Classic Exhibits SEGUE DESIGNS VK-1964 Manual

© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-1964 General Layout
Plan View
10’
10’
Scale: 15

© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2017
www.classicexhibits.com
Order #XXXXX
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
4
13
2
Fold edges over.
Insert into
groove
of frame
General Information

© 2017
www.classicexhibits.com
Order #XXXXX General Information
CEI-110 Profile
Straight Connection
Corner Connection
TS RV 4
Bracket
Insert Bracket
into the Interior
Center Slot
of extrusion.
Slide connecting
extrusion over
exposed end
of bracket.
Secure extrusion
using remaining
set screws.
Set
Screw
CEI-110 Frames Assembly
Disassembly
1) Loosen set screws on brackets, then slide
extrusions off of brackets.
Straight Bracket Installation (when required)
1) Slide TWO-PIECE TS RV 4 straight bracket into
Interior Center Slot of extrusion so that two of the
set screws are inside groove.
Tighten two set screws to secure.
2) Slide connecting extrusion over exposed end
of bracket. Tighten two remaining set screws
to secure.
Corner Bracket Installation
1) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of extrusion so that two
set screws are inside groove.
Tighten two set screws to secure.
2) Slide one A1 L-Bracket into outer interior
grooves of upper and lower horizontals.
Tighten set screws to secure.
3) Slide vertical extrusion over exposed ends
of brackets in lower horizontal.
Tighten set screws to secure.
4) Slide exposed ends of installed brackets of
upper horizontal into open ends of verticals.
Tighten set screws to secure.
TS RV 2
Upper
Horizontal
Lower
Horizontal
Upper
Horizontal
Lower
Horizontal
TS RV 2
8 Brackets Total:
(4) - TS RV 4
(4) - A1 L-Brackets
A1
A1
Slide verticals over
brackets of lower
horizontal, then slide
upper horizontal &
brackets into grooves
& center slots
of verticals.
Completed
Assembly
Insert L-Brackets into the
Interior Center Slot & outer
interior grooves of extrusion.
Completed
Assembly
Secure inserted half
of bracket, using
set screws.

© 2017
www.classicexhibits.com Case 1 of 3
Order #XXXXX Case Packing
Graphics
Setup Hardware
Top View of Each Level
Level 1
Wings
4 5 4A 5A 3A,3 8 8A 2,2A
Level 2 Level 3

© 2017
www.classicexhibits.com Case 2 of 3
Order #XXXXX Case Packing
Litureature Holders
Top View of Each Level
Level 1
7A
10A 10/11
Counter Top
Base
Plates
6A 6 7
Canopy
Pieces
Level 2 Level 3

© 2017
www.classicexhibits.com Case 3 of 3
Order #XXXXX Case Packing
Top View of Each Level
Level 1 Level 2 Level 3 Level 4
Infill
Side
Panel
Assembly
Shelf
Counter Top
Level 5
Side
Panel
Assembly
Door
7, 7A

© 2017
www.classicexhibits.com Step 1 of 5
Order #XXXXX Backwall Assembly
4
1
5
8
8A
1
4A
5A
3
3A
6A
7A
2
2A
6
7
Power
Break
Completed Backwall Assembly
Power
Break
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
Item
1
2/2A
3/3A
4/4A
5/5A
6/6A
7/7A
8/8A
Qty.
2
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Description
Base Plate
42”w S40 Vertical Extrusion
42”h S40 Vertical Extrusion
42”h CEI110 Horizontal Extrusion
42”h CEI110 Horizontal Extrusion
42“h CEI110 Vertical Extrusion
42“h CEI110 Vertical Extrusion
40.1767“h Z45 Vertical Extrusion
Steps:
1) Attach Base Plates [1] to Vertical [2] & [3], using bolts.
3) Assemble CEI-110 Extrusions together, with Verticals [8,8A] between.
See General Information page CEI-110 Frames Assembly for details.
4) Connect Verticals [2,2A] and [3,3A] together then attach to each side
of assembled CEI-110 frame. See CEI-110 to S40 Connection detail.
5) Connect lighting power cords and attach transformers.
See Light to Light Connections & Light to Transformer details.
6) Apply SEG graphic and blocker to front & back of assembled frame.
See SEG Graphic Installation detail.
V4 Connector
CEI-110
S40
Slide V4 Connector into groove of S40. Tighten
set screw to secure V4 Connectorin place at
correct elevation. Insert Screw Cap stud through
hole of CEI-110 into threaded hole of V4 connector.
Tighten Screw Cap to secure in place.
CEI-110 to S40 Connection
Screw Cap
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
Light to Light Attachment
Light to Tranformer Attachment

© 2017
www.classicexhibits.com Step 2 of 5
Order #XXXXX Canopy Assembly
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Steps:
1) Connect canopy pieces together as shown.
2) Apply pillow case graphic to assembled canopy.
AA
BB
D
D
CC
Push-Button
Push button then rotate
for packing purposes
E
F
E
FG
H
G
H

© 2017
www.classicexhibits.com Step 3 of 5
Order #XXXXX Backwall Attachments
Completed Assembly
10
10A
2
Canopy
11
Screw
Note: Curved Extrusion
[10] and Horizontal [11]
stay assembled for
shipping and packing.
*
Item
10
10A
11
11A
Description
30.2” Curved Extrusion
Support Leg
12.184”w Horizontal Extrusion
Flange Plate
Qty.
1
1
1
1
Steps:
1) Connect assembled Extrusions [10/11] and Shelf to Vertical [2].
2) Connect Support Leg [10A] to Curved Extrusion [10].
3) Attach Flange Plates [11A] to tops of Curved Extrusions [10], using screws.
4) Attach Counter Tops to [11,11A]. See Counter Top Attachment detail.
5) Attach Wings to A10 clamps. See Wing Attachment detail.
6) Place Canopy on posts at top of assembled frame.
Counter Top Attachment
*Insert Screws, located on underside
of Counter Top, into holes on Flange
Plate then secure with Wing Nuts.
Wing Nut
Fixed
Screws
Flange
Plate
10
11
Counter Top
Slide A10 clamp into
groove of Extrusion.
When desired location
is found, tighten
Set Screw to secure.
Set
Screw
A10
Tighten Black Plastic
Set Screw to secure
Wing in place.
Wing Attachment
Keep A10 clamps
attached to Verticals
Black
Plastic
Set Screw
Shelf
11A