundingInstructions ..................................................................................................... 5
MachineControls ............................................................................................................................. 6
HowToPreparethe Machine for Operation....................................................................................... 7
HowtoCleanCarpet ........................................................................................................................ 8
Operator'sMaintenance ................................................................................................................... 9
Maintenance .................................................................................................................................... 10
AuthorizedPersonnelMaintenance .................................................................................................. 12
Howto Correct Problemsinthe Machine ......................................................................................... 14
Section II:
FinalAssembly Drawing Image 16i/ixErgoEX .................................................................................. 44
Parts List ............................................................................................................................ 45
Recovery TankAssembly Drawings & Parts List .............................................................................. 46
Brush HousingAssembly Drawing & Parts List ................................................................................ 47
ElectricAssembly Drawing & Parts List Image 16i ErgoEX .............................................................. 48
ElectricAssembly Drawing & Parts List Image 16ix ErgoEX............................................................. 49
Recovery Shoe Assembly Drawing & Parts List i/ix ErgoEX ............................................................ 50
ValveAssembly Drawing &Parts List 16iErgoEX............................................................................. 51
Vavle Assembly Drawing & Parts List 16ix ErgoEX........................................................................... 52
Motor Drawing & Parts List .............................................................................................................. 53
AuthenticClarke Products ............................................................................................................... 54
ElectricalSchematic Image 16i/ix ErgoEX120V .............................................................................. 55
ConnectionDiagramImage16i/ixErgoEX120V ............................................................................... 56
FlowDiagram Image 16i ErgoEX ...................................................................................................... 57
FlowDiagram Image 16ix ErgoEX .................................................................................................... 58

EN
ENGLISH
Clarke®Operator's Manual (EN) - Image 16 I/IX 120V - 3 -
IMPORTANT SAFETY INSTRUCTIONS
DANGER: Failureto read and observe all DANGER statements could result in severe bodily
injuryor death. Read and observe all DANGERstatements found in your Owner's
Manual and on your machine.
WARNING: Failureto read and observe all WARNING statements could result in injury to you
or to other personnel; property damage could occur as well. Read and observe all
WARNINGstatements found in your Owner'sManual and on your machine.
CAUTION: Failure to read and observe all CAUTION statements could result in damage to the
machine or to other property. Read and observe all CAUTION statements found in
your Owner's Manual and on your machine.
WARNING: To reduce the risk of fire, electric shock, or injury:
1. Donotleaveappliancewhen plugged in. Unplugfromoutletwhennot inuseandbefore
servicing.
2. To reduce the risk of electric shock use indoors only.
3. Do not allow to be used as a toy. Close attention is necessary when used by or near
children.
4. Use onlyas describedin themanual. Use onlymanufacturer's recommendedattach-
ments.
5. Do not use with damaged cord or plug. If appliance is not working as it should, has
beendropped,damaged,leftoutdoors,ordroppedintowater,returnittoaservice
center.
6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord
aroundsharpedgesor corners. Do not run applianceovercord. Keep cord away from
heatedsurfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Donot handle plug orappliance with wet hands.
9. Do not put any object into openings. Do not use with any opening blocked; keep free
of dust, lint, hair and anything that may reduce air flow.
10. Keephair, looseclothing, fingers,and allparts ofbody awayfrom openingsand moving
parts.
11. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or
hot ashes.
12. Do not use without filters in place.
13. Turnoffallcontrolsbeforeunplugging.
14. Use extra care when cleaning on stairs.
15. Do not use to pick up flammable or combustible liquids such as gasoline or use in
areaswhere they maybe present.
16. Connecttoproperly groundedoutlet. See"GroundingInstructions".
SAVE THESE INSTRUCTIONS

EN
ENGLISH
-4- Clarke®Operator's Manual (EN) - Image 16 I/IX 120V
INTRODUCTION AND MACHINE SPECIFICATIONS
The Image 16 is an extractor for cleaning the carpet. The machine applies cleaning solution to the carpet and
removes dirty solution and soil from the carpet. The Image 16 is equipped with a power brush. The extractor has
controls to start the solution pump, and vacuum motor. The extractor (floor spray and brush) can be operated
intermittently or continuously. This machine is intended for commercial use.
Specifications:
Image 16i Image 16ix
120V 120V
Model 04110B 04111B
Solution Pump 100 PSI Fixed 0-100PSIVariable
PowerCable 35'3-wire 50' 3-wire disconnect
Spray Jets 4 Q.C. front, 1 Q.C. rear
SolutionTank Capacity 8Gallons 8½Gallons
RecoveryTank 7½Gallons 7½Gallons
Waterlift/CFM 140"/101
Vacuum Tangential discharge,2 HP,3 stage
Electrical 120 Volt 50/60 Hz
Brush Size 3" x 13"
Brush Motor Size 1/8HP
Dimensions 33" x 46" x 16"
Weight 101lbs.
ShippingWeight 140lbs.
DANGER: Machinescancauseanexplosionwhenoperatednearflammablematerialsandvapors. Donot
usethismachinewithornearfuels,graindust,solvents,thinners,orotherflammablematerials.
WARNING: You must have training in the operation of this machine before using it. READ THE
INSTRUCTION BOOK FIRST.
WARNING: Do not use this machine as a step or furniture. Injury could occur to the operator.
WARNING: Toavoidseriousinjury,useproperliftingprocedureswhenliftingthemachine.
WARNING: Makesurethatallthelabels,decals,warnings,cautionsandinstructionsarereadable. Replace
them when necessary by ordering them from Clarke.
WARNING: Do not use water that is hotter than 140°F.
WARNING: Improperdischargeofwastewatermaydamagetheenvironmentandbeillegal. TheUnited
States Environmental Protection Agency has established certain regulations regarding
dischargeofwastewater. Also,cityandstateregulation regarding this discharge may be in
effect in your area. Understand and follow the regulations in your area. Be aware of the
environmentalhazardsofchemicalsthatyoudispose.

EN
ENGLISH
Clarke®Operator's Manual (EN) - Image 16 I/IX 120V - 5 -
This product must be grounded. If it should malfunction or
breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This product
is equipped with a cord having an equipment-grounding
conductor and grounding plug. The plug must be inserted into
an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING: Improper connection of the
equipment-grounding conductor can result in a risk of electric
shock. Check with a qualified electrician or service person if
you are in doubt as to whether the outlet is properly grounded.
Donotmodifythe plug provided with the product - if it will not fit
theoutlet, have a proper outletinstalledbya qualified electrician.
This product is for use on a nominal 120 volt circuit and has a
grounding attachment plug that looks like the plug illustrated in
Fig. 1. Make sure that the product is connected to an outlet
having the same configuration as the plug. No adaptor should
be used with this product.
For maximum protection against electric shock, use a circuit
that is protected by a ground fault circuit interrupter. The green
(or green and yellow) conductor in the cord is the ground wire.
Never connect this wire to any terminal other than the ground
terminal.
WARNING: To prevent possible electric shock, protect
the machine from rain. Keep the machine
ina dry building.
WARNING: To prevent possible electric shock, always
use a 3-wire electrical system connected
to the electrical ground. For maximum
protection against electrical shock, use a
circuit that is protected by a ground fault
circuit interrupter. Consult your electrical
contractor.
WARNING: Do not cut, remove or break the ground pin.
If the outlet does not fit the plug, consult
your electrical contractor.
WARNING: Have worn, cut, or damagedcordsandplugs
replaced by an authorized service person.
EXTENSIONCORDS
Use only an approved extension cord with three conductors, a
plug with three terminals, and a connector body with three holes.
The machine has a power cord with wire size 14 AWG (AWG
means American Wire Gauge).
WARNING: If you use an extension cord, use an
extension cord with minimum wire size 14
120 VOLT, 50/60 CYCLE MACHINES
GROUNDING INSTRUCTIONS
Figure1
Grounded
Outlet
Grounding
Plug
Grounded
Outlet Box
GROUNDING INSTRUCTIONS

EN
ENGLISH
-6- Clarke®Operator's Manual (EN) - Image 16 I/IX 120V
THE CONTROLS
The Vacuum/Accessory Switch
This switch is located on the left side of the control
panel. To turn the vacuum motor and pump motor on, press
the bottom of the switch. To turn the vacuum motor and
pump motor off, press the top of the switch.
The Spray/Brush Motor Switch
The spray/brush switch is located in the center of the
control handle. To turn on the spray/brush intermittently,
press the top of the switch and hold for the length of time
you want the floor spray/brush to run. To turn on the spray/
brush continuously, press the bottom of the switch. To turn
the spray/brush off, press the center of the switch.
NOTE: The vacuum/accessory switch must be in the "I"
positionbefore spray will work.
The Vacuum Hose Connector
Thevacuum hose connector ison the centerright hand rear
ofthe machine.
The Solution Hose Connector
The solution hose connector is located in the center in the
rear of the machine. This connection is used to hook up
optionalauxiliary floor tools.
Recovery Tank Drain
Removehosefromrearof machine. Place over drain and
openvalve.
Rinse Tank Drain
Removethehose from the rear ofthe machine. Place over
drain.
BrushAdjustment
Adjustment is located to the front right side of the machine.
Pull spring loaded pin and place in selected slot. If breaker
trips,move adjustmentone slot higher.
Variable Pump Pressure (ix model only)
The control knob is located on the right side of the control
panel.Theknob is divided into threeoperatingranges;
upholstery,interex and restoration. Theserange settings
are only suggested starting points. The control knob can be
adjustedclockwise to increaseflow and pressureor counter
clockwiseto decrease flow andpressure. Ifstreaking
occurs, increase pressure setting.
Upholstery Setting: Used for accessory tools.
Interex Setting: Usedwithinterim brush for
light extraction at medium
flowandpressure.
Restoration Setting: Usedwithrestoration
brushfordeepextraction
athighflow and pressure.

EN
ENGLISH
Clarke®Operator's Manual (EN) - Image 16 I/IX 120V - 7 -
HOWTO PREPARE THE MACHINEFOR OPERATION
WARNING: This machine has moving parts. To reduce the
risk of injury unplug before servicing.
WARNING: To reduce the risk of fire, use only commercially
available floor cleaners and waxes intended for
machine application.
WARNING: Do not use water that is hotter than 140° F.
WARNING: Operating a machine that is not completely or
fully assembled could result in injury or property
damage. Do not operate this machine unless it
is completely assembled. Inspect the machine
carefully before operating.
This machine is intended for commercial use.
Flush rinse tank and chemical tank completely.
To prepare the machine for operation, follow this procedure:
1. Select the correct type brush for your application. Choose either
the interim or restoration brush.
NOTE: Brushes Available: 14671A-Brush, Interim Assembly,
14657A - Brush, Restoration Assembly
To change the brush type, follow these instructions:
a. Remove left brush pivot screw.
b. Remove one (1) brush retainer screw and loosen the other
retainer screw.
c. Rotate brush retainer plate to the side.
d. Grasp brush on drive end (right side) pull brush toward the
steel brush plate.
e. Pull left side of brush out of housing and slide brush
assembly from drive mechanism.
To reassemble, follow these instructions:
a. Align brush drive slots with brush drive pin.
b. Apply pulling pressure to the brush drive end (pulling toward
the steel brush plate), apply end pressure to the left end of
the brush and slide brush assembly into the brush housing.
c. Insure that the two (2) marks can be seen on the brush pivot
after brush assembly is in place.
d. Align the brush retainer and install the brush pivot screw.
e. Tighten both brush retainer screws.
2. Before moving the extractor onto the carpet, put clean hot water
into the solution tank. The solution tank capacity is approxi-
mately seven gallons.
3. For Image 16i only: Add two to ten ounces of Clarkare®Extractor
Concentrate" per every one gallon of water, depending on carpet
condition.
4. If the extractor removes an excess amount of foam from the
carpet, add a defoamer such as Clarkare®Defoamer Concen-
trate to the recovery tank. The amount needed will change
according to the amount of detergent already in the carpet.
CAUTION: Do not leave the extractor or other cleaning
machines or tools on the carpet when not in
use. Cleaning solution in the machines and
tools can leak onto the carpet and cause light
spots or stains.
NOTE: To order Clarkare®Extractor Concentrate, Order
Part No. 398421. To order Clarkare®Defoamer,
order Part No. 398420.
For instructions for preparation and operation of your floor tool, read
the operator's manual supplied with your floor tool.

EN
ENGLISH
-8- Clarke®Operator's Manual (EN) - Image 16 I/IX 120V
Figure2
Figure3
3 2 1
6 5 4
5
78
6
42
9
HOW TO CLEAN AN AREA OF CARPET
CAUTION: The recovery tank is equipped with an
electric shut-off float switch. When the
recovery tank becomes full, all electrical
functions will automatically be shut off. Turn
the vacuum/accessory and spray/brush
switch to the "OFF" position before emptying
the recovery tank.
Recomendations for best Wash-n-Rinse cleaning results
1.Vacuumcarpet thoroughlybefore cleaning.
2.Precondition spots,stains andany hightraffic areasas needed.
3.Clean carpetby followingthe instructions in this section. See
"HowtoOperate the Machine".
4.After cleaning,dry carpets by using Clarke fans. Windows
shouldbe opento assistin properdrying.
Note: When using the extractor to clean carpets, follow this
procedure:
1. Do not walk on freshly cleaned carpets for at least four hours or
untilthe carpet is dry to touch.
2.If aluminumor plasticpieces havebeen placed under the legs of
furniture,do notremove themuntil the carpet is dry.
3. Do not allow children or pets to crawl or walk around on the damp
carpet.
4.Vacuum right afterthecarpet is dryand then vacuumthe carpet
once a week, or as often as needed.
To clean an area of carpet, follow this procedure: (See figure
2)
1. Put water intorinse tankand cleaningsolution into the
chemical tank. Clarke recommends using Clarkare Extrac-
torConcentrate as a cleaning solution.
2. Turn the vacuum/accessory/switch to the "I" position.
3. To adjustbrush height,place brushadjusting rodin the
positionthat correspondsto yourcarpet type. Proper
adjustmentis with approximatley1/8" bristle engagement.
NOTE: Incorrect brush height may cause circuit breaker to
trip. Raise brush and reset circuit breaker.
4. Turn the spray/brush switch to the "I" position(or for
intermittentuse, press and hold thespray/brush switch to
the"II" position). With the switch activated, slowly and
steadilypull the machine backwards.
5. Shut the spray/brush"O" andvacuum anadditional six
inches.
6. To clean a small area of carpet, clean the carpet in sections
threefeet square. As you make additional passes,overlap
oneinch of thearea alreadycleaned.
7. To removemore liquidfrom the carpet, liftupslightly onthe
handle,transferring machine weight to thepick up head.
Thespeed youmove the machine will depend on how dirty
the carpet is. If the carpet is very dirty, move the machine
slower.
8. As the machine is used, dirty solution will begin tofill the
recoverytank. Whenthe solutiontank is empty, the recovery
tankmust beemptied. If the solution in the recovery tank is
foamy, therecovery tankmay needto beemptied beforethe
solutiontank is refilled.

EN
ENGLISH
Clarke®Operator's Manual (EN) - Image 16 I/IX 120V - 9 -
How To Clean ALarger Area Of Carpet
Seefigure3.
Tocleana larger area ofcarpet, follow thisprocedure:
1. Beginatthe right-hand cornerof the carpet.
2. Make a passhalfway along theedge ofthe carpet. Pull
the machine backward at a steady speed.
3. Moveto the edge of the carpet. Make another passnext
to your first pass.
4. As you make more passes, overlap one inch of the
area already cleaned. Make each pass four inches
differentin length toprevent making aline in thecenter
ofthe carpet.
5. Make more passes until half of the carpet is cleaned.
6. Move to the right hand corner of the carpet not yet
cleaned.
7. Make a pass halfway along the edge of the carpet.
8. As you make passes, overlap one inch of the area
alreadycleaned.
9. Make more passes until all of the room is cleaned.
CAUTION: Clarke will not be held liable for dam-
age to the carpet, or poor results because
of the operator's lack of ability.
OPERATOR'SMAINTENANCE
How to Empty the Recovery Tank
Toemptythe recovery tank,follow thisprocedure:
1. Turn all switches on the machine to the "O" position.
2. Position the machine over a drain or position a bucket
underthe drain valve spout.
3. Turnthevalve.
4. Closethedrainvalve.
CAUTION: The recovery tank is equipped with an
electric shut-off float switch. When the
recovery tank becomes full, all electri-
cal functions will automatically be shut
off. Turn the vacuum/accessory and
spray/brush switches to the off position
before emptying the recovery tank.
How to Empty the Solution Tank
1. Turn all switches on the machine to the "O" position.
2. Position the machine over a drain or position a bucket
underthe drain valve spout.
HOWTO CLEAN AN AREA OF CARPET