Clearlite Bathrooms Alcove User manual

Please read these Instrucons carefully
May 2018
Installaon Instrucons
Alcove

C
B
Components
A - Door Assembly
B - Door Wall Receiver
C- Cover Trim x 2 (On Selected Models)
(For shipping purposes the Door & Return
Receivers are packed in the sides of the Door and Return
Installaon Components
Handle
(where applicable)
Drip Seal –1m
Cleaning Towelee
(White showers only)
No.6 x
10mm screw
No.6 x 38mm screw
Qty 6
Screw Cap
Qty 6
 Drill
 Spirit level
 Tape Measure
 Screw Driver (No.1 Sq drive)
Tools Required
 Caulking Gun
 Masking tape
 Pencil
 Cleaning Cloth
Tube of NG Silicone
(Colour matched to
shower)
A
C
B
9mm Plug
Qty 3

Installaon
Note:
Your shower Door can be installed to open from the le or right hand
side by rotang the door 180 degrees, and the Return Panel can be
fied on either side. You must decide which way the door is to open be-
fore starng the installaon.
3) Pre drill three equally spaced clearance
holes (i.e. top, boom and centre) in
the Door Wall Receiver using a 4.5mm
drill bit. Reposion the Wall Receiver
to the pencil line on the wall. Drill into
the wall through the clearance holes
using the 3.0mm drill bit. N.B. The
holes preferably locate into a stud or
nog. As an alternave, a toggle system
can also be used.
4) Secure the Wall Receiver to the wall using the
No.6 x 38mm stainless steel screws
NB As a precauon apply silicone sealant into the
drilled holes
1) Determine which side the Door is
to be hung. Posion one of the
Door Wall Receivers hard against
the inside edge of the tray up-
stand.
NOTE: If the shower walls
are to be tiled the Wall Re-
ceivers must be installed to
the Water proof membrane
before tiling. This ensures
the doors will fit within the
lip of the tray
2) Plumb up the Door Wall
Receiver using a spirit
level. Mark the posion
with a pencil line.
Wall Receivers
5) Fit the handle to the door (where required).
This will assist in the opening & closing during
the installaon process
Ensure to fit the plasc washers and bush to
prevent metal on glass contact

7) Ensure the Door is facing the correct way with the door opening outwards. Do not remove the door
seng block, this will assist in supporng the door during installaon and seng the correct clear-
ance from the sill.
Li the Door assembly with the Wall Receiver aached onto the shower step and slide into the
Door Wall Receiver already installed
6) Side the remaining Door Wall Receiver onto the Door Assembly.
Door

8) Plumb the Door and remaining Wall Receiver. Through the oversize holes in the Door jamb
drill through the Wall Receiver frame and into the wall stud using a 3.0 mm drill bit
9) Secure the Wall Receiver to the wall using
the No.6x 38mm stainless steel screws.
10) Cap the oversize holes in the door Jamb using the
9mm plasc plugs
13) From the inside using a 3.0mm drill bit; drill through the vercal secons of the Door into the Wall
Receivers. Fix the Door to the Wall Receivers. You must have a minimum of 10mm overlay and the
holes must be drilled no less than 5mm from the edge of the vercal aluminium secons. Secure in
place using the 6 gauge x 10mm screws.
Secure the Door Set (All Screw fixings are made from the Inside)

15) Cover all Screw heads with the Screw Caps
16) Slide the outside Clamp Block Covers off the Pivot Clamp. Using a flat blade screwdriver sufficiently loos-
en the two screws, adjust the door by sliding le or right in the pivot
Once the door adjustment is complete ensure the screws are reghtened and reinstall the Clamp Block
Covers. Open the door and remove the door seng block
Notch under Door Magnet profile
18) Fit the Drip Seals to the
glass door
14) Secure in place using the 6 gauge x 10mm
screws.
Adjust the Door
Drip Seals
17) The Drip seal is supplied in a 1m length, this will need to be
cut to the desired lengths for each side of the pivot . The open-
ing side Drip seal will also need to be notched to fit under the
door magnet profile. Make the Notch 13mm in length and fin-
ishing down to the horizontal ledge of the drip seal
NOTE: The flexible vercal blade will face towards the inside
of the shower

Sealing the Shower
IMPORTANT: DO NOT apply sealant to the inside of the shower
17) For White Showers only - take the Cleaning
Towelee and wipe the surfaces of the
Powder coated profiles where Silicone will
be applied Allow to dry (1-2 minutes)
18) The Door can now be sealed in place using
silicone sealant. Ensure all surfaces are first
cleaned with dry clean cloth. Seal between
the tray upstand and the door set along the
boom outside edges. Seal vercally be-
tween the Wall Receivers and Wall Liner
Note MASKING the area to be Sealed will result
in a superior finish
19) Cover Trim– (selected models only)
The Cover Trim is provided to cover the exposed vercal edge of
the wall liner and is the final step of the installaon. For some
installaons the Cover trims may require cung to length
To fit the Cover trim apply small vercal beads of silicone down
the Wall Receiver and the exposed wall lining outside of the Wall
Receiver. Embed the Cover trim into the silicone. If the liner ex-
tends more than 10mm it will need to be trimmed prior to fing
the Cover Trim
22) Your Shower is now complete. Allow
the Sealants to cure for a minimum of
24 hours