Innova Pb570 User manual

1-11

CONTENTS

Advisory

Setup and Installation

Wireless Hand Control

1-2-20 year Warranty

Adjustable Base

PB570 Wireless

Owner Manual

With OKIN Refined Control

and Children Safety Lock

Manufactured by Innova Sleep Systems

For toll-free customer service, call 1-877-386-1373

email us: service@innovasleep.com

Please tell us your name, phone, address , serial No.

(found on the foot beam of the bed base ),

and the problem when you call/email.

11-11

2-11

this warranty; (d) to damage to mattresses, fabric, cables,

electrical cords or items supplied by dealers. Contact the

dealer for warranty information on these items; (e) if there

has been any modification of the adjustable bed base without

prior written consent by Innova; (f) to costs for unnecessary

service calls, including costs for in-home service calls solely for

the purpose of education the consumer about the adjustable bed

base or finding an unsatisfactory power connection; (g) if the

recommended weight restriction is not followed (refer to the

advisory section of this manual), the warranty will be void.

Repairs to or replacement of an adjustable bed base or its

components under the terms of this limited warranty will

apply to the original warranty period and will not serve to

extend such period. The decision to repair or to replace defective

parts under this warranty shall be made, or cause to be made, by

INNOVA at its option and in its sole discretion. Repair or

replacement shall be the sole remedy of the purchaser. There

shall be no liability on the part of Innova for any special, indirect,

incidental, or consequential damages or for any other damage,

claim, or loss not expressly covered by the terms of this

warranty. This limited warranty does not include

reimbursement for inconvenience, removal, installation, setup

time, loss of use, shipping, or any other costs of expenses,

Innova and/or its service technicians shall not be responsible

for moving furniture or any other items not attached to the

adjustable bed base in order to perform service on the adjustable

bed base . It is the sole responsibility of the purchaser to provide

adequate space and accessibility to the adjustable bed base . In

the event that the technician is unable to perform service due to

lack of accessibility, the service call will be billed to the purchaser

and the service will have to be rescheduled. Innova makes no

other or implied, and all implied

warranties of merchantability and fitness for a particular

purpose are disclaimed by Innova and excluded from this

agreement. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation

or exclusion may not apply to every purchaser. This warranty

gives the purchaser specific legal rights, and the purchaser may

also have other rights, which may vary from state to state. This

warranty is valid in all 50 states, Puerto Rico, and Canada.

warranty expressed

WARNING

Attention: Read the following information

before using this product . Failure to use a

surge protection device could compromise

safety or cause product malfunction could

void the electrical portion of your warranty.

and

Electrical surges are by far the biggest cause of problems with

electrical circuits.

In order to help protect your investment in case of a power surge or

outage, use an electrical surge protection device (not included).

WARRANTY WARNING!

Do not open or tamper with the transformer, control box, motors, or

remote control (with the exception of battery compartments). The

product warranty will be void if these components are tampered

with.

SMALL CHILDREN AND PETS:

Immediately dispose of all packing materials as they can smother

small children and pets. Do not allow any persons or pets under the

bed base . Children, convalescents and disabled person should not

operate the bed without adult supervision.

HOSPITAL OR CONVALESCENT USE DISCLAIMER:

Adjustable bed are designed and engineered for a life style of

in-home comfort and are not intended for hospital use or for a

bed-ridden patient on an extended recovery. Adjustable bed

are not equipped with bars to help patients get safely in and out of

bed base and are not intended to be used around tent type oxygen

therapy or explosive gases.

PACEMAKER WARNING:

The in this bed base produce mechanical vibrations

base

bases

massage

units

3-11

10-11

INNOVA SLEEP PRODUCT

1, 2 & 20 YEAR LIMITED WARRANTY

Innova Sleep , Inc. (“Innova”) warrants this adjustable bed

base to the consumer who is the original purchaser (the “purchaser”),

subject to the terms and conditions set forth herein. This warranty

begins on the “warranty commencement date” which is the date of

purchase for new unused beds base and the date of manufacture for

bed bases that have been used as floor or display models. Thus, on a

floor model bed base , the warranty is a portion of the limited 20 year

warranty.

FULL 1 YEAR WARRANTY

This adjustable bed base is warranted against defects in the

workmanship or materials for a period of one (1) year from the

warranty commencement date. Upon notice during the first year after

the warranty commencement date, Innova will repair or replace (at no

cost to the purchaser) any defective adjustable bed base part, and

INNOVA will pay all authorized labor and transportation costs

associated with the repair of replacement of any parts found to be

defective . When the adjustable bed base at hand is found to be

DAMAGED, not DEFECTIVE, all costs incurred to inspect and/or

correct the requested issue will be the financial responsibility of the

requesting party.

2 YEAR LIMITED WARRANTY

20 YEAR LIMITED WARRANTY

Systems

During the second year from the warranty commencement date,

upon receipt of written notice, INNOVA will replace any adjustable

bed base part found to be defective. Purchaser shall pay all service

and transportation costs related to the replacement of the defective

part . This limited two (2) year warranty shall not apply unless the

defective part is returned to INNOVA and INNOVA receive all service

and transportation cost .

Upon written notice during the third year through the from

the warranty commencement date, INNOVA will replace, upon term

and conditions set forth in this paragraph, any mechanical bed base

part found to be defective. Electronics, electrical components, drive

motors and massage motors are excluded .

. In years

3 - 20 years, purchaser shall pay all service and transportation costs

related to the replacement of the defective part and required to pay

1/20 of the current replacement cost of the parts times the number

of year used .

for validation

20th

This limited warranty shall

not apply unless the defective part is returned to INNOVA and INNOVA

receive all service and transportation cost for validation

ADDITIONAL TERMS AND CONDITIONS

This warranty does not apply; (a) to any damage caused by the

purchaser; (b) if there has been any repair or replacement of

adjustable bed base parts by an unauthorized person; (c) if the

adjustable bed base has been mishandled (whether in transit or by

other means), subjected to physical or electrical abuse or misuse, or

otherwise operated in any manner inconsistent with the operation

and maintenance procedures outlined in the Owner’s Manual and

may

activity and require a faster heart rate .

may experience a sensation similar to when you are exercising.

Consult your physician for further information.

PRODUCT RATINGS:

The bed base lift motors are not designed for continuous use of more

than 2 minutes in an 18 minutes period, or approximately 10% duty

cycle. Any attempt to circumvent or exceed this rating will shorten

the life expectancy of the product and may void the warranty.

WEIGHT UNITS:

The limitation for this adjustable bed is 750 lbs. The bed will

structurally support these weights, provided is evenly

distributed across the head and foot sections. This product is not

designed to support or lift this amount in the head or foot section

alone. Exceeding this weight restriction could damage the bed base

and/or cause injury and void the warranty. Enter or exit the bed base

in a flat position and do not sit on the head or foot sections while in

the raised position.

LIFTING AND LOWERING MECHANISMS AND MASSAGE UNITS:

It is normal for the raising and lowering feature on this bed base to

emit a minimal humming sound during operation. The massage

feature creates a vibrating hum during operation and the resonance

will increase accordingly with a higher intensity motor setting.

LOCATION ENVIRONMENT:

The level of sound experienced in a room is directly related to the

environment within that location. In a room with hardwood floors

and the turned on, a vibrating noise can be noticeable.

To reduce the resonance, place a piece of carpet or rubber casters

cups under the legs. The rubber caster cups also prevent the bed

base sliding when located on smooth or hard surface flooring.

that activate a special sensor in your pacemaker that detects

motion. This can fool the pacemaker into “thinking” you are engaged

in some sort of physical You

the weight

massage units

4-11

Use to raise and lower

the head of the bed base.

OKIN Wireless Remote

#PB570 Adjustable Bed

Base

Preset Position Buttons M1 M2

ZERO GRAVITY

1.Press the “FLAT” button to return the bed base to flat position .

2.Adjust the head and foot to desired positions .

3.Press the ‘TIMER” button until back light flashes , then

press “M1" / “M2" or “ZERO GRAVITY” button .

4.You can reset the 4 position buttons by repeating the

above steps .

Head Button

Flat Button

Press to return to flat position

Zero Gravity button

Preprogrammed for optimum

comfort and relaxation position

Memory 1 Button

Head Massage Button

Turn the head massage on and off Foot Massage Button

Turn the foot massage on and off

Timer Button

Press to stop all movement ,

adjusts the massage to 10 min ,

20 min , or 30 min .

Memory 2 Button

Massage Intensity

Button

Use to raise and lower

the foot of the bed base .

Foot Button

Lock buttons

Press these two buttons simultaneously

to lock the remote control

Unlock buttons

Press these two buttons simultaneously

to unlock the remote control

Adjust the intensity of the bed base ,

total three levels .

TO REDUCE THE RISK OF SHOCK, BURNS, FIRE OR INJURY:

Make sure the base is in a flat position and the vibrating motors are

turned off before unplugging the bed base from the power source.

Always unplug the base from the electrical outlet before cleaning or

servicing the base . If the cord or plug is damaged, discontinue use of

the bed base. Contact a qualified service personnel for examination

and repair.

FCC COMPLIANCE:

This device complies with part 15 of the FCC Rules for residential use.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

Radio Frequency: 2.4 GHz

EMERGENCY BATTERY BACKUP:

In the event that the base is stuck in an articulated position during a

power outage, the battery backup in the transformer can be used to

return the base to flat position . To use the battery backup, install

two 9-volt alkaline batteries into the battery backup transformer

(fig 1).Press the "Emergency Lowering"button on the control box

(see fig 9) to return the bed base to the level position . Alternately,

you can use the remote control to return the bed base to the level

position. First, press the "foot down" button. And then, press the

"head down" button . When using the battery backup, pressing the

"flat" button on the remote will not return the bed base to the level

position.

Please note that batteries are for backup only and are not to be used

for normal operation of the bed base.

Figure 1

1) Unlock the children safety lock by pressing the button and

the button simultaneously .

2) Deactivate the children safety lock function by pressing the

button and the button simultaneously .

Activate the children safety lock function by pressing the

button and the button simultaneously or by pressing the

button and the button simultaneously .

Deactivate children safety lock:

Activate children safety lock

9-11

5-11

8-11

Figure 8 Figure 9

CYNCHRO

CNTL

SETUP and INSTALLATION

Important: We strongly recommend

two able-bodied adults setup and

assemble this product.

Step 1:

Check and verify all parts are included before discarding any packing

materials.

All electronics and components that need to be installed are located

in boxes under the base or attached to the frame.

A)Wireless Remote Control (1)

B)Mattress Retainer Bar (1)

C)Legs (4)

D)Power Cord (1)

E) Extension Cord (1)

F)Transformer with emergency battery backup (1)

G)Control Box (1)

Step 2:

With the help of your able-bodied assistant, place carton on floor

with arrows point downwards.

Step 3:

Connect the Transformer “F” to Control Box “G” : The Control Box

is the Black Box attached to the bottom of the bed base . Connect

one side of Extension Cord “E” with the Control Box “G” and plug

another side of Extension Cord “E” into Transformer “F” . Extend the

Power Cord “D” plug into Transformer “F” . (See Figure 2)

Figure 2

Setup is now complete. Enjoy.

USING SAME REMOTE:

Connecting the two control boxes with the cable .

Plug one side of the cable into the “CYNCHRO CNTL” on the side of the

control box and plug another side into the “CYNCHRO CNTL” on the

side of another control box ,

The bed base is designed to allow two twin X-Long bases to become

an Eastern King base and two Split-Cal-King bases to become a Cal-

King base. can use the same remote to control two side by

side bed bases by

Owner

Each remote must have a different DIP-switch setting.

then you can connect two control boxes

(See figure 8&9) .It is important that the two control boxes

expected to work synchronously must be still configured differently

to pair with the different remote control with different DIP-Switch

position. Do not pair both control boxes with the same remote control ,

7-11

6-11

Figure 3

Figure 6 Figure 7

Step 8:

-Unplug the Power Cord.

-Install the four legs firmly into the base of the frame. The legs screw

into the threaded holes in each corner of the adjustable base frame

(See Figure 3).

-Do not over tighten

Step 9:

With the help of your able-bodied assistant , carefully lift the

adjustable bed base frame and set it in place upright on its legs .

Excessive pressure may damage the legs. Remove all protective

plastic covering .Note: check and make sure that all power cords

clear and do not interfere with any Adjustable Bed base Mechanisms

Dispose of covering to avoid injury.

Step 10:

Note : The Mattress Retaining Bar is mounted upside down for

shipping only . Remove the Mattress Retaining Bar on the foot of the

bed base and turn the bar upright and by carefully aligning

and pushing the bar into place . the retaining clips to secure

the bar into place . (See Figures 6 & 7. )

plastic properly

re-install

Insert

Step 4:

Push the DIP SWITCH on the remote to a certain position

(different from the position on the other remote) , if you have more

than one adjustable bed base .

Step 5& 6:

Plug electrical cord into a grounded electrical outlet.

Using the Wireless Remote, push the Foot Massage Button and Foot

Down Button until flashes to unlock , then push the Head

Up button, Foot Up button , the vibrating motor and Flat Button for a

momentary test of the Wireless Remote.

If the motor

is working quickly let go of the button and skip to step 8.

Step 7:

Synchronize the remote with the control box. First find the black box

mounted under the bed base . Press the black LINK BUTTON until the

LINK LED flashing , then press HEAD UP and FOOT UP buttons

simultaneously until the back light on remote control flashing . The

adjustable bed base should be working after matching the remote

with the control box . Press the Head Up button

to test . We strongly recommend that

each control box must be matched with different remote controls

where the DIP SWITCH positions are different .

There is a red Emergency Lowing

button on the control box .

Locate the Wireless Remote control and insert 3 AAA batteries (See

Figure 4) .

, Foot Up button , the

vibrating motor and Flat Button

When the remote control is not working ,

it adjusts bed base to the level position (See Figure 5) .

LED light

Please note that the actuator

is a gravity down motor ,it needs weight to come down .

Do not match both

control boxes with the same remote control . Each remote must have a

different DIP SWITCH setting .

pressing

LINK

BUTTON

LINK

LED

Emergency Lowering

Figure 4 Figure 5

DIP SWITCH

7-11

6-11

Figure 3

Figure 6 Figure 7

Step 8:

-Unplug the Power Cord.

-Install the four legs firmly into the base of the frame. The legs screw

into the threaded holes in each corner of the adjustable base frame

(See Figure 3).

-Do not over tighten

Step 9:

With the help of your able-bodied assistant , carefully lift the

adjustable bed base frame and set it in place upright on its legs .

Excessive pressure may damage the legs. Remove all protective

plastic covering .Note: check and make sure that all power cords

clear and do not interfere with any Adjustable Bed base Mechanisms

Dispose of covering to avoid injury.

Step 10:

Note : The Mattress Retaining Bar is mounted upside down for

shipping only . Remove the Mattress Retaining Bar on the foot of the

bed base and turn the bar upright and by carefully aligning

and pushing the bar into place . the retaining clips to secure

the bar into place . (See Figures 6 & 7. )

plastic properly

re-install

Insert

Step 4:

Push the DIP SWITCH on the remote to a certain position

(different from the position on the other remote) , if you have more

than one adjustable bed base .

Step 5& 6:

Plug electrical cord into a grounded electrical outlet.

Using the Wireless Remote, push the Foot Massage Button and Foot

Down Button until flashes to unlock , then push the Head

Up button, Foot Up button , the vibrating motor and Flat Button for a

momentary test of the Wireless Remote.

If the motor

is working quickly let go of the button and skip to step 8.

Step 7:

Synchronize the remote with the control box. First find the black box

mounted under the bed base . Press the black LINK BUTTON until the

LINK LED flashing , then press HEAD UP and FOOT UP buttons

simultaneously until the back light on remote control flashing . The

adjustable bed base should be working after matching the remote

with the control box . Press the Head Up button

to test . We strongly recommend that

each control box must be matched with different remote controls

where the DIP SWITCH positions are different .

There is a red Emergency Lowing

button on the control box .

Locate the Wireless Remote control and insert 3 AAA batteries (See

Figure 4) .

, Foot Up button , the

vibrating motor and Flat Button

When the remote control is not working ,

it adjusts bed base to the level position (See Figure 5) .

LED light

Please note that the actuator

is a gravity down motor ,it needs weight to come down .

Do not match both

control boxes with the same remote control . Each remote must have a

different DIP SWITCH setting .

pressing

LINK

BUTTON

LINK

LED

Emergency Lowering

Figure 4 Figure 5

DIP SWITCH

5-11

8-11

Figure 8 Figure 9

CYNCHRO

CNTL

SETUP and INSTALLATION

Important: We strongly recommend

two able-bodied adults setup and

assemble this product.

Step 1:

Check and verify all parts are included before discarding any packing

materials.

All electronics and components that need to be installed are located

in boxes under the base or attached to the frame.

A)Wireless Remote Control (1)

B)Mattress Retainer Bar (1)

C)Legs (4)

D)Power Cord (1)

E) Extension Cord (1)

F)Transformer with emergency battery backup (1)

G)Control Box (1)

Step 2:

With the help of your able-bodied assistant, place carton on floor

with arrows point downwards.

Step 3:

Connect the Transformer “F” to Control Box “G” : The Control Box

is the Black Box attached to the bottom of the bed base . Connect

one side of Extension Cord “E” with the Control Box “G” and plug

another side of Extension Cord “E” into Transformer “F” . Extend the

Power Cord “D” plug into Transformer “F” . (See Figure 2)

Figure 2

Setup is now complete. Enjoy.

USING SAME REMOTE:

Connecting the two control boxes with the cable .

Plug one side of the cable into the “CYNCHRO CNTL” on the side of the

control box and plug another side into the “CYNCHRO CNTL” on the

side of another control box ,

The bed base is designed to allow two twin X-Long bases to become

an Eastern King base and two Split-Cal-King bases to become a Cal-

King base. can use the same remote to control two side by

side bed bases by

Owner

Each remote must have a different DIP-switch setting.

then you can connect two control boxes

(See figure 8&9) .It is important that the two control boxes

expected to work synchronously must be still configured differently

to pair with the different remote control with different DIP-Switch

position. Do not pair both control boxes with the same remote control ,