Coaster 306020QB1 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
306020Q(B1&B2)
Queen Bed
COASTERFURNITURE.COM
REVISION 0 : 05/22/2023
PAGE 1 OF 5

PAGE 2 OF 5
ASSEMBLY INSTRUCTIONS
ITEM: 306020Q(B1&B2)
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
WARNING!
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME 30 MINUTES
PARTS IDENTIFICATION
A HEADBOARD PANEL
COASTERFURNITURE.COM
E BED RAIL
C FOOTBOARD PANEL
1PC
F CENTER RAIL
H CENTER RAIL SUPPORT
2PCS
1PC
2PCS
3PCS
B HEADBOARD LEG
1PC
G ROLL SLAT
(13PCS)
1SET
B1 (BOX1)
B2 (BOX2)
2PCSD FOOTBOARD LEG
HB 306020Q(B1)
FROM BOX1
HEADBOARD
COMPLETE
FB 306020Q(B2)
FROM BOX2
HEADBOARD
COMPLETE
1PC 1PC
WITH LEVELER

HARDWARE IDENTIFICATION
4PCS1 BOLT
(Ø5/16" x 50mm - RBW)
2 FLAT WASHER
(Ø5/16"-RBW)
3 LOCK WASHER
(Ø5/16"-RBW)
4PCS
4PCS 4 ALLEN WRENCH
(5mm - RBW)
1PC
PAGE 3 OF 5
ASSEMBLY INSTRUCTIONS
ITEM: 306020Q(B1&B2)
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
WARNING!
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME 30 MINUTES
COASTERFURNITURE.COM
Z-B1 (BOX1) - HARDWARE PACK IS LOCATED IN 306020Q(B1)
12 PAN HEAD SCREW
(M4 x 35mm - RBW)
8PCS
Z-B2 (BOX2) - HARDWARE PACK IS LOCATED IN 306020Q(B2)
9 LONG BOLT
(Ø5/16" x 100mm - RBW)
8PCS
4PCS5 SHORT BOLT
(Ø5/16"x50mm-RBW)
6 FLAT WASHER
(Ø5/16" - RBW)
7 LOCK WASHER
(Ø5/16" - RBW)
12PCS
12PCS
11 WRENCH
(12mm - RBW)
8PCS
8 ALLEN WRENCH
(5mm - RBW)
1PC
10 HEX NUT
(Ø5/16" - RBW)
1PC
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.

PAGE 4 OF 5
ASSEMBLY INSTRUCTIONS
ITEM: 306020Q(B1&B2)
COASTERFURNITURE.COM
STEP 1
A
C
B
D
2
3
1
4
9
1.3
1.1
6
7
5
8
1.2
STEP 2
HB
E
E
FB
610 11
9
7

PAGE 5 OF 5
ASSEMBLY INSTRUCTIONS
ITEM: 306020Q(B1&B2)
COASTERFURNITURE.COM
COMPLETE
G
H
F
STEP 3
STEP 5
STEP 4
12