Classic Exhibits visionary DESIGNS MOD-1229 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Item
17
18
19
20
21
22
23
24/24A
25
25A
--
Description
37.5”h Q914 Vertical Extrusion
37.5”h Q914 Vertical Extrusion
37.5”h Q914 Vertical Extrusion w/Door Hinges
37.5”h Q914 Vertical Extrusion w/Door Stop
32.5”h Q914 Vertical Extrusion
32.5”h Q914 Vertical Extrusion
13.5”w Z45 Horizontal Extrusion
14.5”w Z45 Horizontal Extrusion
5.75”w Z45 Horizontal Extrusion
7”w Z45 Horizontal Extrusion
PR63 Conduit
Qty.
1
1
1
1
1
1
5
2/2
2
2
1
Steps:
1) Attach upper Vertical Extrusions [21,22] to lower Vertical Extrusions [19,20].
2) Attach Horizontal Extrusions [23,24 and 24A] between Vertical Extrusions,
placing Infills and attaching Door where indicated.
3) Attach Shelf Supports to inside of assembled base using Velcro,
then set Internal Shelf on top of supports.
4) Attach [25,25A] to Verticals [17,18,19,20], then attach Shelves
to Velcro on top of [25,25A].
5) Place Counter Top on assembled base and secure with pins.
See Counter Top Attachment detail.
6) Attach Monitor Mount to assembled workstation where indicated.
See Monitor Mount Attachment detail.
7) Run cords through grommet in counter top & attach PR63 to
vertical [22] as shown for wire management. See PR63 Attachment detail.
25A
25A
25
25
17
18
21
22
23
24A
Door
Top
Insert
Infill
Infill
Infill
23
23
23
23
24
19
20
24
Completed Assembly
Shelf
Shelf
PR63
24A
Velcro
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
**
Internal
Shelf
STEP 1
STEP 2
Slide Connectors into groove of
extrusion. Tighten Set Screws to
secure.
Attach Monitor Plate to Connectors,
using supplied bolts.
Connectors Connectors
Monitor Mount Attachment
*
Monitor
Plate
Screws
*
*
Internal
Shelf
Supports
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
pinch
PR63 Attachment
1) Run cords through
PR63 plastic conduit.
2) Attach conduit where
indicated by pinching
the opening and
inserting into the
groove of extrusion.
PR63 conduit
*
**
Grommet
Counter Top
MOD-1229 Monitor Stand
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Case 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Infills
17 18 19 20
Door
25A
25A
23
(qty. 5)
24,24,24A,24A
25
25
Setup Hardware
Level 1
(Bottom level)
Level 2 Level 3
Case Packing

© 2023
Case 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4
Monitor
Mount
InfillsShelf
Wing Shelf
Wing Shelf
Counter
Top
Shelf Supports
Shelf Supports
Case Packing