Code Blue CB 2 Series Service manual

800.205.7186 •www.codeblue.com
Administrator Guide
CB 2 Series
Installation | Configuration | Operation | Troubleshooting

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 2 of 63
CB 2 Series
Administrator Guide
WARNING
ONLY QUALIFIED PERSONNEL SHOULD INSTALL THESE UNITS. THE INSTALLATION
SHOULD CONFORM TO ALL LOCAL CODES. IN SOME COUNTRIES, A CERTIFIED ELECTRI-
CIAN MAY BE REQUIRED.
NOTICE TO USERS
Copyright © Code Blue Corporation. All rights reserved. This guide or software described herein, in
whole or part, shall not be reproduced, translated or reduced to any machine-readable form without
prior written approval from Code Blue Corporation.
CODE BLUE CORPORATION PROVIDES NO WARRANTY WITH REGARD TO THIS GUIDE, THE
SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DIS-
CLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICU-
LAR PURPOSE WITH REGARD TO THIS GUIDE, THE SOFTWARE OR SUCH OTHER INFORMA-
TION. IN NO EVENT SHALL CODE BLUE CORPORATION BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR
OTHERWISE, ARISING OUT OF OR IN CONNECTIONS WITH THIS GUIDE, THE SOFTWARE
OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.
Code Blue Corporation reserves the right to make any modications to this guide or the information
contained herein at any time without notice. The software described herein may also be governed
by the terms of a separate user license agreement.
Code Blue®is a registered trademark of Code Blue Corporation.

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 3 of 63
CB 2 Series
Administrator Guide
Table of Contents
(NOTE: Phone programming instructions can be found in the IP5000 and IA4100 Guides.)
Section Page
2 Introduction.................................................................................... 5
3 Getting Started............................................................................... 6
4 Spare Parts..................................................................................... 7
5 Power Requirements...................................................................... 9
6 Legacy Power Requirements.........................................................12
7 Software Conguration..................................................................14
8 CB 2-a Exploded View....................................................................15
9 CB 2-e Exploded View....................................................................16
10 Legacy CB 2-e Low Voltage Exploded View.................................17
11 Legacy CB 2-e High Voltage Exploded View................................18
12 CB 2-s Low Voltage Exploded View...............................................19
13 CB 2-s High Voltage Exploded View..............................................20
14 How to Replace LED Light Connectors........................................21
15 CB 2-a Installation Instructions.....................................................23
16 CB 2-e Installation Instructions.....................................................26
17 Legacy CB 2-e Installation Instructions........................................29
18 Legacy CB 2-e with Public Address Installation Instructions....32
19 Legacy CB 2-e with AED Housing Installation Instructions.......35
20 CB 2-s Installation Instructions.....................................................38
21 Pole Mount Bracket Installation Instructions...............................41
22 AED Access and Maintenance Guide............................................42
23 CB 2 Series Remote Mount Beacon/Strobe Installation..............43
24 S-1000/S-1050/S-2000 Installation Instructions............................44
25 CB 2-a Standard Wiring Diagram...................................................46
26 CB 2-a PoE Diagram.......................................................................47
27 Legacy CB 2-a Standard Wiring Diagram (prior to 2020)....................48
28 CB 2-e Standard Wiring Diagram..................................................49
29 CB 2-e PoE Diagram.......................................................................50
30 CB 2-e Standard Wiring Diagram (2015-2020) (with Triad Transformer)........51
31 Legacy PoE Installation Instructions (prior to 2020)...........................52

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 4 of 63
CB 2 Series
Administrator Guide
32 CB 2 24V or Multi-Tap Power Brick Wiring (prior to 2020)..................53
33 CB 2 Series Standard Wiring (prior to 3/2013) (with Hammond Transformer)....54
34 Legacy Cb 2-e with Public Address Wiring Diagram..................55
35 Legacy CB 2-e with AED Housing Wiring Diagram.....................56
36 CB 2-s Wiring Diagram...................................................................57
37 Multi-Tap Transformer Wiring........................................................58
38 Maintenance Schedule...................................................................59
39 Locating Unit Serial Numbers.......................................................61
40 Warranty...........................................................................................62
41 Download Information....................................................................63

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 5 of 63
CB 2 Series
Administrator Guide
2 Introduction
The 2 Series Wall Mount Help Points®
This popular line is a good t for any indoor or outdoor application, including parking facilities. Our
unmistakable craftsmanship makes our Help Points®the most rugged on the market, withstanding
the punishment of natural and man-made disasters. All 2 Series units have a rugged steel construc-
tion, shatterproof Lexan Lens, industrial engineering grade re ective graphics and weather, UV and
graf ti resistant paint, and are illuminated by a high-powered, 270 lumens/92 candela LED blue
beacon/strobe. Other options include:
• IP and analog phones
• Long-life LED area light
• Low power consumption LED faceplate light
• Camera and card reader openings
• Temperature-controlled automated external de brillator (AED) housing
• Public address speakers
CB 2-e CB 2-e with Public Address CB 2-e with AED Housing
CB 2-e with AED Housing
CB 2-e with AED Housing
CB 2-sCB 2-a

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 6 of 63
CB 2 Series
Administrator Guide
3 Getting Started
Basic Install Instructions
1. EIA/TIA, ANSI, CSA and BICSI cabling or similar standards shall be adhered to for proper
operation of Code Blue communication devices connected to copper or ber infrastructures.
Communications cable and electrical cable in the same conduit is not an acceptable instal-
lation and shall not be supported. Analog phones require a minimum of 23mA for proper
operation (26-29mA recommended).
2. Each analog speakerphone requires its own phone line or PBX extension. Multiple units
shall not be supported.
3. Speakerphones require programming before operation. Consult the User Guide or
Administrator Guide enclosed with the unit or visit www.codeblue.com > Support >
Downloads to read or download manuals.
4. If you are installing IP speakerphones, please read the appropriate manuals and consult
with your Network Administrator.
5. Size electrical wiring based on length of run.
6. Consult the enclosed document packet for internal wiring instructions.
Tools Required
CB 2 Series
1. Drill and security bit for removing and inserting security screws on phone and access plate
2. Phillips head screwdriver and at head screwdriver
3. 3/8 socket set to mount unit onto wall

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 7 of 63
CB 2 Series
Administrator Guide
4 Spare Parts
CB 2-a & CB 2-e (2020)
Part Part Number
S-2000 LED Strobe Light 41162
Analog Phone Line Surge Suppressor 41471
IP Phone Line Surge Suppressor 41421
DIN Rail Assy 40110
PoE Switch 41574
Button Head Screws 41500
HID Lens 41164
Legacy CB 2-e
Part Part Number
LED Strobe Light 40159
Button Head Security Screws (3-pack) 41500
Analog Phone Line Surge Suppressor 41471
IP Phone Line Surge Suppressor 41421
Manifold R/B 5-way 40101
Power Brick 120V, 240V & 277V 40104
Legacy CB 2-e with Public Address
Part Part Number
LED Strobe Light 40159
Button Head Security Screws (3-pack) 41500
Analog Phone Line Surge Suppressor 41471
IP Phone Line Surge Suppressor 41421
Manifold R/B 5-way 40101
PAS AMP Kit 24V 40009
Power Brick 120V, 240V & 277V 40104
PAS Speaker 40080

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 8 of 63
CB 2 Series
Administrator Guide
Legacy CB 2-e with AED Housing
Part Part Number
LED Strobe Light 40159
Button Head Security Screws (3-pack) 41500
Analog Phone Line Surge Suppressor 41471
IP Phone Line Surge Suppressor 41421
Manifold R/B 5-way 40101
Power Brick 120V, 240V & 277V 40104
AED Housing Door Release Mechanism 41104
AED Housing Heater 41105
AED Housing Thermostat 41106
AED Housing Door Controller 41107
AED Housing Retrot kit 40012
CB 2-s
Part Part Number
LED Strobe Light 40159
Button Head Security Screws (3-pack) 41500
Analog Phone Line Surge Suppressor 41471
IP Phone Line Surge Suppressor 41421
Manifold R/B 5-way 40101
Power Brick 120V, 240V & 277V 40104
LED Area Light 41539
CB 2 Series Additional Options
Quantity Part Description
1 Document packet (Installation and Setup)
1 Hardware packet
4 Lag screw sleeves
4 Metal washers
4 Rubber washers
1 Security bit
1 Enclosure
2 10/24 Counter sunk security screws – CB 2-s only
2 Key fobs – CB 2-e with AED only

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 9 of 63
CB 2 Series
Administrator Guide
5 Power Requirements (2020)
(The following power requirements include the 2 Series and also ALL OTHER Code Blue units.)
Component Specs
Faceplates Voltage Max Current Max Watts Norm Current Norm Watts KWHrs
High Votage AC Components Voltage Current Watts KWHrs
IA4100 24V AC 0.40 9.60 0.22 5.28 0.13
Multi-Tap Power Supply 120V AC 1.75A/210VAC 210 5.04
12V DC 0.90 10.80 0.39 4.68 0.11
Din Rail Power Supply 120V AC 1.2A/115VAC 115 2.76
24V DC 0.90 21.60 0.39 9.36 0.22
Heater -AED 120V AC 1.6 192 4.61
IP5000 24V AC 0.10 2.40 0.07 1.68 0.04
DC - PS AED 120V AC 2.6 312 7.49
12V DC 0.19 2.28 0.15 1.8 0.04
PAS Amp 120V AC 3.83 459.6 11.03
24V DC 0.19 4.56 0.15 3.6 0.09
Centry®12V DC 0.50 6.00 0.38 4.56 0.11
Lights Voltage Max Current Max Watts Norm Current Norm Watts KWHrs
High Voltage Models Voltage Current Watts KWHrs
S-1000 LED Strobe 24V AC 2.80 67.20 0.22 5.28 0.13
CB 1 AED 120V AC 3.35 402 9.6
12V DC 0.26 3.12 0.24 2.88 0.07
CB 2 AED 120V AC 3.35 402 9.6
24V DC 0.26 6.24 0.24 5.76 0.14
CB 1 PAS 120V AC 3.83 460 11
A-700 Area Light 24 VAC 1.80 43.20 0.83 19.92 0.48
CB 5 PAS 120V AC 3.33 400 9.6
12V DC 2.68 32.16 0.38 4.56 0.11
CB 1-s w/ NightCharge®120V AC 2.5 300 2.4
24V DC 2.68 64.32 0.38 9.12 0.22
CB 4-u w/ NightCharge®120V AC 2.5 300 2.4
S-1050 LED Strobe w/ Photocell 24V AC 2.80 67.20 0.22 5.28 0.13
12V DC 2.68 32.16 0.38 4.56 0.11
24V DC 2.68 64.32 0.38 9.12 0.22
LED Light Bar 24V AC 0.04 0.96 0.04 0.96 0.02
12V DC 0.04 0.48 0.04 0.48 0.01
24V DC 0.04 0.96 0.04 0.96 0.02
WM-180 PAS with LED Strobe 24V AC 7.30 175.20 2.10 50.4 1.21
Common Configurations
Models With IA4100 Faceplate Voltage Current Watts KWHrs Models With IP5000 Faceplate Voltage Current Watts KWHrs
CB 1-e 24V AC 0.48 11.52 0.28 CB 1-e 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19 12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39 24V DC 0.43 10.32 0.25
CB 1-s 24V AC 1.31 31.44 0.75 CB 1-s 24V AC 1.16 27.84 0.67
12V DC 1.05 12.60 0.30 12V DC 0.81 9.72 0.23
24V DC 1.05 25.20 0.60 24V DC 0.81 19.44 0.47
CB 5-s/5-p 24V AC 0.48 11.52 0.28 CB 5-s/5-p 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19 12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39 24V DC 0.43 10.32 0.25
CB 9-s 24V AC 0.26 6.24 0.15 CB 9-s 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12 12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25 24V DC 0.19 4.56 0.11
CB 2-e 24V AC 0.44 10.56 0.25 CB 2-e 24V AC 0.29 6.96 0.17
12V DC 0.63 7.56 0.18 12V DC 0.39 4.68 0.11
24V DC 0.63 15.12 0.36 24V DC 0.39 9.36 0.22
CB 2-a 24V AC 0.48 11.52 0.28 CB 2-a 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19 12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39 24V DC 0.43 10.32 0.25
CB 2-s 24V AC 1.31 31.44 0.75 CB 2-s 24V AC 1.16 27.84 0.67
12V DC 1.05 12.60 0.30 12V DC 0.81 9.72 0.23
24V DC 1.05 25.20 0.60 24V DC 0.81 19.44 0.47
CB 2-e W/ PAS 24V AC 6.44 154.56 3.71 CB 2-e / PAS 24V AC 6.44 154.56 3.71
CB 4-s 24V AC 0.22 5.28 0.13 CB 4-s 24V AC 0.07 1.68 0.04
12V DC 0.39 4.68 0.11 12V DC 0.15 1.8 0.04
24V DC 0.39 9.36 0.22 24V DC 0.15 3.6 0.09
CB 4-r 24V AC 0.26 6.24 0.15 CB 4-r 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12 12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25 24V DC 0.19 4.56 0.11
CB 4-u 24V AC 0.26 6.24 0.15 CB 4-u 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12 12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25 24V DC 0.19 4.56 0.11
Surface Mount/Flush Mount 24V AC 0.22 5.28 0.13 Surface Mount/Flush Mount 24V AC 0.07 1.68 0.04
12V DC 0.39 4.68 0.11 12V DC 0.15 1.8 0.04
24V DC 0.39 9.36 0.22 24V DC 0.15 3.6 0.09
CB RT 24V AC 1.10 26.33 0.63 CB RT 24V AC 1.21 28.96 0.70
12V DC 0.81 9.75 0.23 12V DC 1.03 12.37 0.30
24V DC 1.61 38.57 0.93 24V DC 1.13 27.10 0.65
Component Specs
Faceplates Voltage Max Current Max Watts Norm Current Norm Watts KWHrs
High Votage AC Components Voltage Current Watts KWHrs
IA4100 24V AC 0.40 9.60 0.22 5.28 0.13
Multi-Tap Power Supply 120V AC 1.75A/210VAC 210 5.04
12V DC 0.90 10.80 0.39 4.68 0.11
Din Rail Power Supply 120V AC 1.2A/115VAC 115 2.76
24V DC 0.90 21.60 0.39 9.36 0.22
Heater -AED 120V AC 1.6 192 4.61
IP5000 24V AC 0.10 2.40 0.07 1.68 0.04
DC - PS AED 120V AC 2.6 312 7.49
12V DC 0.19 2.28 0.15 1.8 0.04
PAS Amp 120V AC 3.83 459.6 11.03
24V DC 0.19 4.56 0.15 3.6 0.09
Centry®12V DC 0.50 6.00 0.38 4.56 0.11
Lights Voltage Max Current Max Watts Norm Current Norm Watts KWHrs
High Voltage Models Voltage Current Watts KWHrs
S-1000 LED Strobe 24V AC 2.80 67.20 0.22 5.28 0.13
CB 1 AED 120V AC 3.35 402 9.6
12V DC 0.26 3.12 0.24 2.88 0.07
CB 2 AED 120V AC 3.35 402 9.6
24V DC 0.26 6.24 0.24 5.76 0.14
CB 1 PAS 120V AC 3.83 460 11
A-700 Area Light 24 VAC 1.80 43.20 0.83 19.92 0.48
CB 5 PAS 120V AC 3.33 400 9.6
12V DC 2.68 32.16 0.38 4.56 0.11
CB 1-s w/ NightCharge®120V AC 2.5 300 2.4
24V DC 2.68 64.32 0.38 9.12 0.22
CB 4-u w/ NightCharge®120V AC 2.5 300 2.4
S-1050 LED Strobe w/ Photocell 24V AC 2.80 67.20 0.22 5.28 0.13
12V DC 2.68 32.16 0.38 4.56 0.11
24V DC 2.68 64.32 0.38 9.12 0.22
LED Light Bar 24V AC 0.04 0.96 0.04 0.96 0.02
12V DC 0.04 0.48 0.04 0.48 0.01
24V DC 0.04 0.96 0.04 0.96 0.02
WM-180 PAS with LED Strobe 24V AC 7.30 175.20 2.10 50.4 1.21
Common Configurations
Models With IA4100 Faceplate Voltage Current Watts KWHrs Models With IP5000 Faceplate Voltage Current Watts KWHrs
CB 1-e 24V AC 0.48 11.52 0.28 CB 1-e 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19 12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39 24V DC 0.43 10.32 0.25
CB 1-s 24V AC 1.31 31.44 0.75 CB 1-s 24V AC 1.16 27.84 0.67
12V DC 1.05 12.60 0.30 12V DC 0.81 9.72 0.23
24V DC 1.05 25.20 0.60 24V DC 0.81 19.44 0.47
CB 5-s/5-p 24V AC 0.48 11.52 0.28 CB 5-s/5-p 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19 12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39 24V DC 0.43 10.32 0.25
CB 9-s 24V AC 0.26 6.24 0.15 CB 9-s 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12 12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25 24V DC 0.19 4.56 0.11
CB 2-e 24V AC 0.44 10.56 0.25 CB 2-e 24V AC 0.29 6.96 0.17
12V DC 0.63 7.56 0.18 12V DC 0.39 4.68 0.11
24V DC 0.63 15.12 0.36 24V DC 0.39 9.36 0.22
CB 2-a 24V AC 0.48 11.52 0.28 CB 2-a 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19 12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39 24V DC 0.43 10.32 0.25
CB 2-s 24V AC 1.31 31.44 0.75 CB 2-s 24V AC 1.16 27.84 0.67
12V DC 1.05 12.60 0.30 12V DC 0.81 9.72 0.23
24V DC 1.05 25.20 0.60 24V DC 0.81 19.44 0.47
CB 2-e W/ PAS 24V AC 6.44 154.56 3.71 CB 2-e / PAS 24V AC 6.44 154.56 3.71
CB 4-s 24V AC 0.22 5.28 0.13 CB 4-s 24V AC 0.07 1.68 0.04
12V DC 0.39 4.68 0.11 12V DC 0.15 1.8 0.04
24V DC 0.39 9.36 0.22 24V DC 0.15 3.6 0.09
CB 4-r 24V AC 0.26 6.24 0.15 CB 4-r 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12 12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25 24V DC 0.19 4.56 0.11
CB 4-u 24V AC 0.26 6.24 0.15 CB 4-u 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12 12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25 24V DC 0.19 4.56 0.11
Surface Mount/Flush Mount 24V AC 0.22 5.28 0.13 Surface Mount/Flush Mount 24V AC 0.07 1.68 0.04
12V DC 0.39 4.68 0.11 12V DC 0.15 1.8 0.04
24V DC 0.39 9.36 0.22 24V DC 0.15 3.6 0.09
CB RT 24V AC 1.10 26.33 0.63 CB RT 24V AC 1.21 28.96 0.70
12V DC 0.81 9.75 0.23 12V DC 1.03 12.37 0.30
24V DC 1.61 38.57 0.93 24V DC 1.13 27.10 0.65

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 10 of 63
CB 2 Series
Administrator Guide
Power Requirements continued
Component Specs
Faceplates Voltage Max Current Max Watts Norm Current Norm Watts KWHrs High Votage AC Components Voltage Current Watts KWHrs
IA4100 24V AC 0.40 9.60 0.22 5.28 0.13 Multi-Tap Power Supply 120V AC 1.75A/210VAC 210 5.04
12V DC 0.90 10.80 0.39 4.68 0.11 Din Rail Power Supply 120V AC 1.2A/115VAC 115 2.76
24V DC 0.90 21.60 0.39 9.36 0.22 Heater -AED 120V AC 1.6 192 4.61
IP5000 24V AC 0.10 2.40 0.07 1.68 0.04 DC - PS AED 120V AC 2.6 312 7.49
12V DC 0.19 2.28 0.15 1.8 0.04 PAS Amp 120V AC 3.83 459.6 11.03
24V DC 0.19 4.56 0.15 3.6 0.09
Centry®12V DC 0.50 6.00 0.38 4.56 0.11
Lights Voltage Max Current Max Watts Norm Current Norm Watts KWHrs High Voltage Models Voltage Current Watts KWHrs
S-1000 LED Strobe 24V AC 2.80 67.20 0.22 5.28 0.13 CB 1 AED 120V AC 3.35 402 9.6
12V DC 0.26 3.12 0.24 2.88 0.07 CB 2 AED 120V AC 3.35 402 9.6
24V DC 0.26 6.24 0.24 5.76 0.14 CB 1 PAS 120V AC 3.83 460 11
A-700 Area Light 24 VAC 1.80 43.20 0.83 19.92 0.48 CB 5 PAS 120V AC 3.33 400 9.6
12V DC 2.68 32.16 0.38 4.56 0.11
CB 1-s w/ NightCharge®120V AC 2.5 300 2.4
24V DC 2.68 64.32 0.38 9.12 0.22
CB 4-u w/ NightCharge®120V AC 2.5 300 2.4
S-1050 LED Strobe w/ Photocell 24V AC 2.80 67.20 0.22 5.28 0.13
12V DC 2.68 32.16 0.38 4.56 0.11
24V DC 2.68 64.32 0.38 9.12 0.22
LED Light Bar 24V AC 0.04 0.96 0.04 0.96 0.02
12V DC 0.04 0.48 0.04 0.48 0.01
24V DC 0.04 0.96 0.04 0.96 0.02
WM-180 PAS with LED Strobe 24V AC 7.30 175.20 2.10 50.4 1.21
Common Configurations
Models With IA4100 Faceplate Voltage Current Watts KWHrs
Models With IP5000 Faceplate Voltage Current Watts KWHrs
CB 1-e 24V AC 0.48 11.52 0.28
CB 1-e 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19
12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39
24V DC 0.43 10.32 0.25
CB 1-s 24V AC 1.31 31.44 0.75
CB 1-s 24V AC 1.16 27.84 0.67
12V DC 1.05 12.60 0.30
12V DC 0.81 9.72 0.23
24V DC 1.05 25.20 0.60
24V DC 0.81 19.44 0.47
CB 5-s/5-p 24V AC 0.48 11.52 0.28
CB 5-s/5-p 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19
12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39
24V DC 0.43 10.32 0.25
CB 9-s 24V AC 0.26 6.24 0.15
CB 9-s 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12
12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25
24V DC 0.19 4.56 0.11
CB 2-e 24V AC 0.44 10.56 0.25
CB 2-e 24V AC 0.29 6.96 0.17
12V DC 0.63 7.56 0.18
12V DC 0.39 4.68 0.11
24V DC 0.63 15.12 0.36
24V DC 0.39 9.36 0.22
CB 2-a 24V AC 0.48 11.52 0.28
CB 2-a 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19
12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39
24V DC 0.43 10.32 0.25
CB 2-s 24V AC 1.31 31.44 0.75
CB 2-s 24V AC 1.16 27.84 0.67
12V DC 1.05 12.60 0.30
12V DC 0.81 9.72 0.23
24V DC 1.05 25.20 0.60
24V DC 0.81 19.44 0.47
CB 2-e W/ PAS 24V AC 6.44 154.56 3.71
CB 2-e / PAS 24V AC 6.44 154.56 3.71
CB 4-s 24V AC 0.22 5.28 0.13
CB 4-s 24V AC 0.07 1.68 0.04
12V DC 0.39 4.68 0.11
12V DC 0.15 1.8 0.04
24V DC 0.39 9.36 0.22
24V DC 0.15 3.6 0.09
CB 4-r 24V AC 0.26 6.24 0.15
CB 4-r 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12
12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25
24V DC 0.19 4.56 0.11
CB 4-u 24V AC 0.26 6.24 0.15
CB 4-u 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12
12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25
24V DC 0.19 4.56 0.11
Surface Mount/Flush Mount 24V AC 0.22 5.28 0.13
Surface Mount/Flush Mount 24V AC 0.07 1.68 0.04
12V DC 0.39 4.68 0.11
12V DC 0.15 1.8 0.04
24V DC 0.39 9.36 0.22
24V DC 0.15 3.6 0.09
CB RT 24V AC 1.10 26.33 0.63
CB RT 24V AC 1.21 28.96 0.70
12V DC 0.81 9.75 0.23
12V DC 1.03 12.37 0.30
24V DC 1.61 38.57 0.93
24V DC 1.13 27.10 0.65

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 11 of 63
CB 2 Series
Administrator Guide
Power Requirements continued
Component Specs
Faceplates Voltage Max Current Max Watts Norm Current Norm Watts KWHrs High Votage AC Components Voltage Current Watts KWHrs
IA4100 24V AC 0.40 9.60 0.22 5.28 0.13 Multi-Tap Power Supply 120V AC 1.75A/210VAC 210 5.04
12V DC 0.90 10.80 0.39 4.68 0.11 Din Rail Power Supply 120V AC 1.2A/115VAC 115 2.76
24V DC 0.90 21.60 0.39 9.36 0.22 Heater -AED 120V AC 1.6 192 4.61
IP5000 24V AC 0.10 2.40 0.07 1.68 0.04 DC - PS AED 120V AC 2.6 312 7.49
12V DC 0.19 2.28 0.15 1.8 0.04 PAS Amp 120V AC 3.83 459.6 11.03
24V DC 0.19 4.56 0.15 3.6 0.09
Centry®12V DC 0.50 6.00 0.38 4.56 0.11
Lights Voltage Max Current Max Watts Norm Current Norm Watts KWHrs High Voltage Models Voltage Current Watts KWHrs
S-1000 LED Strobe 24V AC 2.80 67.20 0.22 5.28 0.13 CB 1 AED 120V AC 3.35 402 9.6
12V DC 0.26 3.12 0.24 2.88 0.07 CB 2 AED 120V AC 3.35 402 9.6
24V DC 0.26 6.24 0.24 5.76 0.14 CB 1 PAS 120V AC 3.83 460 11
A-700 Area Light 24 VAC 1.80 43.20 0.83 19.92 0.48 CB 5 PAS 120V AC 3.33 400 9.6
12V DC 2.68 32.16 0.38 4.56 0.11
CB 1-s w/ NightCharge®120V AC 2.5 300 2.4
24V DC 2.68 64.32 0.38 9.12 0.22
CB 4-u w/ NightCharge®120V AC 2.5 300 2.4
S-1050 LED Strobe w/ Photocell 24V AC 2.80 67.20 0.22 5.28 0.13
12V DC 2.68 32.16 0.38 4.56 0.11
24V DC 2.68 64.32 0.38 9.12 0.22
LED Light Bar 24V AC 0.04 0.96 0.04 0.96 0.02
12V DC 0.04 0.48 0.04 0.48 0.01
24V DC 0.04 0.96 0.04 0.96 0.02
WM-180 PAS with LED Strobe 24V AC 7.30 175.20 2.10 50.4 1.21
Common Configurations
Models With IA4100 Faceplate Voltage Current Watts KWHrs
Models With IP5000 Faceplate Voltage Current Watts KWHrs
CB 1-e 24V AC 0.48 11.52 0.28
CB 1-e 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19
12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39
24V DC 0.43 10.32 0.25
CB 1-s 24V AC 1.31 31.44 0.75
CB 1-s 24V AC 1.16 27.84 0.67
12V DC 1.05 12.60 0.30
12V DC 0.81 9.72 0.23
24V DC 1.05 25.20 0.60
24V DC 0.81 19.44 0.47
CB 5-s/5-p 24V AC 0.48 11.52 0.28
CB 5-s/5-p 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19
12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39
24V DC 0.43 10.32 0.25
CB 9-s 24V AC 0.26 6.24 0.15
CB 9-s 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12
12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25
24V DC 0.19 4.56 0.11
CB 2-e 24V AC 0.44 10.56 0.25
CB 2-e 24V AC 0.29 6.96 0.17
12V DC 0.63 7.56 0.18
12V DC 0.39 4.68 0.11
24V DC 0.63 15.12 0.36
24V DC 0.39 9.36 0.22
CB 2-a 24V AC 0.48 11.52 0.28
CB 2-a 24V AC 0.33 7.92 0.19
12V DC 0.67 8.04 0.19
12V DC 0.43 5.16 0.12
24V DC 0.67 16.08 0.39
24V DC 0.43 10.32 0.25
CB 2-s 24V AC 1.31 31.44 0.75
CB 2-s 24V AC 1.16 27.84 0.67
12V DC 1.05 12.60 0.30
12V DC 0.81 9.72 0.23
24V DC 1.05 25.20 0.60
24V DC 0.81 19.44 0.47
CB 2-e W/ PAS 24V AC 6.44 154.56 3.71
CB 2-e / PAS 24V AC 6.44 154.56 3.71
CB 4-s 24V AC 0.22 5.28 0.13
CB 4-s 24V AC 0.07 1.68 0.04
12V DC 0.39 4.68 0.11
12V DC 0.15 1.8 0.04
24V DC 0.39 9.36 0.22
24V DC 0.15 3.6 0.09
CB 4-r 24V AC 0.26 6.24 0.15
CB 4-r 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12
12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25
24V DC 0.19 4.56 0.11
CB 4-u 24V AC 0.26 6.24 0.15
CB 4-u 24V AC 0.11 2.64 0.06
12V DC 0.43 5.16 0.12
12V DC 0.19 2.28 0.05
24V DC 0.43 10.32 0.25
24V DC 0.19 4.56 0.11
Surface Mount/Flush Mount 24V AC 0.22 5.28 0.13
Surface Mount/Flush Mount 24V AC 0.07 1.68 0.04
12V DC 0.39 4.68 0.11
12V DC 0.15 1.8 0.04
24V DC 0.39 9.36 0.22
24V DC 0.15 3.6 0.09
CB RT 24V AC 1.10 26.33 0.63
CB RT 24V AC 1.21 28.96 0.70
12V DC 0.81 9.75 0.23
12V DC 1.03 12.37 0.30
24V DC 1.61 38.57 0.93
24V DC 1.13 27.10 0.65

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 12 of 63
CB 2 Series
Administrator Guide
6 Legacy Power Requirements
(The following power requirements include the 2 Series and also ALL OTHER Code Blue units.)

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 13 of 63
CB 2 Series
Administrator Guide

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 14 of 63
CB 2 Series
Administrator Guide
7 Software Configuration
Blue Alert® MNS Software
Blue Alert MNS (Mass Notication Software) lls a need in the marketplace for an incident response
solution that is both comprehensive and cost-effective, while also providing an efcient way to detect
and respond. The advanced mass notication system allows responders to deliver multi-layered
emergency notications via a wide range of platforms, including email, text message (SMS), emer-
gency phones, public address speakers, social media, desktop alerts and more, quickly informing
and directing people in emergency situations.
Blue Alert® EMS
Blue Alert EMS is an advanced software solution that handles all incoming events effectively by re-
motely controlling emergency communication devices with an easy-to-use Graphical User Interface
(GUI). You also will have the ability to open gates and AED access doors, turn LED beacon/strobes
on or off, transfer calls to Public Address Systems to make area wide announcements and incor-
porate other ancillary devices and applications while the system securely archives data for future
reference.
ToolVox®
A sophisticated emergency management platform for your blue light phone network, ToolVox offers
unique real-time monitoring and provisioning options for emergency phones and public address
speakers, effectively acting as a hub for connecting Help Points®and other Code Blue devices. Us-
ing our proprietary incident response software, Blue Alert®MNS and EMS, you can send alerts via
outdoor platforms, such as blue light phones and public address speakers. It also provides connec-
tions to PBX, public telephone (PSTN) and Internet (ISP) networks, in addition to third party security
platforms.

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 15 of 63
CB 2 Series
Administrator Guide
8 CB 2-a Exploded View
DISCLAIMER: Product design and component use subject to change without notice. Product shown reasonably represents current offering and
is intended to assist in component identication. Reference the model and serial number from the unit ID tag and contact manufacturer to conrm
replacement part version and availability.
4
6
2
7
8
1
5
3
12
10
11
9
ITEM # DESCRIPTION QTY
1 Wall Mount Shell Assy 1
2 2 Series Wall Plate Assy 1
3 LED Faceplate Light 1
4 LED Blue Beacon Strobe 1
5 Standard / Custom Graphic 2
6DIN Rail Assy 1
7 28” Harness, 4 Connector 1
8 28” Harness, 1 Connector 1
9 Lens 1
10 10-24 Nylock Nut 7
11 Lens Retainer Bracket Long 1
12 Lens Retainer Bracket Short 2

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 16 of 63
CB 2 Series
Administrator Guide
9 CB 2-e Exploded View
DISCLAIMER: Product design and component use subject to change without notice. Product shown reasonably represents current offering and
is intended to assist in component identication. Reference the model and serial number from the unit ID tag and contact manufacturer to conrm
replacement part version and availability.
5
3
2
6
7
1
4
11
9
10
8
ITEM # DESCRIPTION QTY
1 Wall Mount Shell Assy 1
2 2 Series Wall Plate Assy 1
3 LED Blue Beacon Strobe 1
4 Standard / Custom Graphic 2
5DIN Rail Assy 1
6 28” Harness, 4 Connector 1
7 28” Harness, 1 Connector 1
8 Lens 1
9 10-24 Nylock Nut 7
10 Lens Retainer Bracket Long 1
11 Lens Retainer Bracket Short 1

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 17 of 63
CB 2 Series
Administrator Guide
10 Legacy CB 2-e Low Voltage Exploded View
DISCLAIMER: Product design and component use subject to change without notice. Product shown reasonably represents current offering and
is intended to assist in component identication. Reference the model and serial number from the unit ID tag and contact manufacturer to conrm
replacement part version and availability.
3
2
4
4
4
1
4
5
9
8
7
6
4
10
3
2
4
4
4
1
4
5
9
8
7
6
4
10
BALL # PART # DESCRIPTION
1 41425 HID Lens
2 40159 LED Beacon Strobe
3 41500 Button head Security Screw (3 pk)
4 40102 Wall Anchor Kit
5 41471 Analog Surge Suppressor
5 41421 IP Surge Suppressor
6 CALL Standard / Custom Graphic
7 50001 Single Button IA4100 Analog Phone – PUSH FOR HELP
7 50002 Double Button IA4100 Analog Phone – PUSH FOR HELP
7 50003 Keypad IA4100 Analog Phone – PUSH FOR HELP
7 50004 Single Button IA4100 Analog Phone – EMERGENCY
7 50005 Double Button IA4100 Analog Phone – EMERGENCY
7 50006 Keypad IA4100 Analog Phone – EMERGENCY
7 50101 Single Button IP5000 VoIP Phone – PUSH FOR HELP
BALL # PART # DESCRIPTION
7 50102 Double Button IP5000 VoIP Phone – PUSH FOR HELP
7 50103 Keypad IP5000 VoIP Phone – PUSH FOR HELP
7 50104 Single Button IP5000 VoIP Phone – EMERGENCY
7 50105 Double Button IP5000 VoIP Phone – EMERGENCY
7 50106 Keypad IP5000 VoIP Phone – EMERGENCY
8 41544 Faceplate Security Screw 10x24 (6 pk)
9 40101 Manifold R/B 5-way
10 40357 Bezel Assembly IA4100 Analog Phone – PUSH FOR HELP
10 40407 Bezel Assembly IA4100 Analog Phone – EMERGENCY
10 40313 Bezel Assembly IP5000 VoIP Phone – PUSH FOR HELP
10 40405 Bezel Assembly IP5000 VoIP Phone – EMERGENCY

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 18 of 63
CB 2 Series
Administrator Guide
11 Legacy CB 2-e High Voltage Exploded View
DISCLAIMER: Product design and component use subject to change without notice. Product shown reasonably represents current offering and
is intended to assist in component identication. Reference the model and serial number from the unit ID tag and contact manufacturer to conrm
replacement part version and availability.
3
2
3
4
4
1
4
9
8
7
6
10
5
3
2
3
4
4
1
4
9
8
7
6
10
5
BALL # PART # DESCRIPTION
1 41425 HID Lens
2 40159 LED Beacon Strobe
3 41500 Button Head Security Screws (3 pk)
4 40102 Wall Anchor Kit
5 41471 Analog Surge Suppressor
5 41421 IP Surge Suppressor
6 CALL Standard Graphic
6 CALL Custom Graphic
7 50001 Single Button IA4100 Analog Phone – PUSH FOR HELP
7 50002 Double Button IA4100 Analog Phone – PUSH FOR HELP
7 50003 Keypad IA4100 Analog Phone – PUSH FOR HELP
7 50004 Single Button IA4100 Analog Phone – EMERGENCY
7 50005 Double Button IA4100 Analog Phone – EMERGENCY
7 50006 Keypad IA4100 Analog Phone – EMERGENCY
BALL # PART # DESCRIPTION
7 50101 Single Button IP5000 VoIP Phone – PUSH FOR HELP
7 50102 Double Button IP5000 VoIP Phone – PUSH FOR HELP
7 50103 Keypad IP5000 VoIP Phone – PUSH FOR HELP
7 50104 Single Button IP5000 VoIP Phone – EMERGENCY
7 50105 Double Button IP5000 VoIP Phone – EMERGENCY
7 50106 Keypad IP5000 VoIP Phone – EMERGENCY
8 41544 Faceplate Security Screw 10x24 (6 pk)
9 40104 Power Brick 120V, 240V, 277V, 347V
10 40357 Bezel Assembly IA4100 Analog Phone – PUSH FOR HELP
10 40407 Bezel Assembly IA4100 Analog Phone – EMERGENCY
10 40313 Bezel Assembly IP5000 VoIP Phone – PUSH FOR HELP
10 40405 Bezel Assembly IP5000 VoIP Phone – EMERGENCY

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 19 of 63
CB 2 Series
Administrator Guide
12 CB 2-s Low Voltage Exploded View
DISCLAIMER: Product design and component use subject to change without notice. Product shown reasonably represents current offering and
is intended to assist in component identication. Reference the model and serial number from the unit ID tag and contact manufacturer to conrm
replacement part version and availability.
9
3
7
10
4
14
5
6
8
2
1
13
12
11
BALL # PART # DESCRIPTION
1 40357 Bezel Assembly IA4100 Analog Phone – PUSH FOR HELP
1 40407 Bezel Assembly IA4100 Analog Phone – EMERGENCY
1 40313 Bezel Assembly IP5000 VoIP Phone – PUSH FOR HELP
1 40405 Bezel Assembly IP5000 VoIP Phone – EMERGENCY
2 50001 Single Button IA4100 Analog Phone – PUSH FOR HELP
2 50002 Double Button IA4100 Analog Phone – PUSH FOR HELP
2 50003 Keypad IA4100 Analog Phone – PUSH FOR HELP
2 50004 Single Button IA4100 Analog Phone – EMERGENCY
2 50005 Double Button IA4100 Analog Phone – EMERGENCY
2 50006 Keypad IA4100 Analog Phone – EMERGENCY
2 50101 Single Button IP5000 VoIP Phone – PUSH FOR HELP
2 50102 Double Button IP5000 VoIP Phone – PUSH FOR HELP
2 50103 Keypad IP5000 VoIP Phone – PUSH FOR HELP
2 50104 Single Button IP5000 VoIP Phone – EMERGENCY
BALL # PART # DESCRIPTION
2 50105 Double Button IP5000 VoIP Phone – EMERGENCY
2 50106 Keypad IP5000 VoIP Phone – EMERGENCY
3 41544 Faceplate Security Screw 10x24 (6 pk)
4 41548 LED Faceplate Light
5 CALL Standard / Custom Graphic
6 41471 Analog Surge Suppressor
6 41421 IP Surge Suppressor
7 41539 LED Area Light
8 41544 Faceplate Security Screw 10x24 (6 pk)
9 41412 HID Lens
10 40159 LED Blue Beacon Strobe
11 40543 Strobe Disk (3 pk)
12 10084 Clear Strobe Spacer
13 40102 Wall Mount Hardware Kit
14 40101 Manifold R/B 5-way

Code Blue •259 Hedcor Street •Holland, MI 49423 USA •800.205.7186 •www.codeblue.com GU-149-AApage 20 of 63
CB 2 Series
Administrator Guide
13 CB 2-s High Voltage Exploded View
DISCLAIMER: Product design and component use subject to change without notice. Product shown reasonably represents current offering and
is intended to assist in component identication. Reference the model and serial number from the unit ID tag and contact manufacturer to conrm
replacement part version and availability.
9
3
7
10
4
14
5
6
8
2
1
13
12
11
BALL # PART # DESCRIPTION
1 40357 Bezel Assembly IA4100 Analog Phone – PUSH FOR HELP
1 40407 Bezel Assembly IA4100 Analog Phone – EMERGENCY
1 40313 Bezel Assembly IP5000 VoIP Phone – PUSH FOR HELP
1 40405 Bezel Assembly IP5000 VoIP Phone – EMERGENCY
2 50001 Single Button IA4100 Analog Phone – PUSH FOR HELP
2 50002 Double Button IA4100 Analog Phone – PUSH FOR HELP
2 50003 Keypad IA4100 Analog Phone – PUSH FOR HELP
2 50004 Single Button IA4100 Analog Phone – EMERGENCY
2 50005 Double Button IA4100 Analog Phone – EMERGENCY
2 50006 Keypad IA4100 Analog Phone – EMERGENCY
2 50101 Single Button IP5000 VoIP Phone – PUSH FOR HELP
2 50102 Double Button IP5000 VoIP Phone – PUSH FOR HELP
2 50103 Keypad IP5000 VoIP Phone – PUSH FOR HELP
2 50104 Single Button IP5000 VoIP Phone – EMERGENCY
BALL # PART # DESCRIPTION
2 50105 Double Button IP5000 VoIP Phone – EMERGENCY
2 50106 Keypad IP5000 VoIP Phone – EMERGENCY
3 41544 Faceplate Security Screw 10x24 (6 pk)
4 41548 LED Faceplate Light
5 CALL Standard / Custom Graphic
6 41471 Analog Surge Suppressor
6 41421 IP Surge Suppressor
7 41539 LED Area Light
8 41544 Faceplate Security Screw 10x24 (6 pk)
9 41412 HID Lens
10 40159 LED Blue Beacon Strobe
11 40543 Strobe Disk (3 pk)
12 10084 Clear Strobe Spacer
13 40102 Wall Mount Hardware Kit
14 40105 Power Brick 120V, 240V, 277V, 347V
Other manuals for CB 2 Series
2
This manual suits for next models
3
Table of contents
Other Code Blue Intercom System manuals