Cobra CPP 7500 User manual

CPP 7500
User Manual
Portable Power - Anytime, Anywhere!
Thank for purchasing the Cobra CPP 7500 JumPack™jump
starter portable PowerPack. Before using this product, please
read these instructions carefully to learn about the features
and capabilities of the JumPack and how you can get the
best out of it.
Note: Please charge your CPP 7500 JumPack completely
prior to using it for the rst time.
©2014 Cobra Electronics Corp. Part No. 480-936-P Printed in China Version B
Charge the JumPack fully prior to use.
WARNING: Keep the unit clear of re and water.
WARNING: Shock Hazard. Keep away from children. Do not
insert foreign objects into the jumper cables port/jack, the USB
output port, or the DC input jack. Do not expose this product to
water, rain, snow, condensation, or spray. Do not open the
JumPack to replace the internal battery. No user replaceable
parts are inside the JumPack.
WARNING: Explosion Hazard. Do not use this product where
there are ammable fumes or gases, such as in the bilge of a
gasoline-powered boat, or near propane tanks. Do not use this
product in an enclosure containing automotive-type lead-acid
batteries.
The jump start cable clamps must be connected positive to
positive (red clip to battery (+)) and negative to negative (black
clip to battery (-)). A reverse polarity connection (positive to
negative) may cause damage to the JumPack and/or create a
sparking/explosion hazard.
WARNING: Fire Hazard
Do not crush or puncture the JumPack. Never allow the jump start
cables’ red and black clamps’ metal contacts to touch each other or
another common metal conductor. This could cause damage to the
unit and/or create a re hazard. Always disconnect the jump start
cables from the JumPack after each use and store separately. The
jump start feature is designed for short term operation only.
Turn the ignition key for no more than 3 seconds at a time.
Operating the jump start feature for more than 3 seconds may
cause damage to the unit. Allow the JumPack to cool down for at
least 1 minute after each jump start attempt.
IMPORTANT SAFETY INSTRUCTIONS Caution: Operating temperature
Do not expose the JumPack to temperatures over +113° F (+45° C) or
under -14° F (-10° C). Using the JumPack at high or low temperatures
may reduce the internal battery capacity and shorten the battery life.
Note: In extreme cold weather conditions, please bring the JumPack
indoors for best results.
Precautions when working with batteries
WARNING: Explosion and re hazard
1.
Follow all instructions published by the battery manufacturer and the
manufacturer of the equipment in which the battery is installed.
2. Make sure the area around the battery is well-ventilated.
3. Never smoke or allow a spark or ame in the vicinity of the engine
or batteries.
4. Be careful not to drop a metal object on the battery or allow a
metal tool to simultaneously touch the positive and negative cable
ends or battery terminals.
5. Remove personal metal items such as rings, bracelets, necklaces,
and watches when working with batteries. Batteries produce a
short-circuit current high enough to weld a ring or other similar
objects to metal, causing a severe burn.
6. If you need to remove a battery, always remove the negative
terminal from the battery rst. Make sure all accessories are
off so you don’t cause an arc.
7. Someone should be within range of your voice, or close enough to
come to your aid when you work near batteries.
8.
Have plenty of fresh water, soap and a supply of baking soda on
hand in the area of the batteries in case of contact with battery acid.
Baking soda neutralizes lead acid battery electrolyte.
9. The JumPack is supplied with a rechargeable Li-Cobalt battery.
This battery is self-contained and not consumer replaceable. Battery
must be disposed of properly when it no longer holds a charge. Proper
charging practices will increase the life of the batteries.
For information
on battery recycling call toll free 800-822-8837.
Product:
Jumper cable with clamps
Battery Status Indicator LEDs
Jump Starter Cable Input
12V DC Charge Input
USB 5V/2.1 Amp Output
LED Flashlight/Strobe
Light/ S.O.S Light
Power/Flashlight/Battery
Capacity Button
Home adaptor Car adaptor
Recharging the JumPack:
The CPP 7500 JumPack can be recharged with the supplied 120V AC
wall charger connected to an AC home outlet or with the supplied 13.8V
DC vehicle charger.
When the CPP 7500 is charging; the LEDs will show the current battery
life. The last LED that is lit will blink to show that the JumPack is charging.
When the JumPack is fully charged the LEDs will turn off automatically.
For best battery performance the JumPack should be fully recharged
every 3 months.
Operation:
Check Battery Capacity:
To check the battery capacity of the JumPack press the
Power/Flashlight button on the top of the unit with no device
connected. The blue LEDs will show the remaining battery capacity:
1LED on: 10%-40% charge
2LEDs on: 40%-65% charge
3LEDs on: 65%-85% charge
4LEDs on: 85%-100% charge
Note: When charging a device the number of lit LEDs may
decrease while the JumPack is in use. The battery capacity
indicator cannot accurately measure the capacity during rapid
charging. To conrm the real battery capacity, disconnect the
device being charged and press the power/ashlight/capacity button.
Battery Status Indicator LEDs
.1. .2. .3. .4.
CPP7500_MANL.indd 1 2/12/14 10:59 AM

Product Specication:
• Li-Cobalt rechargeable battery: 3.7V/7500mAh
• Size: 5.03” x 2.87” x 0.98”
(128mm x 73mm x 25mm)
• Weight: 10.58 oz. (300g.)
• Recharge time: 3 hours
• Starting/Peak Current: 200 Amps/400 Amps
• USB Output: 2.1 Amps
.5.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However,there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician
for help.
WARNING: Any modications made to this device that are not expressly
approved by party responsible for compliance could void the user’s authority
to operate this device.
Cobra®and the snake design are registered trademarks of
Cobra Electronics Corporation, USA.
Cobra Electronics Corporation™ is a trademark of Cobra
Electronics Corporation, USA.
PROPOSITION 65 WARNING:This product contains a chemical known to the
State of California to cause cancer and birth defects or other reproductive harm.
.6.
Limited 1-Year Warranty:
For Products Purchased in the U.S.A.
Cobra Electronics Corporation warrants that its Cobra CPP 7500 JumPack
USB Charger, and the component parts thereof, will be free of defects in
workmanship and materials for a period of one year from the date of rst
consumer purchase. This warranty may be enforced by the rst consumer
purchaser, provided that the product is utilized within the U.S.A.
Cobra will, without charge, repair or replace, at its option, defective USB
charger, products or component parts upon delivery to the Cobra Factory
Service Department, accompanied by proof of the date of rst consumer
purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for
warranty service, but the return charges will be at Cobra’s expense,
if the product is repaired, this warranty gives you specic rights, and
you may also have other rights which vary from state to state.
Exclusions: This limited warranty does not apply:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product, or as a result of
unauthorized alterations or repairs.
3. If the serial number has been altered, defaced or removed.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and tness
for a particular purpose are limited in duration to the length of this warranty.
Cobra shall not be liable for any incidental, consequential or other
damages; including, without limitation, damages resulting from loss of use
or cost of installation.
Some states do not allow limitations on how long an implied warranty lasts
and/or do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you.
.9.
Product Service:
For any questions about operating or installing this new Cobra product,
or if parts are missing…PLEASE CALL COBRA FIRST…do not return
this product to the store. See customer assistance on reverse side of this
sheet. If this product should require factory service, please call Cobra
before sending the product. This will ensure the fastest turn-around time
on any repair. If Cobra asks that the product be sent to its factory, the
following must be furnished to have the product serviced and returned:
1. For Warranty Repair include some form of proof-of-purchase, such
as a mechanical reproduction or carbon of a sales receipt. Make sure
the date of purchase and product model number are clearly readable.
If the originals are sent, they cannot be returned;
2. Send the entire product;
3. Enclose a description of what is happening with the product. Include
a typed or clearly printed name and address of where
the product is to be returned, with phone number (required
for shipment);
4. Pack product securely to prevent damage in transit. If possible,
use the original packing material;
5.
Ship prepaid and insured by way of a traceable carrier such as United
Parcel Service (UPS) or Priority Mail with delivery conrmation to avoid
loss in transit to: Cobra Factory Service, Cobra Electronics Corporation,
6500 West Cortland Street, Chicago, Illinois 60707 U.S.A.;
6. If the product is in warranty, upon receipt of the product it will either
be repaired or exchanged depending on the model.
Please allow approximately 3 – 4 weeks before contacting Cobra for
status. If the product is out of warranty, a letter will automatically be
sent with information as to the repair charge or replacement charge.
For any questions, please call 773-889-3087 for assistance or visit us
online at www.cobra.com.
FCC Statement:
• 7500mAh Lithium Cobalt rechargeable battery.
• 200 Amp Starting Current / 400 Amp Peak Current.
• 5V/2.1 Amp USB Output for rapid charging of portable devices.
• High Intensity work/Strobe/S.O.S LED light.
• Rechargeable by 120V AC wall adapter or 13.8 V DC car adapter.
Product Features:
Starting a Vehicle:
1. Make sure the JumPack is fully charged.
2. Turn off all the accessories on the vehicle.
3. Disconnect the battery cables from the JumPack.
4. Connect the RED clamp to the POSITIVE post of the battery.
5. Connect the BLACK clamp to the NEGATIVE post of the battery.
6. Connect the battery cables into the JumPack cables port/jack.
Be sure that the plug is rmly pressed into the JumPack.
7. Turn the ignition key to start the vehicle for 3 seconds only.
If the engine starts;
8. Disconnect the cables from the battery from the JumPack
then from the battery posts.
9. Leave the engine running for a few minutes before turning
the ignition off.
10. If the vehicle does not start on the rst try, wait for
1 minute before trying to start the vehicle again.
Charging a 5V USB Device:
To charge a 5V USB device, connect the devices’ cable to the JumPack’s
USB output. The JumPACK will turn on, and start charging the device
automatically. The blue LEDs will indicate that the device is charging.
LED Flashlight:
Press the Power/Flashlight/Battery capacity button for 3 seconds to turn
on the LED ashlight. There are 4 ashlight modes: steady, strobe,
S.O.S. and Off.
.7. .8.
START
CPP7500_MANL.indd 2 2/12/14 11:00 AM