Classic Exhibits visionary DESIGNS MOD-1534 Manual

© 2023
Order #XXXXX
Top View
MOD-1534 Monitor Stand
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Case 1 of 1
Order #XXXXX
Top View of Each Level
Level 1 (Lower Level) Level 2 Level 3 Level 4 Level 5
Infills
Shelf
3A 4A
Counter Top
6,6
6A,6A
Side
Assembled
Door Side
Assembled
Setup Hardware
Monitor
Mount
Shelf Supports
Case Packing

© 2023
Step 1 of 2
Order #XXXXX
BACK VIEW
Item
1
2
3
3A
4
4A
5,5A
6,6A
Qty.
1
1
1
1
1
1
2,2
2,2
Description
37.5” Vertical Extrusion
37.5” Vertical Extrusion
37.875” Vertical Extrusion
22.125” Vertical Extrusion
37.875” Vertical Extrusion
22.125” Vertical Extrusion
16.378” Horizontal Extrusion
16.378” Horizontal Extrusion
Steps:
1) Attach verticals [4] to [4A] and [3] to [3A], using connectors. See
Connector detail.
2) Attach horizontals [5] and [6] between verticals [1] [2] [3] [3/3A] and [4/4A].
3) Slide infills between verticals [1 & 2] [1 & 4] and [2 & 3], then secure with
horizontals [5A] and [6A] on top.
4) Attach assembled door to vertical [4]. See Door Attachment detail.
6A
5A 6A
5A
Infill
Infill
Infill
Door
12
3
3A
6
5
6
4
4A
5
Door
Hinge
Hinge
Pin
Slide Pin into
Hinge attached
to Vertical.
Slide Door
Hinge over Pin.
Door Attachment
*
*
*
*
Partial
Completed Assembly
Monitor Stand Assembly

© 2023
Step 2 of 2
Order #XXXXX
Steps:
1) Attach shelf supports to interior side of infills,
using Velcro, then place internal shelf on top.
2) Set counter top onto assembled base.
See Counter Top Attachment detail.
3) Install monitor mount to verticals [3A] & [4A].
See Monitor Mount Attachment detail.
Counter Top
Internal Shelf
Shelf Support
Shelf Support
Shelf Support
Shelf Support
4A
3A
**
*
*
Completed Asssembly
Monitor Mount
Attachment
Slide connectors into
grooves of verticals.
Tighten set screws.
Attach back plate
to connectors, using bolts.
Connectors
Back
Plate
*
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
Monitor Stand Assembly (cont’d)