CNC Workshop Miniature Scenery Conquerer III User manual

Preparation
Once you clear some table space you will need a
pair of side cutters and glue (PVA, wood glue, hobby
glue). A file or small piece of sandpaper can be used
to clean along any edges that have bur.
It’s a good idea to familiarise yourself with how the
pieces fit together before gluing.
Getting Started
I. Remove all the parts out of the board with
your cutters.
II. Go over each part again with the cutters
removing as much of the tabs as possible (this
greatly reduces the time needed with the file or
sand paper).
III. Use a file or sand paper last to completely
remove the tabs that might remain.
IV. Parts may be a very tight fit, slight trimming
or sanding of parts may be needed for ease of
assembly.
Construction
Slot the parts together as shown by the pic-
tures below, applying glue wherever there is
a connection.
Allow the model to completely dry before
painting it.
INSTRUCTIONS
Tyres
The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia
Its VERY IMPORTANT
That you read through and familiarise yourself
with the instructions (particularly the tracks)
BEFORE REMOVING PARTS FROM THE
SHEETS!!!

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia
R1
(L1)
R2
(L2)
R3
(L3)
R4
(L4)

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia
WARNING!!
This part is super fragile until firmly glued in place.
If you break it (Like I did), carefully glue each piece
in position.
When dry, I suggest using super thin super glue all-
over to reinforce the part.
R5
(L5)
R6
(L6)

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia
Once the outside track run (part R6 and
L6) is glued firmly in place and dry, I sug-
gest dripping super thin superglue over
the whole part to strengthen the assembly.
This part is super thin and
fragile. When you break it ,
don’t panic. simply glue the
pieces in position and allow
them to dry.

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia
Repeat Track assembly for opposite
side.

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia
Alternate Parts.
For with/ without sponson weapons.

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia
Note off-set of slot

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia
Note the holes are off-set
from the centre.
Centre
line
You can Chamfer these edges with a
sharp knife and / or file. The model
will look cooler for it.

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia

The exclusive copyright on the model designs are the property of CNC Workshop Ltd. © Copyright CNC Workshop Ltd., 2006. All rights reserved. Made in Australia