Cleveland PRO GOLF DEMOUNT User manual

For AMC180 & 400 Rate controllers see other manuals on our website
For WGF Shrouded booms see other manuals on our website
Disclaimer:
Cleveland Alliances Ltd accept no liability for damage caused to the machine or the environment or per-
sons through operaon or misuse of the machine. The operator must be competent, trained, and have the
appropriate cercaon.
DO NOT USE THIS MACHINE UNLESS YOU HAVE BEEN TRAINED TO DO SO.
For technical support and spare parts assistance call 01361883418
Email us on [e-mail]
Cleveland Alliances Ltd
Staon Road, Duns, Berwickshire, TD113HS

Thank you for purchasing your Cleveland Gambe Sprayer. Here are the do’s and don’t of operaon and
how to keep spraying without any hassles.
Disclaimer:
Cleveland Alliances Ltd accept no liability for damage caused to the machine or the environment or persons
through operaon or misuse of the machine. The operator must be competent, trained, and have the
appropriate cercaon.
DO NOT USE THIS MACHINE UNLESS YOU HAVE BEEN TRAINED TO DO SO.
Spraying is a delicate operaon and involves the risk of contaminaon of people, animals and the environ-
ment. For this reason the funconality of all machine components must be carefully ensured. - The operator
is always the most exposed person to the used chemical products and he/she must always adopt all the nec-
essary measures for his/ her personal safety at work. Refer to the danger indicaons on the labels of the
products used. - Always work in the correct weather condions and follow the weather forecasts for the en-
re period of applicaon. - Dose the product to be poured into the tank correctly. - Make sure that the
chemical substances used are compable with the construcon materials of the machine. - Never leave
chemical substances on the tank for more than a few hours. - Carefully follow the regulaons concerning the
possession and use of plant protecon products and make sure that people and animals cannot access them.
- Aer each use carefully wash the containers of the mix and the dosing tools that have been used. - Do not
use the machine without hand washing tank or if it is not full. - The machine should be cleaned in the same
place where it is lled, i.e. an area where the water can be collected in a disposal manhole. - Do not dis-
charge the mixing residues to the watercourses, sewers and public areas.

FITTING TO THE TRUCK
NEVER WORK ON THE MACHINE WHILST THE ENGINE IS RUNNING
1. Connect the machine to the lower links onto the truck body using the jacking handles
to adjust the height. DO NOT PUT FINGERS INTO THE PIN HOLES WHEN ALIGNING THE
SPRAYER TO THE TRUCK. Connect the two rear pins and then connect the centre front
pin to the pping ram. Make sure all lynch pins / R pins are in place
2. When the machine is connected to the truck check the area is clear and li the
Sprayer using the pping ram. The connect the hydraulic pump hoses to the hydraulic
service on the truck. The engine should NOT be running when doing this.
3. Connect the electrical cables to the control boxes.
NEVER LIFT THE SPRAYER WITH THE TIPPING HYDRAULIC RAM WHEN THERE IS
LIQUID INSIDE THE TANK!

Do not just bash on, hoping you’re going to get it right!!! You’re applying thousands of pounds worth of
product… lets do a good job shall we…..
1. Connect to the TRUCK following the previous page instrucons. Make sure the sprayer chassis is
sing level and the nozzles are 50cm from the ground when the machine is at the working posi
on on the vehicle
2. Put water inside the tank. ONLY ADD PRODUCT when there is at least 150lt of water in the tank.
The pump MUST BE RUNNING via the hydraulic PTO when adding CHEMICAL. If you just add
chemical without the pump running you risk choking your sucon lter which will be a real pain in
the backside for you.
4. Add the rest of the water to the required level.
Controls:
Operaon:
Boom Secon Valves
The secons are controlled from the cab switch box
Pressure Balancing - To set the pressure balancing valves, follow this procedure:
1. Set the total boom spraying @ 3bar pressure
2.Turn o secon 1, if the pressure increases above 3 bar, turn the balancing valve an clockwise unl the pres-
sure is at 3 bar. If the pressure decreases below 3 bar, turn the balancing valve clockwise unl the pressure is
at 3 bar. Switch the secon back on so the whole boom is spraying. Repeat the procedure for secons 2,3,4,5
1
32
Pressure Relief valve
To set the relief valve, put
the PTO speed to 540
rpm and start spraying
water. Set the pressure
to 5 bar using the YEL-
LOW adjuster. Then un-
screw the green knob
(an clockwise) unl the
pressure drops to 4.8 bar
54

The switch box comes with a 12v ‘D’ plug for power. Modern tractors should come with a female D plug
installed. If it has not, get your dealer to install one. Push in cigaree lighter type sockets are not good
enough for professional 12v connecons.
Electric controls supplied as either 3 secon or 5 secon:
Boom secon switches
Operaon:
Spray On
Spray O
Whole boom
Pressure Increase
Pressure Decrease
Foam Marker
Le Boom Right Boom

Tank Sucon & Tank Drain
Underneath the main tank , at the rear of the machine is a valve which has 2 posions.
DRAIN POSITION
The valve must be
poinng RIGHT to allow
the tank contents to
drain out
MAIN TANK SUCTION OR CLEAN WATER SUCTION
Valve Arrow poinng RIGHT= Clean Water Sucon
Valve Arrow poinng LEFT = Main Tank Sucon
SUCTION FILTER LOCATED UNDER THE PUMP
To clean the sucon lter (WEEKLY) you must re-
move the yellow plunger rst. Once it is removed,
you should unscrew the large lter nut and remove
the lter element to clean. Be careful not to lose
the large lter O ring in the housing. Once
cleaned, put back together and make sure the l-
ter is fully assembled before replacing the yellow
plunger

To use the inducon hopper, there must be water in the main tank and the pump needs to be running at a minimum PTO
speed of 400rpm.
Main Sprayer Tank Rinse
Hose Reel (if ed)
Auxiliary Valve
Chemical Mixer Hopper
Internal Rinse
Agitator
Can Wash
Twist the hinged lid an
clockwise to open
Hopper Empty to
main tank
If the valve is at 3
oclock or 9 oclock posi-
on, the hopper will not
empty. To empty, turn
the valve to the 12
oclock or 6 oclock posi-
on
The pump need to be
running at a minimum
of 400rpm PTO speed
Arrow on the valve handle poinng towards the centre of
the hopper (le) means the hopper is on and ready to use
Arrow on the valve handle poinng towards the boom
(right) means the hopper is o and you are ready to spray.
THE MACHINE WILL NOT SPRAY IF THE HOPPER IS ON
Internal Bowl Rinse
Agitator inside the hopper
Chemical Can washer

Boom Operaon
6m boom
The 6m boom has 4 nozzles per boom secon at 50cm spacing. The boom is equipped with spring
adjusted break-back devices in case of collision. The tension on the springs can be adjusted by the 30mm
nut on top of the boom hinge. Do not make too ght. Doing so can cause too much rigidity and cause the
boom to bend in there is collision. Usually 20 to 25mm of thread above the adjustment nut is adequate.
To open the boom:
• Pull the right hand boom arm towards you and open it towards the right hand side of the machine.
Be sure to locate the boom in the fully open posion
• Once the right hand boom arm is secured, pull the le hand boom arm towards you and open it
towards the le hand side of the machine. Be sure to locate the boom in the fully open posion
On a weekly basis, APPLY GREASE to the folding mechanism when the boom arm is half way between be-
ing full open and fully closed. WARNING: DO NOT MOVE THE BOOM ARM WHEN YOU ARE GREASING
THE BOOM HINGE. YOU MAY TRAP YOUR FINGERS IN THE MECHANISM. TAKE NOTE
When opening, open RIGHT hand boom arm rst
When closing, close LEFT hand boom arm rst

Boom Operaon
6m Hydraulic/Electric Boom
8m Hydraulic / Electric Boom
The 6m boom has 4 nozzles per boom secon at 50cm spacing. The 8m boom has 4 nozzles in the centre,
3 nozzles on the rst secon and 3 nozzles on the second secon. The boom is equipped with spring
adjusted break-back devices in case of collision. The tension on the springs can be adjusted by the 30mm
nut on top of the boom hinge. Do not make too ght. Doing so can cause too much rigidity and cause the
boom to bend in there is collision. Usually 20 to 25mm of thread above the adjustment nut is adequate.
To open the boom:
• You will have 2 switches mounted on a box which has a 12v feed near the drivers posion
• You can open either boom at any me or both booms together. There is a fuse for each switch un-
derneath the switch on the external area of the switch box
On a weekly basis, APPLY GREASE to the folding mechanism when the boom arm is half way between be-
ing full open and fully closed. WARNING: DO NOT MOVE THE BOOM ARM WHEN YOU ARE GREASING
THE BOOM HINGE. YOU MAY TRAP YOUR FINGERS IN THE MECHANISM. TAKE NOTE
Golf 8m
Golf 6m

Nozzle Applicaon Chart