Coaster 203501Q User manual

QUEEN SIZE BED
203501Q (B1&B2)
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com
R
PAGE 1 OF 4 REVISION 0 : 05/16/2014
REVISION 1 : 05/27/2014

ITEM : 203501Q (B1&B2)
www.coastercompany.com
HARDWARE IDENTIFICATION
1.Remove hardware from box and sort by size.
2.Please check to see that all hardware and parts are present prior to start of assembly.
3.Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
1.Don't attempt to repair or modify parts that are broken of defective. Please contact the store
2.This product is for home use only and not intended for commercial establishment.
Warning!
immediately.
PAGE 2 OF 4
SMALL ALLEN WRENCH
BIG ALLEN WRENCH
ASSEMBLY TIPS:
ASSEMBLY INSTRUCTIONS
PARTS IDENTIFICATION
B1 (BOX 1)
A
B
1PC
1PC
Z - B1 (BOX 1)-Hardware is located in 203501Q(B1)
F BED RAIL 2PCS
203501Q (B1)
*FROM BOX 1
HEADBOARD COMPLETE
5
6PCS
6
4PCS7
8 1PC
1PC
BOLT
C1PC
B2 (BOX 2)
DBED SLAT 4PCS
EBED SLAT SUPPORT
WITH LEVELER 4PCS
G
H
HB
FOOTBOARD LEG
FOOTBOARD PANEL
2PCS
1PC
1PC
8PCS
9
LONG FLAT HEAD SCREW
SHORT FLAT HEAD SCREW
HEADBOARD PANEL
RIGHT
HEADBOARD LEG
LEFT
HEADBOARD LEG
6PCS
1BOLT
1PC2 SMALL ALLEN WRENCH
6PCS3 FLAT WASHER
6PCS4 LOCK WASHER
Z - B2 (BOX 2)-Hardware is located in 203501Q(B2)

PAGE 3 OF 4
ASSEMBLY INSTRUCTIONS
203501Q (B1) - BOX 1
STEP 2
Align and fasten right (B) & left (C) headboard legs to
headboard panel (A) using bolt(1), lock washer (4)& flat
washer (3) ,then tighten with Allen wrench(2).
STEP 1
Place headboard panel (A) facing downward on soft
surface,and install right (B) & left (C) headboard legs to
headboard panel (A) as per diagram shown.
**Please take note the marking on the leg **
**BACK VIEW
203501Q (B1 & B2) - BOX 1 & BOX 2
STEP 3
Align and fasten footboard leg (G) to footboard panel (H) using long flat head screw (6) and tighten with screw
driver (Not included).
IF PURCHASE HEADBOARD ONLY, SKIP BELOW STEPS
H
6
G
ITEM : 203501Q (B1&B2)
2
1
4
3
A
C
STICKER LEFT
STICKER RIGHT
A
C
B
B
**BACK VIEW
www.coastercompany.com
PLEASE REMOVE THE
PROTECTIVE FILM
BEFORE ASSEMBLY

PAGE 4 OF 4
ASSEMBLY INSTRUCTIONS
STEP 4
E
STEP 5
D
8
7
STEP 6
Loosen the bolt.
Align & hook bed rail (F) to headboard (HB) & footboard (H).
Align and fasten bed slat support with
leveler (E) to bed slat (D) using bolt (7) & tighten
with small Allen wrench (8).
6.1) Fully tighten all the bolts at step 4 with big Allen wrench (9).
6.2) Align & fasten bed slat (D) to bed rail (F) using short flat head
screw (5) & tighten with screw driver (NOT INCLUDED).
Then adjust leveler to touch the floor.
H
F
HB
9D5
ITEM : 203501Q (B1&B2)
www.coastercompany.com
6.1
6.2