Classic Exhibits eco-systems ECO-104T Manual

© 2022
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
ECO-104T Table Top Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2022
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2022
Order #XXXXX
TSP46 Profile
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Corner
Connector Corner
Connector
Corner
Connector
Corner
Connector
COMPLETED ASSEMBLY
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
Straight Connection
3) Tighten all knobs to secure connection.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
Slide connector across seam of extrusions.
Tighten all knobs.
All knobs must be tightened securely to ensure a proper connection.
Straight Connector
2) Loosen all knobs, then slide straight
connector across the seam of extrusions.
TSP46 Frame Assembly

© 2022
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2022
Case 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each Level
Graphics
2 3 4
1,1
Header
Aero Frame
5
6 7 8 9
Level 1
(Bottom level)
Level 2 Level 3
Setup Hardware
Lights
Case Packing

© 2022
Step 1 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Item
1
2
3
4
5
6
7
8
9
Qty.
2
1
1
1
1
1
1
1
1
Description
8” x 22” Base Plate
46”h S44 Vertical Extrusion
46”h S44 Vertical Extrusion w/ key holes
46”h TSP46 Vertical Extrusion
46”h TSP46 Vertical Extrusion
30”w TSP46 Horizontal Extrusion
30”w TSP46 Horizontal Extrusion
30”w TSP46 Horizontal Extrusion
30”w TSP46 Horizontal Extrusion
Steps:
Refer to the TSP46 Frame Assembly general information page.
1) Attach Base Plates [1] to bottom of verticals [2,3], using bolts.
2) Assemble horizontals [6-7], [8-9] together using straight connectors,
3) Attach verticals [4,5] between horizontal assemblies [6/7], [8/9]
using corner connectors.
4) Connect verticals [4,5] to verticals [2,3] using custom cam locks.
See Custom Cam Lock detail.
FRONT VIEW
Custom Cam Lock
*
Attach cam lock
to groove of
vertical extrusion.
Tighten set screw
to secure connection.
2
3
4
5
6
7
8
9
1
1
Key Hole
Key Hole
*
*
*
*
Backwall Assembly

© 2022
Step 2 of 3
Order #XXXXX
Using Your Setup Instructions
The Aero Setup Instructions are created specifically for your configuration. The instructions include an
exploded view of the frame which is sequentially labeled. We encourage you to review the instructions
before attempting to assemble your exhibit.
Connections are kept very simple; no tools required. Everything assembles with push-button connectors.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Push-Button
Push-Button
66
6
6
Numbered Label
Connections are made by holding the button down and
sliding the red tube into opposing tube until button locks
into the hole of the opposing tube. To disassemble, push button
and pull or twist extrusions apart.
Locked layer contains
placeholder marks.
1
2
3
4
5
6
78
9
11 12
10
Steps:
1) Connect in numberical order as shown.
2) Apply pillow case graphic.
When assembled
Aero Frame Assembly

© 2022
Step 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Light
Light
Header Graphic
Completed Assembly
Steps:
Refer to the SEG Installation general information page.
1) Apply SEG graphic to front of frame assembly.
2) Connect Aero Frame to key holes on vertical [3].
3) Attach Header Graphic to top horizontals using A10 clamps.
See Header Attachment detail.
4) Connect Lights to top horizontals.
See Light Attachment detail.
1) Slide A10 connector
into groove of extrusion.
2) Tighten set screw to
secure A10 to extrusion.
3) Insert Header into
Clamp.
4) Tighten knob to secure
wing in place.
Header Attachment
*
1
2
3
4
Light Attachment
Attach lights to
Horizontal where
desired and
tighten in place.
*
*
*
*
*
*Keyhole Attachment
Insert bolts of Aero frame into keyhole
slot in groove of vertical extrusion,
slide Aero frame down to secure.
*
*
S
E
G
Gr
ap
h
ic
Attachments