CNCOTE CE-03 User manual
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
Vehicle & Motorcycle & E-bike GPS Tracker
Model: CE-03
User Manual
1. Feature:
Supports GSM frequencies 850/900/1800/1900MHz.
Support Web based application tracking and mobile app tracking and SMS tracking.
SMS and GPRS TCP/UDP Communication.
Back up battery.
Voltage: 9-100V DC.
Accuracy: 10 Meter.
Internal antenna. (High Sensitive GPS)
Very samll size like a car key: 67(L)mm*38.8(W)mm*11.5(H)mm.
Low current consumption sleep mode.
Water-proof.
2. Function:
Real time tracking and history tracking playback(last 3 months)
ACC detection.
Mileage calculation.
Alert: over speed/vibration alert.
Support cut off engine and oil(option)
out off power alarm.
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
3. Widely Application:
Motorcycle E-Motorbike Car shop truck and Trucks
4. Images of CE-03:
Dimension Comparesizewithalighter
Comparesizewithcarkey
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
Back face, where to insert SIM card
5. Specification:
●GSM 850/900/1800/1900 Quad band for global world
●GPRS: CLASS12,TCP/IP
●Voltage input range:9 – 100V
●Current：3.5mA@48V
●GPS positioning time：Cold start -38S (OPEN SKY）
Hotstart-2S(OPENSKY）
●GPS positioning precision：10m（2DRMS)
●Temperature ：-20 ~ +70℃℃
●Humidity：20% - 80% RH
●Dimension：67(L)mm*38.8(W)mm*11.5(H)mm
●Weight: 31g
6. Indicating Led Light:
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
NOTE：For covert protective , the LED status will be invisible after installing the
back cover.
(1).Red Led -Power status indicator
Led status Meaning
Quick flashing Working normally (working by backup car battery ).
Slow plashing Working normally (working by battery of device)
the device will change to work by own battery
while backup battery had been cut down and it will
alarm .
Continuously in bright status Device error
(2).Blue LED-GSM status indicator
LED Status Meaning
Quick flashing Working normally ,uploading GPRS data to
platform server
Slow flashing Working normally ,receive GSM signal normally
Continuously in bright status No GSM signal
(3).Green LED- GPS status indicator
LED Status Meaning
Quick flashing Working normally , GPS Located
Continuously in bright status Searching GPS signal
7. Installation:
7.1 preparation before installation:
7.1.1, Open the packing box to check whether the type of device is correct and whether
the accessories are included ,or else please contact with your distributor.
7.1.2, To test SIM card, please install it into a normal GSM mobile and ensure it can send
and receive SMS, and enables for GPRS.
7.1.3, SIM installation, refer to below pictures.
Note：Power off before installing or removing the SIM card.
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
7.2, Notice of Installation:
To prevent theft of the Device, the device should be installed as covertly as possible.
Notice as following:
7.2.1, Avoid placing the Device close to higher power electrical devices, such as reversing
radar, anti-theft device or other vehicle communication equipment.
7.2.2, The Device should be fixed into position with cable ties or wide double-side tape.
7.2.3, Device has built-in GSM antenna and GPS antenna. During installation, please
make sure the receiving side face is up, with no metal object above the device to interfere
with GPS reception.
7.2.4, For safety , do NOT remove the fuse of device cable.
7.3, Device wiring diagram:
For Motorbike and E-motorbike For car & vehicle & trucks
7.4, Steps of installation:
7.4.1, Open the back cover ,insert a SIM card to SIM card slot .
7.4.2, Switch power button up(power on) .
7.4.3, Connect the power code with the interface of device. Now three LED lights will
lighting .Make sure the receiving side face up,without any metal object shelter.
The LED lights will flashing after 1 to 5mins. It shows working normally.
7.4.4, Close the back cover.
7.4.5, Please ask professional technical to connect wires and install to the vehicle. After
correct installation, the RED led will flashing, 1 min. Later the BLUE led will flashing too.
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
That shows installing completely.
8. Cautions of device wiring
8.1 Power code wiring:
The standard voltage is 9V-100V. Please use the power line which provided by the
manufacturer. The red line is the positive. The black line is the negative. The negative
should earth alone or link iron during installing. Do not connect it to other ground wire. And
please make sure the device is powered on status. (Power button on down position)
Red Led light will flashing while device installed correctly, GSM blue led light and GPS
Green led light will flashing around 1 minutes later after getting signal.
8.2, Usage of Device
Our GPS Tracker is used for motorcycle, electric-bike two wheels, electric-bike three
wheels. As well as for car ,truck etc four wheels vehicle.
9. Message commends
User can set different kinds of function commands via sending message, including check
position, cut engine, etc., below commands and punctuation marks must be putted under
English status. All commands will get auto replies according to the message sent.
Note device with initial password 6666
N
O. Features Commands
Replies from device
Remarks
1
Add administrator
No 1
#6666#AAD#
1#Cell No# ADD admin account 1 ok!
2
Add administrator
No 2
#6666#AAD#
2#Cell No# ADD admin account 2 ok!
For example：
#6666#AAD#1#15988888888#
Means administrator1 number is ：
15988888888，can add 2
administrator total
3
Delete
Administrator No 1
#6666#DAD#
1# Delete admin account 1 OK!
4
Delete
Administrator No 2
#6666#DAD#
2# Delete admin account 2 OK!
For example：#6666#DAD#1# for
delet the administrator
1 ;#6666#DAD#2# for delet the
administrator 2
5 Cut engine #6666#CF#
Fuel cut has already been
completed,OK!
For example：#6666#CF# ，only
apply for administrator
6 Restore engine #6666#OF#
Open fuel has already been
completed,OK!
For example：#6666#OF# ，Start
engine only apply for administrator.
7
Setting time
distance in moving
status
#6666#SMT#
sendconds#
Set movement upload
time,OK!
#6666#SMT#30# For example：
#6666#SMT#10#，Here the unit is
senconds 10 to 200s
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
8
Setting time
distance in steady
status
#6666#SST#
minutes# #6666#sst#3#ok!
For example：#6666#SST#3#，Here
the unit is minutes
9
Setting sleep
mode time
#6666#SLEE
P#TIME#
For example ：#6666#SLEEP#10#
this mean setting sleep mode and
every 10 minutes device will exit
sleep mode and send a data to
server , time rang:1-99999 ，
0=disable sleep mode
10
Active vibration
alarm
#6666#SSA#l
evels# Set alarm level, OK!
For example：#6666#SSA#1#，Here
Levels, 1: most fexible 2: standard
level 3. lowest level .
11
Cancel vibration
alarm #6666#CSA# Close vibration Alarm, OK!
For example：#6666#CSA#，cancel
vibration alarm
12 SMS Alarm
#6666#SMSA
#1#
1= allow sms alarm 0=Disable sms
alarm, For example:
#6666#SMSA#1#
13 Call Alarm
#6666#CALL
A#1#
1= allow call alarm 0=Disable call
alarm
14 Re-start device
#6666#Reset
# Start Reset System, OK!
For example：#6666#RESET#，The
device will restart after 8~18 mins.
Device will not reply message to
administrator again .
15 Set APN #0613#sapn#apn name#user#password###
For example：
#6666#sapn#CMNET##### if user
name and password are blank, Or
#6666#sapn#CMNET#AA#123456#
##
,# can not be missed
Simply Commands: In order to make the steps easy, below you can find our simply
commands, the function is same as per above detailed commands.
Remarks: SMS must be text under English status.
Features Simple commands Remarks: Authority
Getting Location
of longitude and
latitude 1234
Reply with google
links of longitude
and latitude Anybody
DY
Engine cut RELAY,1# Cut off the engine
Only
administrator
KY
Restore engine RELAY,0# Restore the engine
Only
administrator
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
CS
PARAM#
View information STATUS#
Checking IMEI,IP，
Etc, Anybody
Re-start CQ Re-start the device Anybody
Vibration alarm specifications:
If you need vibration alarm, please follow below instructions:
1）Add admin number: please use your mobile phone to send a SMS to the device
according to the 1st command as above commands list(make sure to text the SMS under
English status). After add your number as administrator, device will reply you a SMS with
OKorfailed.
2）Setting vibrate alert level: text a SMS to active vibration alarm and send to the
device(make sure to text the SMS under English status), and set the vibration alert level,
detailed please refer the 10th command as above commands list.
3）After finished above 2 steps, vibration alarm had been actived. As long as the car
stopped for more than 1minute, if somebody gets in touch with the car and didnt turn on
the ACC in 10seconds(ACC=0), the device will send SMS and call the administrator. If the
ACC was turned on in 10seconds, the device will judge it as the car owner himself and will
not alert the car owner. This is for not sending wrong vibration alert, active and close the
vibration alarm smartly.
Sleeping Mode with power saving Specifications:
The sleeping mode had been activated and defaulted inside the device in the factory：After
the car has switched off more than 5 minutes, the device will shut off all the led lights,
turn off GPS module and goes to sleeping mode to save the power of the vehicle’s battery.
There are 2 methods to exit the sleeping mode: 1)，Switch on the ACC，at this time , the
green ACC cable is high level up, this will lead device exit sleeping mode.。If ACC is
always on high level up,(means ACC is always on) the device will not goes to sleeping
mode. 2)，Shake the device to make it exit from sleeping mode.
During the first time testing, it is better to connect the ACC wire to high level up to locate
the GPS signal fast in the opening area as well as to avoid the device goes to sleeping
mode and could not locate the GPS after 5 minutes. (note: please do not test in room as
no GPS signal inside room). If client need to turn off the sleeping mode, please send SMS
to the device #6666#SLEEP#0# to close this function.
10. Trouble shooting
10.1, After installing it in the first time, if device can not get connected with platform server,
at this time it is “logged off” status in platform. Please check the installation of device:
1) Check whether the connection of power-line is correct, please do not connect it with
the car control line.
SHENZHEN CNCOTE TECHNOLOGY CO., LTD
Website: www.cncote.com Attn: Jack Foo,
2) Check whether SIM card is installed correctly, please refer to the installation manual;
3) Check whether the power switch is toggled to “ON”, the switch is in the left of the SIM
card’s slot.
4) Whether ACC ignition cable is connected, please turn on the ACC with key after it is
connected.
5) Check the LEDs’ status. In normal working status, the red LED is in solid bright or
flashing; green LED and blue LED are both in solid bright.
6) Check whether GPS is located, if not, please drive to the open areas for positioning.
10.2, If it is “offline” status in platform:
First of all, check the three LED’s status. If it is not convenient to check that，please check
the SIM card status :
1) Call the SIM card number of the device to check whether you can get through;
2) Check whether the vehicle is in no GSM area, such as basement;
3) Check the GSM/GPS disconnection area, whether it is all disconnected or few of
them disconnected, to make sure whether it is the fault of operator’s internet.
4) Check whether your SIM card charge is overdue;
5) Check whether the SIM card supports GPRS;
6) Check the parameter setup, whether the device IMEI number, GPRS sending interval
is correct.
10.3, If the device’ GPS function is normal, but can not locate for a long time, please
check whether the installation setup of device is correct:
1) Please make sure the GPS antenna face is up;
2) Please make sure there is no electromagnetic wave- absorbent object (metal) above
the device, especially the thermal-protective coating on the windshield, it may affect the
GPS reception of the device;
10.4, If GPS can not receive the signals normally (there is high building around to interfere
with GPS reception), please drive to the open areas for positioning. Generally, it needs
1-2 minutes to receive the first coordinates.
10.5, If GSM can not receive the signals normally, please check whether SIM card is
installed correctly or there is no GSM signal at the location you are, such as basement
parking, please drive to a place covered by GSM signal reception.
10.6, When cell phone with special number receives tele- cutoff alarm SMS, please make
sure whether it is illegal wire cutoff, or the FUSE on power line is blown. If the FUSE in it is
blown, please contact your distributor to exchange with the same model FUSE, after the
internal trouble is shoot, it can be power on to work again.
Table of contents
Other CNCOTE GPS manuals
