Cleco F4-PT-RT-B User manual

For additional product information visit our website at http://www.ClecoTools.com
Instruction Manual
PL30-F4-PT
2018-04
F4-PT-RT-B
Riveter / Hammer

2
PL30-F4-PT
2018-04
Copyright © Apex Tool Group, 2018
No part of this document may be reproduced in any way or in any form, in whole or in part, or in a natural or
machine-readable language, or transmitted on electronic, mechanical, optical, or other media, without the
express permission of the Apex Tool Group.
Disclaimer
Apex Tool Group reserves the right to modify, supplement, or improve this document or the product without
prior notice.
Trademark
Cleco is a trademark of the Apex Tool Group Division.
Manufacturer
Apex Tool Group, LLC
670 Industrial Drive
Lexington, South Carolina 29072
USA
Importer
Apex Tool Group GmbH
Industriestraße 1
73463 Westhausen
Germany

3
PL30-F4-PT
2018-04
Notes on this Hardware-Description
The original language of this description is English.
This description is intended for all persons who will operate
and maintain this equipment.
Safety
General requirements
Keep this document in a safe place for future use!
These safety instructions must be accessible to the
operator at all times. They must be shown and made
available to all people involved in the use of the tool.
The operator must understand the Safety Instructions
and the Installation, Operation, and Adjustment proce-
dures provided in the Instruction Manual. These Safety
Instructions are not intended to be all inclusive. Study
and comply with all applicable Federal, State and Local
Regulations. Contact your local distributor for assis-
tance. Apex Tool Group, LLC is not the manufacturer or
supplier of the cutting tools used with this product.
Comply with all safety instructions provided by the
manufacturer of the cutting tools.
Always disconnect the tool from the air hose before
adjusting or repairing.
Immediately shut off the tool in the case of unusual
sound or vibration. Disconnect the tool from the air
hose. Have a qualified person check the tool and repair
before using.
When unpacking this tool, closely check for shipping
damages and accuracy of the shipping documentation.
Do not modify the tool, any guard or accessory unless
approved in writing by Apex Tool Group, LLC.
Implement and follow a comprehensive Safety Mainte-
nance Program to provide inspection and maintenance
of all phases of tool operation and air supply equip-
ment.
Do not operate any percussion tool unless the chisel,
scaling tool, rivet set or other implement is in the tool
and in contact with the work piece or work surface. Fail-
ure to do so can cause damage to the tool and/or seri-
ous injury.
Noise and Vibration
Refer to CE-1017TD for noise and vibration test results.
Intended use
This percussion tool is to be used for removing material
with appropriate cutting devices. Do not modify this tool. All
safety devices must be properly assembled and in working
condition.
If there is any doubt regarding the safe operation of this
product, consult Apex Tool Group, LLC before using.
Only use the product under the following conditions:
• under the prescribed environmental conditions
• with the permissible air pressure
• using clean air
Do not use the tool…
• as a hammer
• in hazardous area. When operating a percussion tool in
an explosive or flammable environment, use only non-
sparking cutting tools (example: made of beryllium cop-
per).
• higher than rated air pressure
Operator training
Main criteria for target group selection is the fact, whether
the operator, based on his level of training and knowledge,
is able to recognize possible risks and avoid hazards which
can occur during production use and maintenance of
machinery.
Personal protective equipment (PPE)
Risk of injury by being wound up in and caught by machin-
ery
Do not wear loose clothing, jewelry or rings. Injury may
result from being caught in tools.
Avoid direct skin contact with lubricants, grease or
adhesives.
Eye protection must be worn all times during the
operation or maintenance of this tool.
Ear protection must be worn all times during the
operation or maintenance of this tool.
Wear gloves when required.

4
PL30-F4-PT
2018-04
Warnings and notes
Warning notes are identified by a signal word and a picto-
gram:
• The signal word describes the severity and the proba-
bility of the impending danger.
• The pictogram describes the type of danger.
Symbols on the product
Be sure that you understand their meaning before opera-
tion
Product Description
Technical Data
Ambient conditions Air Line
CAUTION! A symbol combined with the word CAU-
TION indicates a hazard with a low level of
risk which, if not avoided, could result in
minor or moderate injuries or environmental
damage.
WARNING! A symbol combined with the word WARN-
ING indicates a hazard with a medium
level of risk which, if not avoided, could
result in death or serious injury.
DANGER! A symbol combined with the word DAN-
GER indicates a hazard with a high level of
risk which, if not avoided, will result in death
or serious injury.
This sign warns of a possibly damaging sit-
uation.
Failure to observe this note may cause the
product or parts thereof to be damaged.
General notes
include application tips and useful informa-
tion but no hazard warnings.
CE compliant
The product corresponds to the prescribed
technical requirements in Europe.
Read all instructions.
ATTENTION!
Hose connector for compressed air
Rivet tooling beehive retainer
On button
Power control
Model no. Length Weight Piston Stroke Blows
per minute
Throttle Handle Bore For use with Rivet Set
Shank Diameter
Air Inlet
(NPT)
In. mm lbs. kg In. mm In. mm In. mm
F4-PT-RT-B 8.8 223 3.3 1.5 4 102 1,700 Lever .56 14 .401 10.2 1/4“
Ambient temperature -13 °F to +104 °F (-25 °C to +40 °C)
Humidity 0 to 80 % (at +40 °C), not with dew
Working height up to 3000 m above sea level
Parameter Description
Air Hose Minimum inside diameter of 1/4" (6,35 mm)
Maximum length 8.0' (2,4 m)
Working
pressure Performance rated at: 90 psi (620 kPa)
Com-
pressed air
Air quality according to ISO 8573-1, quality class
2.4.3. The compressed air must be clean and dry.

5
P2374BA-EN
2018-04
Operating Instructions
The Cleco Production Tools "F" series riveters are
designed to operate on 90 psi air pressure using a 1/4" I.D.
hose up to 8' in length.
Air Line Lubrication
INSTALLATION AND OPERATION
Only qualified and trained personnel should install, adjust
or use this equipment.
Connect the tool to an airline with a maximum pressure
of 6.2 bar (90 psi).
Adjust the airline lubrication to a minimum to reduce
possible contamination of the environment by the
exhaust air. The work area must be well ventilated.
Inspect the air hose and fittings thoroughly.
Do not use damaged, frayed or deteriorated hoses. A
hose rupture can cause serious injury.
Keep the tool clean and dry to provide the best possible
grip. The tool should be held in such a way to be safe
and comfortable.
Do not lay the tool down until the cutting device has
stopped. Stop the tool before moving to a different loca-
tion.
Service Instructions
SPEED CHECK
Check the tool speed regularly with a tachometer to
assure it does not exceed the rated speed marked on
the tool at 6.2 bar. Check with every 20 hours of use or
weekly. Remove the abrasive before checking.
Carefully observe the maximum speed recommended
for the cutting device. This speed must be greater than
the rated speed of the tool.
CUTTING DEVICE INSPECTION
Inspect the cutting device before using. Make sure
there are no chips, cracks or other visual damage.
PROPER MOUNTING
Disconnect the air supply from the tool before mounting
or changing the cutting device.
Consult and comply with the mounting safety instruc-
tions of the cutting device manufacturer.
GUARDS
Always use prescribed guards, properly mounted for
the cutting device being used. If the guard has been
damaged, it must be discarded and replaced. Do not
alter the guard in any manner.
MAINTENANCE, ASSEMBLY & DISASSEMBLY
Inspect this equipment every 500 operating hours or
every six months, whichever comes first.
Replace worn parts using only appropriate brand
replacements parts manufactured by Apex Tool Group,
LLC.
Chisel or rivet set retainers are recommended and fur-
nished as standard equipment. Periodically inspect the
retainer for wear or damage. Damaged retainers can
allow the cutting device to eject from the tool.
RIVET SET INSTALLATION & REMOVAL
CAUTION! Shock by reaction of impact
Firmly grasp the handle before starting.
Be prepared for high short-term impacts.
CAUTION! Moving parts, throw out of parts
Disconnect air supply before installing
or replacing chisel / rivet bit.
CAUTION!
The handle should be checked after the
first eight hours of operation and occasion-
ally thereafter to make sure it is tight.
Part No. Packaged Designation
540397 1 Quar (0,94 liter) Airlube 10W/NR-420LB DR
533485 1 US Gallon (3,78 liter)
WARNING! Turn off the air and drain the air hose before
installing or removing any chisel or imple-
ment. Follow the procedure below for
installing any chisel or implement. Reverse
the procedure for removal.
Pushing on tab in a
counterclockwise direction,
unscrew the retainer off the
barrel.
Retainer
Cylinder
Insert into barrel
Rivet Set

6
PL30-F4-PT
2018-04
Riveter
Chisel Installation Procedure:
1. Remove retainer spring (#21)
2. Install chisel into bushing (#18) inside cylinder
3. Thread retainer spring (#21) onto bushing (#18)
4. For chisel removal, repeat step 1.

7
PL30-F4-PT
2018-04
Index Order no Quantity 1)
1) Included in Repair Kit
* Parts also included in (K5) 301140 O-Ring/Spring Repair
Kit
Description
1 --- 1 K1 Handle (includes Ref. 2)
2 --- 1 K1 Throttle Valve Bushing
3 --- 1 K1 Inlet Bushing (NPT)
4 --- 2 K1 Hex Socket Head Cap Screw (M5 x 8)
* 5 --- 1 K3 Throttle Valve O-Ring (S-6)
6 --- 1 K3 Throttle Valve
* 7 --- 1 K3 Throttle Valve Spring
* 8 --- 1 K3 Control Valve O-Ring (S-8)
9 --- 1 K3 Control Valve
10 --- 1 K2 Lever
11 --- 1 K2 Spring Pin (3 x 22)
12 --- 1 K2 Spring Pin (3 x 16)
13 --- 1 K4 Valve Box
14 --- 1 K4 Valve
15 --- 1 K4 Valve Knock Pin
16 --- 1 K4 Valve Seat
17 207195 1 Piston
18 207194 1 Cylinder
19 --- 1 K5 O-Ring (JASO-2035)
20 207196 1 Exhaust Band
21 207197 1 Spring Retainer
Repair Kits
K1 301136 1 Handle Assembly Kit
K2 301137 1 Trigger Assembly Kit
K3 301138 1 Control Valve Assembly Kit
K4 301139 1 Valve Assembly Kit
K5 301140 1 O-Ring / Spring Kit

Please note that all locations may not service all products.
Contact the nearest Cleco®Sales & Service Center for the appropriate facility to handle your service
requirements.
POWER TOOLS SALES & SERVICE CENTERS
Apex Tool Group, LLC
Phone: [phone]
Phone: [phone]
Fax: [phone]
www.ClecoTools.com
www.ClecoTools.de
EUROPE | MIDDLE EAST | AFRICA
Hungary
Apex Tool Group
Hungária Kft.
Platánfa u. 2
9027 Györ
Hungary
Phone: [phone]
Fax: [phone]
NORTH AMERICA | SOUTH AMERICA
Lexington, South Carolina
Apex Tool Group
670 Industrial Drive
Lexington, SC 29072
Phone: [phone]
Phone: [phone]
Fax: [phone]
Canada
Apex Tool Canada, Ltd.
7631 Bath Road
Mississauga, Ontario L4T 3T1
Canada
Phone: [phone]
Fax: [phone]
Mexico
Apex Tool Group
Vialidad El Pueblito #103
Parque Industrial Querétaro
Querétaro, QRO 76220
Mexico
Phone: [phone]
Fax: [phone]
Brazil
Apex Tool Group
Av. Liberdade, 4055
Zona Industrial Iporanga
Sorocaba, São Paulo
CEP# 18087-170
Brazil
Phone: [phone]
Fax: [phone]
Detroit, Michigan
Apex Tool Group
2630 Superior Court
Auburn Hills, MI 48236
Phone: [phone]
Fax: [phone]
ASIA PACIFIC
India
Apex Power Tool India
Private Limited
Gala No. 1, Plot No. 5
S. No. 234, 235 & 245
Indialand Global
Industrial Park
Taluka-Mulsi, Phase I
Hinjawadi, Pune 411057
Maharashtra, India
Phone: [phone]
Australia
Apex Tool Group
519 Nurigong Street, Albury
NSW 2640
Australia
Phone: [phone]
China
Apex Power Tool Trading
(Shanghai) Co., Ltd.
2nd Floor, Area C
177 Bi Bo Road
Pu Dong New Area, Shanghai
China 201203 P.R.C.
Phone: [phone]
Fax: [phone]
Japan
Apex Tool Group Japan
Korin-Kaikan 5F,
3-6-23 Shibakoen, Minato-Ku,
Tokyo 105-0011, JAPAN
Phone: [phone]
Fax: [phone]
Korea
Apex Tool Group Korea
#1503, Hibrand Living Bldg.,
215 Yangjae-dong,
Seocho-gu, Seoul 137-924,
Korea
Phone: [phone]
Fax: [phone]
| Cleco®is a registered trademark of Apex Brands, Inc. | © 2017
England
Apex Tool Group GmbH
C/O Spline Gauges
Piccadilly, Tamworth
Staffordshire B78 2ER
United Kingdom
Phone: [phone]
Fax: [phone]
France
Apex Tool Group SAS
25 Avenue Maurice Chevalier - ZI
77330 Ozoir-La-Ferrière
France
Phone: [phone]
Fax: [phone]
Germany
Apex Tool Group GmbH
Industriestraße 1
73463 Westhausen
Germany
Phone: [phone]
Fax: [phone]
Sales Center
Service Center