Co2meter CM-1029 User manual

Industrial Siren
Strobe
Installation Manual
*Replace "x" with the first letter of the lens color, amber, blue, clear, or red.
The Industrial Siren Strobe is a multi-purpose device: siren, speaker, and an optional strobe. It can
serve as a regular siren, but also has an audio input that can be used to play audio or broadcast
messages. Audio input will override the siren for the duration of the broadcast. The strobe light is
available with amber, blue, clear, orred lenses.
•9~15 VDC and low current draw
•120dB Warble-tone siren
•25W Speaker for audio or broadcast system input (broadcast will interrupt the siren)
•Built-in tamper alarm output
•Weatherproof for outdoor/indoor use, IP65
•Mount directly to wall or to most common back boxes
In addition to the above, the strobe siren adds:
•Bright LED strobe light
•Strobe can be triggered separately from siren
•Strobe available in amber, blue, clear, or red

Industrial Strobe Siren
2
Parts List
1x
Siren/Strobe
4x
Mounting screws
4x
Plastic wall anchors
1x
Back removal tool
1x
Manual
Specifications
Model
CM-1029
Type
Siren
Operating voltage
9~15 VDC
Current
draw
Siren
680mA@12VDC
Strobe
N/A
190mA@12VDC
Both
N/A
870mA@12VDC
Siren volume
120dB
Speaker rating
25W Peak
Strobe flash rate
N/A
100 per minute
Tamper output
100mA@30 VAC/VDC
IP Rating
IP65
Operating humidity
0~95%
Operating temperature
-4°~131° F (-20°~55° C)
Housing
White polycarbonate plastic
Dimensions
6
1
/
8
"x4
15
/
16
"x4
1
/
2
" (155x126x115 mm)
Weight
1-lb 13-oz (812g)
*Replace "x" with the first letter of the desired LED lens color – amber, blue, clear, or red.
Overview
Siren/Strobe
41/2" (115mm)
415/16"
(126mm)
Siren
7"
(178mm)
61/8" (155mm)
61/8" (155mm) 41/2" (115mm)

3
Installation
1. Determine the desired location and
installation—surface or to a back box.
2. Remove the two screws from the two
tabs that attach the mounting base to
the main unit (See Fig. 1).
3. Squeeze the included base removal tool
and insert through the wiring access
hole in the back of the unit. Release and
pull carefully until the mounting base is
removed from the unit.
4. Remove the base removal tool and turn
the mounting base over to view the
wiring terminals (see Fig. 2)
5. Thread the wires (up to 8 wires,
depending on installation, see "Sample
Applications" on pg. 4) through the
center hole in the base and install the
baseto the wall/back box using the four
mounting holes in the base, oriented so
that the engraved arrow is pointing up.
Be careful not to use the hole for the
tamper switch (see Fig. 2).
NOTE: For non-standard boxes, drill out
any other holes engraved in the
oval indentations on the
mounting base as needed.
6. Connect the wires for the desired
installation to the terminals on the
mounting base as shown in Fig. 3 and
referring to the sample applications on
pg. 4. Note that audio input requires
power to the P.A. (+) terminal.
7. Carefully slide the main unit onto the
base, ensuring the correct orientation
(note the notch and the arrows) and
ensuring the terminal plugs are correctly
engaged (see Fig. 1).
8. Attach the main unit to the base using
the two screws removed in step 2.
Fig. 1
Tamper switch
Orientation
alignment notch
Tamper
switch
hole
Mounting base removal tool
Terminal blocks are on reverse
Fig. 2
Mounting holes
Mounting holes Tamper
switch
hole
STROBE (+)
SIREN (+)
GND
P.A. (+)
AUDIO (+)
AUDIO (–)
TAMPER
TAMPER
Wiring
access
hole
Orientation
alignment
notch
Fig. 3
Terminal blocks
STROBE (+)
SIREN (+)
GND
P.A. (+)
AUDIO (+)
AUDIO (–)
TAMPER
TAMPER

Sample Applications
NOTE: The audio broadcast will override and interrupt the siren for the duration of the broadcast.
STROBE (+)
SIREN (+)
GND
P.A. (+)
(+)
(–)
(+)
AUDIO (+)
AUDIO (–)
TAMPER
TAMPER
12VDC
Power
Supply (–)
Triggering both siren and strobe* together
(also showing audio input)
Alarm
System
Audio or
Broadcast
System
Strobe*
Triggering
Device
AUDIO (+)
AUDIO (–)
TAMPER
TAMPER
STROBE (+)
SIREN (+)
GND
P.A. (+)
(+)
(–)
(+)
(+)
(–)
12VDC
Power
Supply (–)
Siren and strobe* triggered by separate devices
(also showing audio input)
Alarm
System
Audio or
Broadcast
System
Siren
Triggering
Device
Strobe*
Triggering
Device
Call 1.877.678.4259
Email [email protected]mSale
S[email protected]
Web CO2Meter.com
Let’s Get Social —
@CO2Meter on: