Clas Ohlson RE351SSC User manual

ENGLISH SVENSKA NORSK SUOMI
38-2662
External/internal Cabinet 3.5”



Model RE351SSC



2
ENGLISH
External/internal Cabinet 3.5″
Art.no. 38-2662, model RE351SSC
Please read the entire instruction manual before using and save it for future use.
We apologise for any text or photo errors and any changes of technical data.
If you have any questions concerning technical problems please contact our
Customer Service Department (see address on reverse.)
This unit contains
- External cabinet for 1x 3,5” HDD (SATA I / SATA II)
- 5.25” cabinet holder/mounting frame
- Power adaptor
- Instruction manual
- USB cable
- SATA cable
- Mounting screws
System demands
- PC with SATA port on the motherboard (for internal use).
- PC with USB port (for external use).
Helpful suggestions
- A new hard disk should be partitioned and formatted correctly before use (read
the hard disk’s instruction manual).
- Always save important data on several storage media for safety.
- Never remove the external cabinet when the hard disk is reading or writing
data, you might damage the hard disk.
- Do not expose the cabinet to heat or direct sunlight.
- Do not place the external cabinet close to strong magnetic elds such as
TVs or Hi-Fi speakers. This could erase data or cause the hard disk to stop
working.
- Always handle the hard disk carefully; do not expose it to impact or vibrations.
- Note! The computer needs a functioning USB 2.0 port to take advantage of the
higher data transfer rate, USB 1.1 ports only provide the lower data transfer
rate (applies for external use).

3
ENGLISH
Assembly
Removing the external cabinet from the holder
1. Pressthecatchonthedoor
labelled“PUSH”(nexttothe
arrowonthepicture).
2. Carefullyreleasethecatch
untilitreachesthestop.
3. Removethecabinetbypulling
itstraightout.


ENGLISH
Inserting the external cabinet into the holder
1. Pressthecatchonthedoorla-
belled“PUSH”(nexttothearrow
onthepicture)andopenituntilit
reachesthestop.
2. Carefullyslidethecabinetallthe
wayintotheholder.
3. Makesurethatthecatch
latchesontheholder(see
thepicture).
4. Pushthecabinetinuntila
clickisheard.Thecabinetis
nowmountedintheholder.

5
ENGLISH
Mounting in a vacant 5.25″ rack in the computer
1. Pressthecatchonthedoorlabelled
“PUSH”(nexttothearrowonthe
picture).Pulltheharddiskcabinet
outoftheholderinthedirectionof
thearrow.
2. Unscrewthebackofthecabinet
andpullouttherearpanel.

6
ENGLISH
3. Mounttheharddisk(SATA)
asshowninthepicture.
Makesurethatthehard
diskisproperlyconnected
totheSATAport.
Note. Ifanewharddiskisbeingused,itmustbeformattedbeforeuse.
4. Mounttheharddiskusingthe
screwssupplied.
5. Mountthespringsasinthe
picturetoo.Note!Donot
tightenthescrewsholding
thespringstoomuch.Allow
enoughplayforthespringsto
move.
6. Replacetheharddiskinthecabinetandtightenthescrews.


ENGLISH
7. Carefullyslidethecabinetallthewayintotheholderandclosethedoor
(read”Insertingtheexternalcabinet”).
8. Turnoffandopenyourcomputer.
Mounttheholder/mountingframein
thedesiredvacant5.25″rackinthe
computerusingthescrewssupplied.
9. ConnectthepoweradaptortothepowerinputandtheSATAcabletothe
SATAport.
10.ConnecttheotherendoftheSATAcabletoafreeSATAportonthemother-
board.

8
ENGLISH
Use
Using the external cabinet via a USB port.
The following instructions apply for Windows XP with Service pack 2 installed.
1. ConnectthepoweradaptertotheportmarkedDC12Vonthebackofthe
cabinetandtoavacantwallsocket.
2. ConnectthesuppliedUSBcablebetweenthecabinet’sUSBportandavacant
USB2.0portonthecomputer.
3. Thecomputerwilllocatetheexternalcabinetautomatically;noextradrive
routinesareneeded.
4. Thenewdevicewillappearin“Mycomputer”under“harddisks”(remember
thattheharddiskmustbepartitionedandformattedbeforeuse,otherwiseit
willnotappearin“Mycomputer”.Readtheharddisk’sinstructionmanual.
Removing the external cabinet
If you wish to remove the external cabinet without turning off your computer, click
on the icon in the activity window and select which device is to removed and click
on “Ok”. Then you can pull out the USB cable and the adaptor.
Care and Maintenance
Use a soft damp cloth to wipe the product. Never use strong detergents. Always
turn the power off before cleaning.
Troubleshooting Guide
Problem: Thecomputercannotlocatetheharddisk.
Solution: 1.Checkthattheharddiskhasapartitionthatisformatted.
 2.MakesurethattheUSBcableisproperlyconnectedtothe 
 computerandtheexternalcabinet.
 3.MakesurethattheUSBportissupplyingtheexternalcabinet
 withpower(tryanother USB product in the port).


ENGLISH
Disposal
Follow local ordinances when disposing of this product. If you are unsure about
how to dispose of this product contact your municipality.
Specications
Harddisk 2x3.5”SATAI/II(notincluded).Upto1,000GB
Powersupply(cabinet) 5/12VDC,2Aviaapoweradaptor230VAC
Powersupply(holder) 5/12VDC,2A
Interface SATAI/II,USB2.0
Operatingsystem SupportsWindowsVista,XP,2000,ME
USBdatatransferrate Upto480Mbs(USB2.0)
Cooling Passivecooling(nobuilt-infan)
Holderport SATAI/II
ExternalCabinetports Externalports:USB,SATAI/II
 Internal3.5”HDDSATAI/IIport
Size(holder) 150x215x40(WxHxD)
Size(cabinet) 115x200x32(WxHxD)

10
SVENSKA
10
Externt/Internt kabinett 3,5”
Art.nr 38-2662, modell RE351SSC
Läs igenom hela bruksanvisningen före användning och spara den sedan
för framtida bruk. Vi reserverar oss för ev. text- och bildfel samt ändringar
av tekniska data. Vid tekniska problem eller andra frågor, kontakta vår kundtjänst
(se adressuppgifter på baksidan).
Förpackningen innehåller
- Externt kabinett för 1 st. 3,5” HDD (SATA I / SATA II)
- 5,25” hållare/monteringsram för kabinett
- Spänningsadapter
- Bruksanvisning
- Usb-kabel
- SATA-kabel
- Monteringsskruvar
Systemkrav
- Pc med SATA-anslutning på moderkortet (för intern användning).
- Pc med usb-anslutning (för extern användning).
Tänk på detta
- En ny hårddisk måste alltid partitioneras och formateras innan den kan
användas (se hårddiskens bruksanvisning).
- Spara alltid viktiga data på era olika lagringsmedia, för säkerhetsskull.
- Ta inte bort det externa kabinettet när hårddisken håller på att läsa eller skriva
data, hårddisken kan ta skada.
- Placera inte kabinettet så att det utsätts för hetta eller direkt solljus.
- Placera inte det externa kabinettet i närheten av starka magnetfält, t.ex. tv-
apparat, stora högtalare etc. Det kan radera data eller leda till att hårddisken
inte fungerar.
- Hantera alltid hårddisken försiktigt, den tål inte att utsättas för stötar eller
vibrationer.
- Obs! Datorn måste ha en fungerande usb 2.0 –port för att utnyttja den
högre överföringshastigheten, usb 1.1 –portar ger endast den lägre
överföringshastigheten (gäller vid extern användning).