Climax Technology WTRQ Series User manual

1
E
Em me er rg ge en nc cy y P Pe en nd da an nt t / / W Wr ri is st t T Tr ra an ns sm mi it tt te er r ( (W WT TR RQ Q S Se er ri ie es s)
)
E
Ea as sy y & & E Ex xc ch ha an ng ge ea ab bl le e B Be el lt t / / N Ne ec ck k C Co or rd d s st ty yl le es s
L
Lo on ng g b ba at tt te er ry y l li if fe e
W
Wa at te er rp pr ro oo of f
The Wrist Transmitter/Emergency Pendant is designed to be worn by seniors as they
move on the premises. In an emergency, help is merely a button press away.
The WTRQ Series include the following models:
Model Name
WTRQ
WTRQ2
WTRQ3

 A Ac ct ti iv ve e B Bu ut tt to on n
 Pressing the Active Button for more than 1 sec will activate the Control Panel, causing it to dial
emergency call or alarm.
 Press and hold the Active Button for 8 seconds to send a Cancel Code to the Control Panel.
(This function is not compatible with every control panel).
 Press and hold the button for 15 sec (until the LED flashes 3 times) to activate the Auto Low
Battery Detection. WTRQ will automatically check battery voltage every 20-24 hours.

 L
LE ED D i in nd di ic ca at to or r
 Flashes three times: When Auto Low Battery detection
function is enabled. (WTRQ2 & WTRQ3)

 L Le ea ar rn n i in n t th he e T Tr ra an ns sm mi it tt te er r
Step 1. Put the Control Panel into the learning mode.
Step 2. Press the Button on the Transmitter, a radio signal will be transmitted to the Control
Panel.
Step 3. Please refer to the operation manual of your Control Panel to complete the learning
process.

 B Ba at tt te er ry y L Li if fe e
The Transmitter uses one CR2032 3V Lithium battery as its power source.
Every time the Active Button is pressed, the Wrist Transmitter will check the battery
voltage. If low battery is detected for 3 times successively, the Wrist Transmitter will enter
low battery status and transmit Low Battery signal along with regular signal every time the
button is pressed.
<
<N NO OT TE E> >

 A 30-second interval is required between each Active Button press to check the
battery voltage again.

 S Sw wi it tc ch hi in ng g B Be et tw we ee en n W Wr ri is st t B Ba an nd d/ /N Ne ec ck k C Co or rd d

2
Step 1. Take off the Wrist Band on the Transmitter.
Step 2. Clip the hook onto the Transmitter.
Step 3. Thread Neck cord through the hook.

 A Au ut to o L Lo ow w B Ba at tt te er ry y D De et te ec ct ti io on n
The Wrist Transmitter features Auto Low Battery detection function.
 Press and hold the Active Button for 15 seconds to activate this function (ignoring the
1st and 2nd set of LED flashes at the first and 8th seconds). The LED will flash three
times to confirm.
 After activation, the Wrist Transmitter will automatically check battery voltage every
20-24 hours. If low battery is detected for 3 times successively, the Wrist Transmitter
will enter low battery status and transmit low battery signal every 12 hours.
<
<N NO OT TE E> >

 If Auto Low Battery detection is not activated, the Wrist Transmitter will not
automatically check battery status. You need to check battery status by manually
pressing the Active Button.

 Once Auto Low Battery Detection is activated, it cannot be deactivated later in any
circumstances.

 C Co om mp pl li ia an nc ce e w wi it th h S St ta an nd da ar rd ds s
Complies with the requirements of the Radio Equipment Directive 2014/53/EU
Electromagnetic Compatibility Directive 2014/30/EU, Low Voltage Directive 2014/35/EU
Safety:
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
EMC:
EN 50130-4:2011+A1:2014
EN 301489-1:V2.2.0:2017
EN 301489-3:V2.1.1:2017
Radio: EN 300220-1:V3.1.1:2017
EN 300220-2:V1.1.1:2017
EN 300220-3-1:V1.1.1:2017
EN 300220-3-2:V1.1.1:2017
F
FC CC C S St ta at te em me en nt t
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
F
FC CC C C Ca au ut ti io on n: :
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance may void the user's authority to operate this equipment. (Example - use only
shielded interface cables when connecting to computer or peripheral devices).