CMP Wireless TROLLMaster PRO3+ User manual

P/N TMPRO3PLUS
02MANTMPRO3PLUS V3

Page 2
Congratulations on your purchase of the Wireless TROLLMaster PRO3+. This
addition to the TROLLMaster lineup will allow you to control both your trolling
speed and direction from anywhere in the boat.
CONNECTIONS
Power/Battery Connection 6’ (1.8m) Red, 6’ (1.8m) Black
Connect the red 16AWG to positive 12V battery terminal. Connect the black
16AWG to negative 12V battery terminal.
ACC+ Switched Power 15’ (4.6m) Red
Connect red 18AWG wire to switched accessory power at helm station.
2 Way Molded Connector 6’ (1.8m)
This connection is used to attach a Panther Electro Steer unit. Push the molded
connector to the corresponding connector on the Electro Steer unit until it is
snug and both ends of the connector meet.

Servo Connection 8’ (2.4m)
This wire will connect to the included Servo that mounts under the cowling of
the motor. For more details on how to install this servo refer to the Hardware
Kit you purchased that corresponds to vout specic make of motor. Route
and secure servo cable as far away as practical from the spark plug wires.
Pairing button
Pushing this button will pair your remote to your receiver. Push this button
once and the Activity light will be solid. Then press any button on the remote.
Once the light goes o, your remote is paired.
Activity Indicator
This blinks any time there is activity between your receiver and remote. It will
also be solid when you are in the process of pairing your remote.
Receiver Antenna
This wire is used for the receiver to be able to communicate to the remote. It can
lay loose and does not need any install attention.
MOUNTING HOLES
The holes are used to mount your receiver to ensure it is secure and will not
be tossed around while the boat is in motion.
QUICK START
1. Install your servo and throttle rod following the directions that come
with the hardware kit.
2. Find a suitable location to install your receiver that will be out of direct
contact with constant water exposure and can be mounted securely but
allows all cables to reach their destination.
3. Run your power cable from your receiver to your battery
4. Run your Acc+ Switched Power cable to helm station
5. Run your servo cable from your receiver out to your servo that was installed
on the kicker motor in Step 1.
6. (Optional) Connect your Panther Electro Steer motor to the 2 Way molded
connector on the receiver.
7. Pair your remote (See ‘Pairing button’ above)
8. Verify proper operation of the servo (and steering if connected).
9. Go shing!
For information on motor specic installation of the servo, please
refer to the installation instructions found at the Trollmaster website:
trollmasters.com/wireless/trollmaster-pro3/installation-guides/
Page 3

Page 4
Power
On/O
Backlight
LSD
Screen
Idle/Resume
Left/Right
Steering*
2 AAA
Batteries
Replace by
removing
two screws
Lanyard Hook
Max
Throttle
Faster
Slower
REMOTE FUNCTIONS
POWER
Power On
To power on your remote, push the Power On/O button for one second.
You will see TROLL Master on the screen. Select any function to start using
the remote.
Power O
To power o your remote, push the Power ON/O button for two seconds
until the display clears.
Sleep Mode
If you do not touch any buttons for one minute, the remote will go into sleep
mode. In order to wake it, touch any button on the remote and it will resume to
your last used function.
Batteries
The remote runs on two standard AAA batteries. You will get a ‘Low Battery’
indication on the screen when it is time to change them.

THROTTLE CONTROL
You have a range of 1-250 to adjust your speed. This does not correlate to
your actual GPS speed. Use an external GPS in order to get an accurate speed
reading for your situation.
Speed Adjustment
There are two buttons to control your speed, a rabbit icon for increasing
your speed and a turtle icon to decrease your speed. Press one time on the
corresponding button to change your speed in single increments.
Jog
If you hold down on either speed button for four seconds your increments
will increase by 10. Release the button and then press once again to go back
to increasing by single increments.
Feature buttons
These two buttons will allow you to max out the throttle control [approx.
80% of factory throttle], or return to idle.
Max Throttle
To use this feature you need to depress and hold the Max Throttle button. You
will see ‘Max Throttle’ appear on the screen while it is being held down, and your
motor will increase speed and stay at that Max Throttle as long as the button
is held down. To return to your previous speed setting, release the button.
Idle/Resume
To use this feature press the Idle button. When you do, the throttle will drop
to the 000 setting and it will say ‘Idle 000’ on the remote. To resume your
previous setting press the Idle button again. You will see ‘Resume XXX’. The
XXX will be the setting you had last been congured for.
STEERING CONTROL
When your unit is connected to a Panther Electro Steer (sold separately,) you
are able to remotely steer your kicker motor. Press once on the Left or Right
Arrow button on the remote to move in small increments. If you hold down the
button it will move in larger increments. See Installation Steps for more details.
Page 5

Page 6
INSTALLATION INSTRUCTIONS
1. Packaged in the hardware kit that you purchased with your PRO3+ is an
install manual that explains in detail how to Install your servo and throttle rod.
2. Your wireless receiver needs to be placed in a location where it will not
be exposed to constant water exposure. A battery compartment, rod box,
anything similar would be a good location.
Keep in mind that this location also needs to allow for the wires to be able
to reach the battery, servo, steering, etc. As an additional consideration, the
signal between your remote and receiver is designed to work within a ~30ft
(9.1m) range even inside of an enclosed location.
Once you nd a suitable location, use the mounting holes and appropriate
hardware to secure it.
3. The main power leads connect directly the 12V battery using the ring
connectors provided. Red to +ve terminal, Black to -ve terminal. The positive
wire includes a standard blade fuse.
4. The ACC+ Switched power should be connected to a +ve 12V switched power
source at the helm station. When the outboard engine is not in use, the
switched power should be powered down.
5. The servo wire from your receiver needs to be routed to the servo mounted
on your kicker motor.
NOTE: If you need an extension to your servo cable, visit trollmasters.
com and look for the Parts Shop link. There is a 10ft (3m) extension
available. To minimize the impact of EMI, take care to route and secure
servo cable as far away as practical from the spark plug wires.

Page 7
6. (Optional Steering Device) Route the steering cable 6ft (1.8m) from your
receiver to the location of your Panther Electro Steer motor and connect
the 2-Way molded connector until they are fully engaged. Do not plug
into the 3-way molded connector in an existing relay control.
NOTE: Keep in mind that depending on which side your electro steer is
mounted on your kicker motor the turn controls might be reversed. To
change this you can reverse the polarity of the connection. First, disconnect
the unit from the battery. Then cut the wires between the receiver and
connector. Now reconnect the wires, but connect red to black and black
to red. Be sure to use proper connections, like Butt T splices or wire nuts.
7. Pair your remote to your receiver. Push the pairing button on the receiver
and you will see a solid activity light. Then press any button on the remote.
Once the light goes o your remote is paired. It will always pair to the
most recent unit. If you need to replace your remote, following this step
will pair your new remote and does not store you older remote.
8. Once everything is connected and paired, ensure that operation is correctly
working by using your remote to verify that the servo (and steering)
are responding to inputs. Once this has been veried, tie down any loose
cables securely.
TROUBLESHOOTING
Inputs to remote do not cause the servo or steering to respond.
• Double check that your battery that is charged.
• Verify that your power cables are connected securely.
• Try pairing the remote one more time and ensure that the Activity Light
comes on to verify power.
• Check that the screen on the remote is in fact showing any kind of text
after pushing the power button. For testing ensure there is a clear line of
sight between the remote and the receiver. Once that works place back
in your preferred location and retest.
• There is a optional wired remote that can be purchased to verify wireless
receiver functionality. Visit trollmasters.com and look for the Parts Shop link.

Page 8
SERVICE AND WARRANTY
Should your unit ever require service, please do not return the product to
your dealer. Please call the number below for special instructions on shipping
and handling. Please call between 9:00 am - 4:00 pm (Central Standard Time)
Monday through Friday. If service is required and covered by warranty, it will be
repaired or replaced as described below.
If service is required and not covered by warranty, (such as damage caused
from improper trailering or from water intrusion through the breather tube),
replacement parts are available for purchase and may be paid for by Visa or
MasterCard.
The warranty coverage on this equipment is limited to the terms set forth
below: CMP Group LTD. warrants this product to be free of defects in material
and workmanship for a period of ONE (1) YEAR from the date of original retail
purchase. Positive proof of date of purchase is required for warranty service.
If service is required and covered by warranty, the unit will be repaired or replaced
with new or factory rebuilt parts at no charge. The defective components must
be returned to the address specied, with shipping charges prepaid. Be sure
to include your name, address, telephone number and a copy of the sales
receipt showing the date of original retail purchase. All sales receipts are subject
to verication.
This warranty does not apply if the unit has been damaged by accident, abuse,
misuse, poor installation or misapplication, or if it has been modied from its orig-
inal condition, or if any serial number has been removed or defaced or altered.
This warranty does not cover any expense to remove or reinstall the unit
or any of its components. If a returned unit is not covered by warranty, the
sender will be notied and given an estimate of the charges to repair or replace
the unit, together with the return shipping charges.
THIS WARRANTY DOES NOT COVER SPECIAL, INCIDENTAL, OR CONSE-
QUENTIAL DAMAGESRESULTINGFROM ANYBREACH OFWARRANTY,OR
UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO
DAMAGE TO OR REPLACEMENT OF OTHER EQUIPMENT AND PROPERTY.

THE WARRANTY AND REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU
OFALLOTHERS,WHETHERORALORWRITTEN,EXPRESSORIMPLIED.DUE
TO THE SPECIAL AND UNIQUE CONDITIONS THAT MAY EXIST IN EACH
APPLICATION, THE MANUFACTURER SPECIFICALLY DISCLAIMS ANY
AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. NO DEALER, AGENT OR EMPLOYEE IS
AUTHORIZED TO MAKE ANY MODIFICATION, EXTENSION OR ADDITION
TO THIS WARRANTY.
Some states do not allow exclusion of incidental or consequential damages, so
the above exclusions may not apply to you. This warranty gives you specic
legal rights, and you may also have other legal rights, which may vary from
state to state.
FOR SERVICE CALL [phone]
CMP Group LTD.
7733 Progress Way, Delta, BC,
Canada V4G 1A3
https://trollmasters.com/
Page 9

LANYARD STOP SWITCH EXTENSION
The purpose of a lanyard stop switch is to turn o the engine when the operator
moves far enough away from the operator’s position (as in accidental ejection
from the operator’s position) to activate the switch. Please refer to your Lanyard
Stop Switch (or similar) section of your manual for all information related to
that safety feature. This documents is NOT a replacement for that section
of your owner’s manual.
With the TROLLMaster being a wireless solution you can move farther than the
standard lanyard length that is provided with a standard Lanyard Stop Switch.
This extension is provided in the package for you to be able to move farther
than the standard 122cm and 152cm (4 and 5 feet). This extension should be
connected to the clip end of the existing stop switch lanyard and the other end
clipped to the operator securely.
There are more robust solutions that can be used in place of the lanyard exten-
sion if so desired. Doing an Internet search of “Wireless Marine Safety Devices”
would direct you to such items available. TROLLMaster does not endorse or
support any one solution.
One other item for safety to keep in mind is the use of the Steering Friction Con-
trol, especially on Tiller Steering outboards. This should be set just high enough
that the engine won’t turn on its own without input from the operator, at any
tilt position. If this is set too low and the operator lets go of the tiller (i.e., to grab
a hat blowing o their head) the engine can turn abruptly and possibly throw
the operator out of the boat.
WARNING
To avoid serious injury or death due to ejec-
tion from the boat, always attach the emer-
gency safety switch lanyard (with or without
the extension) to the switch & the operator.
In addition always have the outboard steer-
ing friction adjusted as instructed.
Page 10

Page 11
FCC: 2AILDTMPRO3PLUS
IC: 21604TMPRO3PS
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Federal Communication Commission Interference Statement
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux ap-
pareils radio exempts de licence.
L’exploitation est autorisee aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme
si le brouillage est susceptible d’en compromettre le fonctionnement.

EXPAND YOUR PANTHER EXPERIENCE
WITH THESE CMP GROUP BRANDS:
Solutions for motor mounting, remote
steering, tilt & trim, shallow water anchors,
and security systems.
Rod holders, trolling motor supports, and
GPS/Sonar mounts.
Auxiliary outboard motor steer systems.
Throttle control for gas powered auxiliary
motors.
www.cmpgroup.net
02MANTMPRO3PLUS V3
12 pages, A5