Clover HDC211 User manual

INSTRUCTION
MANUAL
TRUE DAY/NIGHT
VARI-FOCAL COLOR DOME CAMERA
MODEL HDC211
Copyright ©2009 Clover Electronics U.S.A. All Rights Reserved.

•To avoid electrical shock, do not open the case of this product.
•Do not stamp fingerprints on the lens.
•Operate this product using only the recommended AC Power supply.
•Do not overload electrical outlets or extension cords; this can result in fire or electric
shock.
•Keep this product away from strong magnetic fields.
•Do not expose this product in direct sunlight or strong reflected rays.
•Refer servicing to qualified personnel only.
•Do not change or modify this product, the warranty will be voided.
•Weatherproof (IP67)
•1/3” Sony Super HAD CCD
•High Resolution 550 TV Lines (Color), 600 TV Lines (B/W)
•True Day/Night (Built-in ICR: IR Cut Filter Removal)
•3D DNR (Digital Noise Reduction) with 3D filter
•D-WDR (Digital Wide Dynamic Range)
•3-Axis Gimbals Bracket
•Total 33 Infrared LEDs with a CDS sensor
•Up to 100’ IR range (depends on scene reflection)
•DC Auto Iris Vari-focal Lens (2.8-12mm)
•Dual Voltage(AC 24V/DC 12V)
1. Loosen the locking screw①with the provided hex-head wrench and turn the locking
ring②counter-clockwise to remove the transparent dome③.
2. Attach the camera base④to the wall or ceiling, wherever you want to install the
camera. Locate a wall stud or ceiling joist and secure the camera base④using the
supplied screws⑤.
3. How to set angle of view:
- Loosen the screws⑥ for tilting and adjust the camera direction by moving the
camera body⑧up or down, then fix the screws firmly.
- Turn the mounting bracket (metal part) covering the camera body⑧left or right for
panning adjustment.
- Loosen the locking knob⑦ and turn the camera body⑧clockwise or counter-
clockwise to upright images on the screen.
PRECAUTIONS
FEATURES
INSTALLATION

4. If necessary, change the settings to get the best images depending on your application
by using the buttons in the camera (refer to the instruction manual for OSD control).
5. Assemble the transparent dome③by turning the locking ring②clockwise. The
locking ring②should be securely fastened so that water can not leak into the camera.
6. Connect the one end of BNC cable (not supplied) to the BNC (F) of 5’ cable attached
to the camera and the other end (BNC) of cable to the video devices such as DVR,
monitor/TV. Plug an AC power supply (not supplied) to the DC jack (red) on the
camera.

1. Vari-focal lens①
Easily changeable angle of view: 2.8 to 12mm
2. T↔W (Tele ↔Wide)③
Turn this adjustment knob③clockwise or counter-clockwise to set the focal length.
3. ∞↔N②
Turn this adjustment knob②clockwise or counter-clockwise to set the focus.
4. After setting the focus and focal length, the adjustment knob② and ③ should be
securely fastened.
5. Do not stamp your fingerprint on the lens and dome, which may affect picture quality.
HOW TO ADJUST ANGLE OF VIEW

If the camera does not function properly, check the following points before contacting the
service center.
Troubles Remedies
No video Check the AC adapter and video cable
between the camera and a monitor
The image on the screen is dark Check the brightness control on the
monitor
The image on the screen is dim Check if the lens is stained. If dirty,
clean it with soft and clean cloth
The camera is not working properly, and
the surface of the camera case is hot
Check if you have connected the
provided AC adapter
The contrast on the screen is too weak Adjust the contrast feature of the
monitor. If the camera is exposed under
too strong light, change the position
The image on the screen flickers Does the camera face to directly to the
sunlight or fluorescent light? Change the
camera position
Picture rolls and jumps, scrambled
picture
Improper V-hold control. Setting on your
monitor
Picture smaller than screen House current may be too low
Note:
▪ Apply DC12V 1 A regulated power supply (not included).
▪ To avoid fire or shock hazard, use a UL listed power supply.
TROUBLE SHOOTING

•Image sensor 1/3” SONY Super HAD CCD
•Total pixels 811(H) x 508(V)
•Effective Pixels 768(H) x 494(V)
•Scanning system 2:1 Interlace
•O.S.D Available
•Backlight Off / HSBLC / BLC selectable
•Resolution 550TV Lines(color),600TV Lines(B/W)
•S/N (Y signal) 52dB (AGC Off, Weight On)
•Min.illumination 0.000006Lux(IR LED ON)
•White Balance ATW / AWB / Manual / AWC→SET
•Sense-up Off / Auto / (Selectable limit x2 ~ x258)
•3 DNR Off / On (1~50 level adjustable)
•D-WDR Indoor / Outdoor / Off
•D&N selection Color / BW / Auto
•Digital zoom On(x32) / Off
•Hosing material Die cast Aluminum alloy
•Dome material Polycarbonate
•Voltage AC 24V / DC 12V(Dual voltage)
•Current consumption 480 mA( LED: On), 170 mA(LED: Off)
•Lens DC Auto Iris Varifocal Lens (2.8mm-12mm)
•Operating temperature/Humidity -10°C ~ +50°C. RH 95% Max.
•Storage temperature/Humidity -20°C ~ +60°C. RH 95% Max.
•Dimensions 140 (Ф) x 100mm
•Weight 2 Lbs
This warranty gives the original purchaser specific legal rights and you may also have
other rights, which vary from state to state. If our products do not function because of any
defect in material or workmanship, we will repair free of charges for 2 years on parts and
labor from the date of original purchase. This warranty does not cover modification,
abuse, incidental or consequential damages unless the state of owner’s residence specially
prohibits limitations on incidental or consequential damages.
SPECIFICATIONS
LIMITED 2 YEAR WARRANTY

1. Original purchaser must fill out a warranty card and mail it to the factory with model
number, serial number and the date of purchase.
2. We will repair or replace, and return to the owner the system under this limited
warranty.
3. Please pack the system carefully and securely using the original packing materials,
and send it prepaid and insured to: 13073 E. 166th St, Cerritos, CA 90703.
4. Please include a check for $20.00 to cover the cost of return postage and handling. If
the system is returned within the warranty period, please include a proof of purchase.
If the system is out of warranty, you will receive an estimate of the repair cost for
your approval before repair work will be begun.
CDR0460 Stand-alone 4 CH Digital Video Recorder (DVR)
CDR4450 Stand-alone 4 CH Digital Video Recorder (DVR)
CDR0860 Stand-alone 8 CH Digital Video Recorder (DVR)
CDR1660 Stand-alone 16 CH Digital Video Recorder (DVR)
CDR0850 Stand-alone 8 CH Digital Video Recorder (DVR)
CDR1650 Stand-alone 16 CH Digital Video Recorder (DVR)
CA100BP 100’ BNC/Power to BNC/Power Extension cable and coupler
ADT121500 AC Power Supply DC12V 1.5 A Regulated
1-Day & Night Vari-focal Color Dome Camera
1-Hardware Accessories Kit
1-Instruction Manual
1-Instruction Manual for OSD Control
1-Warranty Registration Card
HOW TO OBTAIN FACTORY SERVICE
AVAILABLE ACCESSORIES
PACKAGE INCLUDES