CNC Design QUAD COIL WINDER MK2 User manual

CNC GUITAR PICKUP QUAD COIL
WINDER MK2
INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY
TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS MACHINE.
Version 1 –17/05/2023

[1]
CONTENTS
Declaration Of Conformity.................................................................................2
Specification.......................................................................................................3
Warranty............................................................................................................3
Safety Warning...................................................................................................4
Maintenance......................................................................................................4
Getting To Know Your Coil Winder ....................................................................5
Operation And Use..........................................................................................6-7
Installing Software ........................................................................................8 - 9
GENERAL INFORMATION
This manual has been compiled by CNC Design Ltd and is an integrated part of the product with which it is
enclosed and should be kept with for future references.
This manual describes the purpose for which the product has been designed and contains all the necessary
information to ensure its correct and safe use. We recommend that this manual is read before any operation or,
before performing any kind of adjustment to the product and prior to any maintenance tasks. By following all the
general safety instructions contained in this manual it will ensure both the product and operator safety, together
with longer life of the product itself.
All photographs and drawings in this manual are supplied by CNC Design Ltd to help illustrate the operation of
the product.
Whilst every effort has been made to ensure accuracy of information contained in this manual, the CNC Design
Ltd policy of continuous improvement determines the right to make modifications without prior warning.

[2]
DECLARATION OF CONFORMITY

[3]
SPECIFICATION
The CNC Design Ltd policy of continuous improvement determines the right
to change specification without notice.
Dimensions of base plate (L x W)
870mm x 400mm
Weight
38Kg
Maximum feeder travel
Approx. 100mm(35mm Between
Bobbin plate & Tailstock)
Maximum Stepper motor RPM
1200RPM Recommended MAX
Maximum bobbin diameter
(Height)
85mm
Wire range
0.01mm-0.3mm
Feeder max resolution
0.0005mm
WARRANTY
12 months Return to Base warranty is offered all assembled machines. This is
on a Return to Base policy which means the customer will be liable to pay for
the shipping of the faulty parts back to us and we will be liable for the cost of
replacing and shipping back to the customer.

[4]
SAFETY WARNING
Keep hands clear of moving parts during operation.
Ensure all handles are fully tightened before operating.
Make sure the power is switched off before connecting the power supply.
MAINTENANCE
The machine has been designed to be low maintenance.
Your machine has been delivered lightly greased as such to keep the machine
as clean as we can when assembling.
Please make sure to apply grease to the Ball screw and all the rails before
running the machine too hard or fast.
Any moving parts such as the feeder ball screw and the tailstock rail need to
be lightly greased periodically depending on use.
Check the tightness of all nuts and bolts.

[5]
GETTING TO KNOW YOUR COIL WINDER
1
Control Unit
7
Bobbin Plate
2
ARM MKII Controller
8
Tailstock
3
Power Supply
9
Belt tensioner
4
Safety Cover
10
Safety Cover Limit Switch
5
Feeder Assembly Positioning
Micrometer
11
Adjustable Feet
6
Feeder Assembly
1
4
3
6
10
5
2
8
7
9
11

[6]
OPERATION AND USE
Remove Machine from the crate,
remove wrapping.
There are 4 push control buttons
located at the front of the
machine.
These are from left to right:
Start, Stop, Pause and Home.
Also on top is the emergency
stop button.
There are handles for each
feeder assembly.
Use these to align each one to
their bobbin plate.

[7]
OPERATION AND USE
For Micro-adjustments use the
Micrometer attached to each
feeder assembly.
Take care when maneuvering
these along the rail as too much
force from collisions could break
the micrometer.
DO NOT overtighten the red knob
as this could cause a jam.
Connect the power supply to
your Mains supply. (Red Arrow)
Insert the USB lead into the
controller box. Then plug the
other end of the USB into
computer. (Blue Arrow)
All complete and ready to run up
the software.
GENERAL INFORMATION
A Larger document with clearer instructions is located on the memory stick
supplied.

[8]
INSTALLING SOFTWARE
Insert the enclosed USB stick into
your computer, browse to the
device and run setup.exe.
Proceed through the wizard.
Here you can select the
installation folder and choose to
install this for multiple users or a
single user.

[9]
INSTALLING SOFTWARE
After installing the software click
close.
Browse to your desktop for a new
shortcut as shown.
All finished and ready to be used
with your Coil Winder.

[10]
CONTACT DETAILS
CNC Design limited,
Unit 5S Lanvale Estate,
St. Columb Major,
Industrial Estate,
Cornwall,
TR9 6SF,
England
Telephone: [phone]
Web: http://www.ukcnc.net
Email: [email protected]
©PUBLISHED BY CNC DESIGN LTD.
No part of this publication may be reproduced, stored in a retrieval
system or transmitted in any form or by any means, electronic,
mechanical photocopying, recording or otherwise without prior
permission in writing from CNC Design Ltd.

[11]
NOTES

[12]
NOTES