Cobra Fi2000 User manual

®23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. [phone]
www.fi2000r.com
04/11
1
*Cobra® recommends you always wear a helmet while riding. Please never operate your motorcycle while under
the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.
Items Supplied >
1 –Fi2000AT Fuel Injection Module
5 –Zip Ties 6”
1 –Velcro Stripe
Application(s) >
HARLEY SOFTAIL 2007
Instruction Manual >
ATTENTION: All 2007 Harley SOFTAIL models manufactured before NOVEMBER 1, 2006 require
an ENGINE CONTROL MODULE CALIBRATION update from a Harley Davidson Dealer; please
reference Harley Davidson SERVICE BULLETIN M-1186. This Fi2000 is meant to function on all
2007 SOFTAIL models with this update and all 2007 SOFTAIL models manufactured after this date
which should already have this update installed, check with your local dealer for verification.
Read all instructions carefully and completely before installing your new Fi2000AT module. It is
recommended that a qualified mechanic or technician install this product.
1. Remove the seat and air cleaner assembly, remove both front and rear gas tank mounting bolts. Prop the rear
of the gas tank up approximately 2”.
2. Locate the factory connector on each fuel injector. Depress the clip on the connector and pull the connector
free and move it out of the way. Note: A pair of needle nose pliers and a long flat blade screwdriver helps with
this job. If you need additional access to the fuel injector connectors, you can remove the Idle Air solenoid by
removing the two 5/16’’ bolts holding it on and loosening the Torx #20 screw on throttle cable bracket. Make
sure to use thread-locking compound when refitting the two 5/16” bolts and correctly position the o-ring when
reattaching.
3. Lay the Fi2000 module in the area underneath the seat, do not attach it to the motorcycle, route the injector wire
harness forward up the right side of the frame backbone, see Figure 1. Route the forward set of connectors
under the upper motor mount.
4. Attach one pair of Fi2000 module’s injector plugs to the front injector. Take the original female H.D. connector
and insert the corresponding Fi2000 male connector into it, refer to Figure 2.
5. Attach the Fi2000 module’s remaining female injector plug onto the rear injector. Then take the original female
H.D. connector and insert the corresponding male Fi2000 connector, into it, refer to Figure 2.
6. It is now time to install the oxygen sensor harnesses. Remove the battery for access to the area underneath it
and to aid in harness installation. To help installation, disconnect square connector at right rear corner of battery
to help installation of O2sensor harnesses, see Figure 3. Route the two O2sensor harnesses down between the
main harnesses going to the fuse box and the right rear corner of the frame in the battery area. The longer
harness continues down past the rear of the transmission and the shorter harness comes forward under the
bottom of the oil tank until it is visible in the cut out area where the battery sits. Unplug the factory O2sensor
connection and plug in the corresponding male and female connectors.
7. Now route the longer harness up the right side of the frame rail. Following the factory harness and zip tie it to the
harness in 3 locations.
8. Remove the 2 Allen bolts that secure the voltage regulator bracket to the block, and remove the rectangular
cover over the top of this bracket. Ease the voltage regulator forward just enough to access the front O2
connector. Unplug the connector and then plug the Fi2000 female connector into the original HD male
connector. Replace this connection into the voltage regulator bracket and re-assemble onto the bike, making
sure the Fi2000 wire exits the top of the cover just like the original wire went in.
692-1607AT
Page 1 of 3
DOCUMENT NO. 0017 REV. A

®23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. [phone]
www.fi2000r.com
04/11
2
Instruction Manual >
692-1607AT
Page 2 of 3
9. Now plug the other Fi2000 connector into the oxygen sensor wire and zip tie this connection to the left frame
tube in a location that will not allow the wires to touch the exhaust pipe, Figure 4
10. Reinstall the battery, attach the black wire to the negative post of the battery, see Figure 1.
11. Verify the wire connections; turn on the ignition and watch the Fi2000 LED logo, confirm that the LED blinks
several times then turns off. If you do not see any blinking, it may be necessary to wait for the alarm to reset (if
applicable) and try again. Also confirm the side stand is up, bike is in neutral, clutch is in and handle bar engine
switch is set to run (where applicable). Start the bike and the Fi2000 logo should remain solid red, which
confirm the unit is fully functioning. If it flashes while the bike is running, turn off the bike and recheck that all
harness connections (injectors, ground wire, and O2 sensors when applicable) have been properly made. Re-
verify by turning ignition on while watching for flashing LED, prior to starting. Start and confirm LED remains ON
solid red. NOTE: Make sure ignition is turned off before attempting to change any Fi2000 harness connections.
12. Remove the backing from the Velcro and attach the Fi2000 as shown in Figure 1.
13. Re-install the fuel tank, seat and air cleaner assembly.
DOCUMENT NO. 0018 REV. A

®23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. [phone]
www.fi2000r.com
04/11
3
Instruction Manual >
692-1607AT
Page 2 of 3
DOCUMENT NO. 0018 REV. A
FIGURE 1
Fi2000 MODULE
FRONT
ECU
CONNECTOR
GROUND WIRE
CONNECTED TO
NEGATIVE
BATTERY
TERMINAL
O2SENSOR
HARNESSES
ROUTED
FROM HERE
TO UNDER
BATTERY
FEED O2
HARNESSES
BETWEEN FRAME
RAIL AND STOCK
HARNESS
FIGURE 3 FIGURE 4
FI2000
HARNESS
WITH O2
SENSOR
CONNECTO
R
STOCK
HARNESS
WITH FI2000
FEMALE
HARNESS
CONNECTOR
BATTERY
TRAY
FIGURE 2
FRONT FEMALE Fi2000
INJECTOR CONNECTOR
ON FRONT INJECTOR
ORIGINAL FRONT FEMALE
H.D. INJECTOR
CONNECTOR WITH MALE
Fi2000 INJECTOR
CONNECTOR
REAR FEMALE Fi2000
INJECTOR CONNECTOR
ON REAR INJECTOR
ORIGINAL REAR H.D.
INJECTOR CONNECTOR
WITH MALE Fi2000
CONNECTOR
NOTE: For California riders we offer Air Resources Board approved Fi2000R ARB units. (ARB E.O. No. D-633-1). All
other Fi2000 models are not legal for street use in California.