CMD Reach Plus Dual User manual

127mm
150mm
538mm
55mm
490mm
705mm
6
3
5mm
ma
x
.
Use 2.5mm Allen key to
loosen grub screw and
allow arm assembly to
drop into base stem.
Designed to t onto desks with 19-30mm
thickness with the included clamp.
Carefully insert the pin
at the bottom of the
arm assembly into the
base stem.
If 180° lockout is
required, ensure bush
protrusion sits in recess
at bottom of the arm.
Tighten the grub screw
to secure the arm
assembly to the base.
Do not overtighten.
Use 4x M5x25mm bolts
to x the handle and
horizontal rail to the
head of the arm.
The rail is now fully
assembled and ready
for the monitors to be
installed.
Fix quick release VESA
in place with supplied
xings. 4x M4x12/16mm
CSK pozi screws.
Align the raised square
section on the VESA
with the recess on the
rail mount.
Lower the monitor onto
the rail mount until it
clicks into place. Repeat
for the second monitor.
To remove the monitors,
start by disconnecting
any cables.
Depress the lever at
the top of the VESA to
release it from the rail
mount. Lift up monitor.
The arm may try to
spring up as the weight
is removed. Guide the
arm to prevent this.
The nylon bush can be
removed, ipped and
retted to remove/apply
the 180° lockout.
Flip the bush over so
the protrusion faces
upwards to apply the
180° lockout as shown.
Place the clamp cover
over the base with the
recess facing the desk
edge. No xing required.
Ensure the EVA pad is
applied to the bottom of
the base to protect the
desk surface.
Use the supplied M8x20mm grub screws in the clamp if more thread is required
Place base on desk with
recess facing the edge.
Offer up the clamp to
the base as shown.
Use 4mm Allen key to
tighten the 2x grub
screws in the clamp into
the base.
Mounting the base to the desk
Dimensions
Installing monitors (max width of 635mm/25” per monitor)
‘CLICK’
Nylon bush in no lockout
position
Nylon bush in 180° lockout
position
2.5mm
4x M5x25
8x M4x12
8x M4X16
8mm4mm 6mm
Installing the arm and horizontal rail
Reach Plus Dual Installation, user and care guide
Contents
x1
x2
x1
x1
x2
x1 x1 x1
x1
x1
x1
x1
x1
2x M8X20
Add pad to
clamp if
required
Part No: 134222 Issue No: 004

CMD Ltd, Rotherham, S65 1EN, UK
T: 01709 829 511 E: [email protected]
15kg
max
No power tools
Additional information
• Fix the clamp of the monitor arm to a suitable solid worksurface that is capable of supporting the arm and maximum loading of 15kg.
• Product to be used only for the intended purpose of supporting certain display equipment in an ofce environment.
• Installation is to be carried out in accordance with relevant Health & Safety regulations and only to be carried out by a skilled or competent person.
• The installation should be installed to comply with the relevant national standards and be inspected and tested prior to being put into service (in the
UK BS 7671 Wiring Regulations or BS 6396 Ofce and Educational Systems Best Practice).
• Isolate the supply before installation or repositioning. Any locking mechanisms must be used and fully engaged.
• Do not misuse, dismantle or re-congure the product because doing so will invalidate the warranty.
Safety
• Refer to the Declaration of Conformity.
Standards
• To maintain the longevity of the arm’s gas strut and correct function, regularly adjust the arm through it’s range of motion when possible.
• Clean using a dry cloth. No abrasives or solvents to be used on the product.
• Do not drop or expose to moisture.
Product care
Feed the cables through
the built in cable clip on
the upper arm assembly
as shown.
Remove the plastic
cover on the lower arm
assembly by sliding it up
and away from the arm.
Position the cables inside
the cover and slide back
into place on the arm.
Feed cables from
monitors through the
cable clips as shown.
Use the central handle
to pivot the rail left or
right by a small amount.
Adjust the monitor arm
with the upper section
parallel to the desk
surface as shown.
For further adjustment,
use the supplied 4mm
Allen key to loosen or
tighten the 3x bolts.
Adjust both mounts if
necessary to achieve the
optimum placement of
your monitors.
The maximum combined
load of two monitors on
the rail is 15kg.
Insert the cable clips
with cables into the rail
by gently exing and
snapping into place.
If necessary, the level of
friction can be controlled
using the 6mm Allen key
on the central bolt.
Use 6mm Allen key to
turn bolt clockwise for
heavy monitors. Use free
hand to guide the arm.
Bolts must be tightened
equally, alternating
between each until they
are all fully tightened.
Neaten up the cables if
necessary, ready to feed
the cables to the arm
assembly.
Use 6mm Allen key to
turn bolt anti clockwise
for lighter monitors. Use
free hand to guide arm.
Cable management Rail angle adjustment
Arm adjustment
Rail mount adjustment
Supported load
3x Bolts
1/4
turn
1/4
turn
1/4
turn