Aiphone IS SERIES Manual

Thank you for selecting Aiphone for your communication and security needs. Please read this manual and the separate
“OPERATION MANUAL” carefully before setting and using this system.
Refer to the provided “INSTALLATION MANUAL” for complete information regarding this system.
*
IMPORTANT
Please read and understand the system setting procedures before beginning the setup process.
IS SERIES
Commercial & Security Video Intercom system
Local System
SETTING MANUAL
834168 A 0211YZ

2
CONTENTS
ABOUT THIS MANUAL............... 3
PURPOSE OF THE SYSTEM
SETTINGS ................................... 3
SETTING LIST............................. 4
STARTING UP THE SYSTEM ..... 8
System requirements for PC ....... 8
Starting up the system ................. 8
Setting the system conguration
[System conguration]
................. 9
MAKING THE SYSTEM
SETTINGS ................................. 10
The basic setting procedure...... 10
Making network settings
[Network setting] .........................11
Setting the administrator ID and
password [Administrator
setting]..........................................11
Registering areas [System
setting – Area registration]
(Required)
............................................. 12
Registering zones
[System
setting – Zone registration] ......... 12
Registering control units
[System setting – Control
units composition]...................... 12
Registering stations and PA
outputs [System setting –
Registering stations] .................. 13
Making detailed settings to
stations and control units
[System setting – Advanced
station settings]
............................. 14
Basic setting procedure..........................14
Making detailed settings to door
stations or room sub stations ................14
Making detailed settings to master
stations ..................................................15
Making detailed settings to the central
control unit, add-on control unit(s) or
room sub control unit(s) ........................16
Registering stations and PA outputs
to zones [
System setting –
Zone setting] ............................... 17
Registering sound les for chime
[Chime setting – Registering
sound source]
.............................. 17
Registering sound sequences
[Chime setting – Registering
sound sequences]
.......................... 18
Registering daily chime schedule
[Chime setting – Registering
daily chime schedule]
....................... 18
Setting chime schedule
[Chime setting – Chime
schedule setting]..........................
19
Registering daily transfer schedule
[Transfer setting – Registering
daily transfer schedule]
................. 20
Setting transfer schedule
[Transfer setting – Transfer
schedule setting] ........................ 20
Setting the timer
[Timer setting]............................. 21
Setting time and date
[Time and date setting] .............. 22
Downloading/uploading setting
data [Setting le]......................... 22
nWhen downloading setting data
onto the PC ........................................22
nWhen uploading setting data..............22
Updating the system
[Updating the system] ................ 22
MAINTENANCE......................... 23
Initializing the system
[Initialization]............................... 23
Downloading system log
[System log] ................................ 23
Updating the rmware
[Firmware update]....................... 23
n
Downloading updated rmware data ...23
Referring to the troubleshooting
guide [Troubleshooting]............. 23

3
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
ABOUT THIS MANUAL
The IS system provides various manuals to meet various system planning and work processes. Use the manuals necessary for your
system.
Manual congurations
The following manuals are provided for a local system. Read all the manuals for installing, setting up, and using a local system, or
provide the manuals to the persons working with the system.
* The INSTALLATION MANUAL includes the contents for a standard (IP) system.
INSTALLATION MANUAL (A booklet included with the central control unit)
Used for installing and connecting control units and stations. (For an installer or serviceman)
SETTING MANUAL (This manual on the CD-ROM included with the central control unit)
This manual describes how to make the system settings and system maintenance. (For an installer or serviceman)
OPERATION MANUAL (An electronic manual on the CD-ROM included with the central control unit)
Information for using the system for calling, communicating, paging, monitoring, etc. (For users of the system)
PURPOSE OF THE SYSTEM SETTINGS
After the installation and connections of all the components are completed, congure the system settings based on how your system
is planned to be used. System settings must be completed before the system will operate.
CAUTION:
Make the settings correctly. If the settings are not made correctly, the system will not function as planned.
NOTE:
This manual is for setting a local system. To make settings for a standard (IP) system using an IP network, read
the SETTING MANUAL for the standard (IP) system.

4
SETTING LIST
The following is the list of system settings you can make via the web browser. The titles or items in shaded cells are required.
NOTE:
The following list is a brief overview of the setting items available in the system settings on a PC. The descriptions, and the style and order of
descriptions do not necessarily equate with the actual displays.
Title Sub title Item Sub item Setting range Default
(On the login
window)
- (Language) - English English
System
conguration
- - - Local system/Standard system
(IP system)
Local system
Network setting - IP version - IPv4 IPv4
(Select the network
setting method.)
- DHCP/Static IP Address DHCP
Static IP Address Static IP Address (required when
[Static IP Address] is selected)
- 192.168.0.30
Subnet Mask (required when
[Static IP Address] is selected)
- 255.255.255.0
Default Gateway 0 – 255 (for each eld) -
Primary DNS Server 0 – 255 (for each eld) -
Secondary DNS Server 0 – 255 (for each eld) -
MAC address - (Unmodiable) (Unmodiable)
Unit name - Up to 24 alphanumeric characters -
Web port - (Unmodiable) (Unmodiable)
Administrator
setting
- New administrator ID - Up to 16 alphanumeric characters -
Current Password - Up to 16 alphanumeric characters - (aiphone)
New Password - Up to 16 alphanumeric characters -
New Password
(Re-type)
- Up to 16 alphanumeric characters -
System setting Area registration Area name - Up to 24 alphanumeric characters (for
up to 99 areas)
1 (for Area
number 01)
Zone registration Zone name - Up to 24 alphanumeric characters (for
up to 99 zones)
-
Control units
composition
Room sub control
unit 1 to 4,
Add-on control unit 1
to 2
- Connected/Not connected Not connected
Registering
stations
Area (stations only) - (Area) 01 to 99 (Area) 01
Station number
(stations only)
- 001 to 999
0001 to 9999
00001 to 99999
-
Station name
(for stations)
- Up to 24 alphanumeric characters -
Station name
(for PA output)
(Required when
an external unit is
connected to the
corresponding PA
output terminals)
- Up to 24 alphanumeric characters -
Station type
(sub stations only)
- (Select from the registered ones.) (Depends on
the control
unit.)

5
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Title Sub title Item Sub item Setting range Default
System setting Advanced station
settings
Video door
station/Audio
door station/
Room sub
station
Called
stations
Call priority Normal/Priority/Urgent Normal
Called stations (Set up to 20 master stations from the
registered ones.)
-
Contact input
(room sub
stations only)
Contact type Normally open (NO)
/Normally closed (NC)
Normally open
(NO)
Call priority/Answering
the page
Answering the page
/Call (Normal/Priority/Urgent)
Normal
Other
Transmit volume boost
at PTT
ON/OFF
(ON: approx. +6dB up)
OFF
Camera zoom image
preset (video door
stations only)
0 (wide)/1/2/3/4/5/6/7/8/9 (zoom) 5 (Center)
Call acknowledge tone
on/off
ON/OFF ON
Backlight adjustment
(video door stations
only)
Exposure +/Exposure - Exposure +
Speaker
(room sub stations only)
Built-in speaker
/External speaker
Built-in
speaker
Master station Stations to be scan monitored (Select up to 20 sub stations from the
registered ones.)
-
Other
Master station function:
paging, chime, monitor,
door release, and
remote site call
ON/OFF ON
Central
control unit
Contact input
(Contact input) S1 to S4 S1
Contact type
Normally open (NO)
/Normally closed (NC)
Normally open
(NO)
Trigger condition None/Broadcast chime/Stop chime None
Sound source
(Only when "Broadcast
chime" is selected at
"Trigger condition")
Internal sound source (Select a
sound le or sequence name from the
registered ones in the list.)
/External sound source (Select either
External sound source 1 or 2.)
Internal sound
source: -
External sound
source: -
Chime priority
(Only when "Broadcast
chime" is selected for
"Trigger condition")
Normal/Priority/Urgent Normal
Zone name
(Only when "Broadcast
chime" is selected at
"Trigger condition")
(Select from the registered ones.) -
Contact output
(Contact output terminal) L1 to L8 L1
Contact type
Normally open (NO)
/Normally closed (NC)
Normally open
(NO)
Trigger condition None/Calling notice/Door release
/External sound source/PA output
None
Calling notice
(Only when "Calling
notice" is selected at
"Trigger condition")
Normal: OFF/ON
Priority: OFF/ON
Urgent: OFF/ON
Normal: OFF
Priority: OFF
Urgent: OFF
Door release
(Only when "Door
release" is selected at
"Trigger condition")
(Select from the sub stations registered
and set for the central control unit.)
-
External sound source
(Only when "External
sound source" is
selected at "Trigger
condition")
External sound source 1
/External sound source 2
-
PA output
(Only when "PA output"
is selected at "Trigger
condition")
PA output 1 to 4 -

6
Title Sub title Item Sub item Setting range Default
System setting Advanced station
settings
Room sub
control unit/
Add-on
control unit
Contact output
(Contact output
terminal)
L1 to L4 L1
Contact type
Normally open (NO)/Normally closed (NC) Normally open
(NO)
Trigger condition None/Calling notice/Door release/PA
output
None
Calling notice
(Only when "Calling
notice" is selected at
"Trigger condition")
Normal: OFF/ON
Priority: OFF/ON
Urgent: OFF/ON
Normal: OFF
Priority: OFF
Urgent: OFF
Door release
(Only when "Door
release" is selected at
"Trigger condition")
(Select from the sub stations registered
and set for each control unit.)
-
PA output
(Only when "PA output"
is selected at "Trigger
condition")
PA output 1 to 4 -
Zone setting Zone number - (Select from the registered ones.) -
Stations - (Select from the list.) -
PA outputs - (Select from the list.) -
Chime setting Registering sound
source
(Sound le) -SF1 to SF15 (3MB in total, 2MB/le) -
Registering sound
sequences
Sound number - SS1 to SS20 SS1
Sound sequence
name
- Up to 24 alphanumeric characters -
Step - 1 to 10 1
Sound source Sound le (Select from the registered ones.) -
Repeat times 1 to 10 1
Registering daily
chime schedule
Schedule number - DS1 to DS10 DS1
Schedule name - Up to 24 alphanumeric characters -
Chime time - Hour: 0 to 23
Minute: 0 to 59
Second: 0 to 59
-
Sound source - Sound le (Select from the registered
ones.)
/Sound sequence (Select from the
registered ones.)
/External sound source (1 or 2)
-
Zone number - (Select from the registered ones.) -
Chime priority - Normal/Priority/Urgent Normal
Chime schedule
setting
Weekly schedule (Repeat setting) Every week/Every other week Every week
Schedule start date From the current day to 1 year ahead -
Schedule end date From the start day to 1 year ahead -
(Chime schedule) None/DS1 to DS10 (for each day of the
week)
None
Individual schedule (Date) From the current day to 1 year ahead -
Daily chime schedule (Select from the registered ones.) None
Chime time Hour: 0 to 23
Minute: 0 to 59
Second: 0 to 59
-
Sound source Sound le (Select from the registered
ones.)
/Sound sequence (Select from the
registered ones.)
/External sound source (1 or 2)
-
Zone number (Select from the registered ones.) -
Chime priority Normal/Priority/Urgent Normal
Schedule download - (Download the chime (and transfer)
schedule data in CSV format.)
-

7
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Title Sub title Item Sub item Setting range Default
Transfer setting Registering
schedule transfer
setting
Schedule number - DT1/DT2 DT1
Schedule name - Up to 24 alphanumeric characters -
Call transfer time - Hour: 0 to 23
Minute: 0 to 59
(Set to the Start time and End time
individually.)
-
Transfer schedule
setting
Weekly schedule (Repeat setting) Every week/Every other week Every week
Schedule start date From the current day to 1 year ahead -
Schedule end date From the start day to 1 year ahead -
(Transfer schedule) None/DT1/DT2 (for each day of the
week)
None
Individual schedule (Date) From the current day to 1 year ahead -
Daily transfer schedule (Select from the registered ones.) None
Call transfer time Hour: 0 to 23
Minute: 0 to 59
(Set to the Start time and End time
individually.)
-
Timer setting - Call Normal/Priority/Urgent 10 to 600 (sec.), 0 (Unlimited)
Normal: 30 (sec.)
Priority: 90 (sec.)
Urgent: 0
(Unlimited)
Communication In Local (local system only) 30 to 600 (sec.) 60 (sec.)
Paging - 30 to 600 (sec.) 60 (sec.)
Monitor - 10 to 600 (sec.) 60 (sec.)
Scan monitor:
Switching
- 5 to 60 (sec.) 5 (sec.)
Contact output External sound source 1 10 to 300 (sec.) 30 (sec.)
External sound source 2 10 to 300 (sec.) 30 (sec.)
Door release - 0 to 300 (sec.), (0: Released while
holding the Door release button
pressed.)
10 (sec.)
Time and date
setting
- Set current time Manual setting Year: 2009 to 2099
Month: 1 to 12
Day: 01 to 31
Hour: 00 to 23
Minute: 00 to 59
Second: 00 to 59
(Internal time
of the central
control unit)
Synchronized with PC - -
NTP Synchronized with NTP server ON/OFF OFF
NTP server*1IP address or domain name -
NTP port number*10 to 65535 123
(UTC time zone*1)
Hour difference*1
-12 to +13 (h) 0
(UTC time zone*1)
Minute difference*1
-45/-30/0/+30/+45 (m) 0
Synchronize interval*11 to 240 (h) 24 (h)
Daylight savings time - ON/OFF OFF
Starts*2Month JAN to DEC (M) JAN
Day (Week) 1st to 4th (W)/The last 1st
(Day) Sunday to Saturday Sunday
Hour (Hour) 0 to 23 (h) -
(Minute) 0 to 59 (m) -
Ends*2Month JAN to DEC (M) JAN
Day (Week) 1st to 4th (W)/The last 1st
(Day) Sunday to Saturday Sunday
Hour (Hour) 0 to 23 (h) -
(Minute) 0 to 59 (m) -
Hour difference*20 to 12 (h) 1
Minute difference*20/30/45 (m) 0
Setting le Downloading
setting data
-- - -
Uploading setting
data
-- - -
*1: Available only when [Synchronized with NTP server] is set to ON.
*2: Available only when [Daylight savings time] is set to ON.

8
STARTING UP THE SYSTEM
Before making the system settings, conrm that a PC is connected to the central control unit (IS-CCU). The system settings are made
on the PC by accessing the web browser for the settings incorporated with the central control unit (IS-CCU).
System requirements for PC
Your PC and operating environment must meet the following system requirements to make the settings.
Network 10BASE-T Ethernet
Web browser Internet Explorer 6.0 or later (with Internet Options SSL 3.0 enabled)
Starting up the system
Connect a PC to the central control unit.
1
[When connecting a PC to the central control unit
via a router]
CAT5e/6
(Straight-through cable)
CAT5e/6
(Straight-through
cable)
100m (330')
10BASE-T
/100BASE-TX
100m (330')
10BASE-T
PC
RJ45 RJ45
RJ45
RJ45
Router
NOTES:
Select this connection method when you will acquire an IP
•
address automatically by DHCP.
Do not select this connection method if your router does not
have a DHCP server function.
Be sure to connect the CAT5e/6 cable to the LAN ports of both
•
units.
[When connecting a PC to the central control unit
directly]
CAT5e/6 (Crossover cable)
100m (330')
10BASE-T
PC
RJ45
RJ45
NOTES:
Select this connection method when using a static IP address.
•
When connecting a PC to the central control unit directly, use
•
an Ethernet crossover cable.
The IP address of central control unit is set to (192.168.0.30)
•
as default. Change the IP address of your PC if needed.

9
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Press down the "I" side of POWER switch to turn on
2 all the control units in the system.
Start up the PC, and then open the browser window.
3
Enter the
4 static IP address (https://192.168.0.30/)
or the IP address assigned by DHCP to access the
web browser for settings.
If you do not know your IP address assigned by DHCP,
*
run “IS_IPSEARCH.exe” from the supplied CD-ROM,
and then search for it.
The login window of the web browser is displayed.
Log in to the system by setting the following items.
5
ID
•
Enter “aiphone.”
Password
•
Enter “aiphone.”
Login
•
Click Login to display the setting window.
Setting the system conguration
[System conguration]
After logging in to the system, [System conguration] window
appears rst.
First of all, make the setting on this window before starting the
system settings.
Select your system between “Local system” and
1 “Standard system (IP system).”
Click
2 Temporarily stored to save the setting result
temporarily. (→P. 10)
Start the system settings by selecting a setting title in
3 the table of contents on the left side of the window.
Go to the next page.
Conrm that the following LEDs
*
operate as shown below.
POWER switch
Press down "I" side to turn on the
•
unit.
Press down "O" side to turn off the
•
unit.
Lights up.
Blinks
(When the system settings have
nished correctly, this LED turns from
blinking (initializing) to lighting.)

10
MAKING THE SYSTEM SETTINGS
The basic setting procedure
When you have logged in to the system, the setting window appears. You can make the settings on this window.
Make sure to refer to the on-screen instructions and comments displayed on each window when you make the settings.
*
Depending on the PC and its OS or environment, the display may differ.
*
<Setting window example>
The setting procedure
Click a title in the table of contents on which you wish to make the settings.
1
The setting window of the title is displayed.
Make the settings on the setting items individually.
2
When you have nished making the settings on the current window, click
3 Temporarily stored to save the setting
results temporarily.
If you wish to cancel the setting results you have made, click a title in the table of contents or “Refresh” in the web browser
*
menu. (If you change the current window to another without storing the setting results temporarily, a pop-up window appears
asking if you want to store the results temporarily or not.)
Repeat step
4 1to 3to make the settings on the other titles.
Setting contents display area
The setting items of the selected setting title and their
details are displayed here.
Table of contents
The setting titles are listed here.
Click the title on which you want
to make the settings to display the
corresponding setting window.
Instructions area
The instructions for each setting item
is displayed here.
Temporarily stored
Click this to save the current setting results
temporarily.
This temporary storing will not update the*
system with the new setting results. To update
the system, click the title “Updating the system”
and follow the necessary procedure.

11
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Making network settings [Network setting]
Make the settings for network according to your
requirements.
Click
1 Network setting in the table of contents.
Make the settings on the following items displayed in
2 the setting window.
Selecting the network setting method
Set a (static) IP address to this unit. Select the method for
acquiring a (static) IP address between [DHCP] and [Static
IP Address].
[DHCP]:
•
Check this when you will acquire an IP address with
DHCP.
A DHCP server (or a router) is required to acquire
*
an IP address with DHCP. A router may not have
the setup function depending on some models. For
information about setting a router, see the instruction
manual for the router.
[Static IP Address]:
•
Check this when you do not use a DHCP server (or
a router) or connect the PC to the central control unit
directly, and then enter the static IP address and subnet
mask.
It is required to enter the static IP address and
*
subnet mask.
[Unit name]:
•
Enter a name for this unit. (This name will not be used
when operating the system.)
NOTE:
The items that cannot be changed or selected are grayed out.
Click
3 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
Setting the administrator ID and password
[Administrator setting]
We recommend that you change the administrator ID and
password from default to unique ones for security purposes.
“aiphone” is preset as the default for both ID and password.
*
Click
1 Administrator setting in the table of contents.
Make the settings on the following items displayed in
2 the setting window.
[New administrator ID]:
•
Enter the new ID.
[Current Password]:
•
Enter the current password.
[New Password]:
•
Enter a new password.
[New Password (Re-type)]:
•
Enter the new password again.
Click
3 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
The following shows the setting procedure for the items of each title.
Refer to “SETTING LIST” (→P. 4-7) for details about the settings. Make the settings by also referring to the on-screen instructions.

12
Registering areas
[System setting – Area registration]
Required
Register areas for separating stations in the system. The
number to which a name is entered is registered as an area
number. Up to 99 areas can be registered.
Click
1 Area registration in the table of contents.
Enter an area name in the cell for the area number 01.
2
The gures under "Number" in the tables means the area
*
numbers.
Enter area names in the cells for other numbers to
3 register more areas.
Click
4 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
NOTES:
Be sure to register at least one area to the area number 01.
•
(“1” is entered in the cell for the area number 01 as default.)
A call number displayed on the master station monitor consists of
•
an area number plus a station number.
Registering zones
[System setting – Zone registration]
Register zones for paging (transmitting announcements and
chime). The number to which a name is entered is registered
as a zone number. Up to 99 zones can be registered.
* Zones are groups of stations designated for paging and chime
paging.
Click
1 Zone registration in the table of contents.
Enter a zone name in the cell for the target zone
2 number.
The gures under "Number" in the table means the zone
*
number.
Enter zone names in the cells for other numbers to
3 register more zones.
Click
4 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
Registering control units [System setting
– Control units composition]
Register all the control units connected to the central control
unit.
Click
1 Control units composition in the table of
contents.
Click to check the radio button under "Connected" for
2 the unit you will register.
Click
* Connection check to conrm the connected units.
Connected: yellowish green
Not connected: gray
Shows a port no. of the central control unit to connect with
a room sub control unit or add-on control unit.
Shows the ID setting of the room sub control unit or add-
on control unit set by the ID setting switches. (Refer to the
INSTALLATION MANUAL for details.)
Click
3 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.

13
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Registering stations and PA outputs
[System setting – Registering stations]
Register all the stations and PA outputs connected in the
system, and set the area, station no., station name (or PA
output name) and type of station (for sub stations) to them.
Click
1 Registering stations in the table of contents.
Set the area, station no., station name and type of
2 station (for sub stations) to the target stations, and
enter names to the target PA outputs.
Setting the station no. is required.
*
Shows a port no. of the control unit to connect with a
*
station.
It is required to enter a name to the target PA
*
output when an external unit is connected to the
corresponding PA output terminals.
For a cell with the
* mark, select the target one from the
pull-down menu.
Do not set stations with the same number in an area.
*
Other buttons
Connection check
•
Click to conrm the connected units.
Connected: yellowish green
Not connected: gray
Station type error: pink
[Collective setting]:
•
The following buttons are used to make the settings to all
the checked stations at one time.
NOTE:
Be sure to check all the target stations before using these
buttons.
Area
•
Click to set the same area number to all the checked
stations.
Station number
•
Click to assign sequential numbers to all the checked
stations from top to bottom. The number you enter will
be set as the rst number and will be assigned to the top
station of the ones checked. Other checked stations will
be numbered sequentially.
Station name
•
Click to assign the same station name and sequential
numbers to all the checked stations from the top down.
Enter a station name only.
Station type
•(sub stations)
Click to set the same station type to all the checked sub
stations.
How to select multiple stations
○ Click to check the stations and PA outputs you will
register.
○ By clicking the button for the control unit, all the stations
and PA outputs connected to it are checked or canceled.
○ By clicking the button on the top of the list, you can
check or cancel all the stations and PA outputs on the
list.
Click
3 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.

14
Making detailed settings to stations and
control units
[System setting – Advanced station settings]
Make detailed settings for the registered stations and control
units. The settings can be made to a station or control unit
individually, or multiple stations of the same type at a time. The
setting items differ from the station or control unit type. First
select a station (or stations) or control unit, and then open the
“Advanced settings” window to make the settings.
Basic setting procedure
Click Advanced station settings in the table of
contents.
Click to check the station(s) or control unit where detailed
settings are to be made.
Multiple stations of the same type can be set together.
*
(Control units should be set respectively.)
All stations of the same type can be selected by clicking the
*
corresponding button under [Select all by type].
Click Advanced settings .
The “Advanced settings” window for the selected station type
or control unit opens.
Make the settings in the displayed windows.
For door and room sub stations
The right column of this page
For master stations
P.15
For control units
P.16
When you have nished making all the detailed settings:
Click Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made, click
*
a title in the table of contents or “Refresh” in the web browser
menu.
Making detailed settings to door
stations or room sub stations
NOTE:
Make the settings to door stations or room sub stations
respectively. You cannot select a video door station, audio door
station and a room sub station at the same time.
The following setting item buttons are displayed in the
“Advanced settings” window.
Click one of the buttons
* A,Band Cto open the
corresponding setting window, and then make the
settings in the displayed window(s). See the detailed
instructions for A,Bor Cbelow.
Click
* Close to close the current window and return to
the previous window.
A Settings on [Called stations] setting window
Set the master station(s) that is (are) to be called from the
selected station(s).
Up to 20 master stations can be set.
*
Select the “Call priority” from the pull-down menu.
1
Click
2 Reference to open another window, then check
the target master stations, and then click Close to
return to the previous window.
The selected master stations are added and
displayed in the list.
To delete a station (or stations) from the list, check the
*
target station(s) in the list and click Delete .
Repeat step
3 1and 2to add more master stations.
Click
4 Close to close the current window and return to
the previous window.
A
B
C
(room sub stations only)

15
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
B Settings on [Contact input] window (for room
sub stations only)
Make settings for contact input.
[Contact type]:
•
Select either Normally open (NO) or Normally closed (NC).
[Call priority/Answering the page]:
•
You can select the action of the station when detecting
input between ‘calling with appropriate priority’ and
‘answering the page’.
Select “Normal”, “Priority”, “Urgent” or “Answering the
page”.
Close
•
Click this to close the current window and return to the
previous window.
C Settings on [Other] window
[Transmit volume boost at PTT]:
•
Select whether to increase the press-to-talk sound
volume transmitted to the stations (ON) or not (OFF).
[Camera zoom image preset] (video door stations
•
only):
Select the default of camera’s Zoom/Wide function at
calling from the 9 zoom positions and "0" (wide) from the
pull-down menu.
[Call acknowledge tone on/off]:
•
Select whether to sound the call acknowledge tone of
door station or room sub station (ON) or not (OFF).
[Backlight adjustment] (video door stations only):
•
Select the method of adjusting the backlight in the
daytime between “Exposure +” and “Exposure –.”
[Speaker] (room sub stations only):
•
Select the speaker to be used between “Built-in speaker”
and “External speaker.”
When “External speaker” is selected, no sound will be
*
output from the built-in speaker.
Close
•
Click this to close the current window and return to the
previous window.
About the priority
When receiving two or more functions (communication, calling,
paging, monitoring, etc.) at the same time, depending on the
priority setting, the order of priority for them is as follows.
Priority Setting Function
1 (high) [Urgent] Communication, calling,
paging, chime paging
2[Priority]
3[Normal]
4 (low) - Monitoring, scan-monitoring
Making detailed settings to master
stations
The following setting item buttons are displayed in the
“Advanced settings” window.
Click either the button
* Dor Eto open the
corresponding setting window, and then make the
settings in the displayed window(s). See the detailed
instructions for Dor Ebelow.
Click
* Close to close the current window and return to
the previous window.
D
Settings on [Stations to be scan monitored]
window
Set the scan-monitoring target sub station(s).
Up to 20 sub stations can be set.
*
Click
1 Reference to open another window, then select
the target stations, and then click Close to return to
the previous window.
The selected stations are added and displayed in the
list.
To delete a station (or stations) from the list, check the
*
target station(s) in the list and click Delete .
Repeat step
2 1to register more stations.
Click
3 Close to close the current window and return to
the previous window.
E Settings on [Other] window
[Master station function: paging, chime, monitor,
•
door release, and remote site call]:
Select whether to enable the following functions of
master station (ON) or not (OFF).
Starting paging
•
Starting chime paging
•
Monitoring/scan-monitoring
•
Releasing door
•
Remote site call (standard (IP) system only)
•
Close
•
Click this to close the current window and return to the
previous window.
D
E

16
Making detailed settings to the central control
unit, add-on control unit(s) or room sub
control unit(s)
NOTE:
Make the settings to the central control unit, add-on control
unit(s) or room sub control unit(s) respectively. You cannot select
multiple control units at the same time.
The following setting item buttons are displayed in the
“Advanced settings” window.
Click either the button
* For Gto open the
corresponding setting window, and then make the
settings in the displayed window(s). See the detailed
instructions for For Gbelow.
Click
* Close to close the current window and return to
the previous window.
F Settings on [Contact input] window (for central
control unit only)
Set the input method to each of the CONTACT INPUT
terminals (1 to 4).
Select the input terminal from S1 to S4 from the pull-
1 down menu.
[Contact type]:
2 Select either Normally open (NO) or Normally closed
(NC).
[Trigger condition]:
3 Select [None], [Broadcast chime] or [Stop chime] as
the trigger condition. When an input is detected, the
selected action is triggered.
[None]:
•
None will be triggered if an input is detected.
[Broadcast chime]:
•
Chime paging to the designated zone is triggered if an
input is detected.
[Stop chime]:
•
The currently-transmitted chime is stopped if an input is
detected.
Only when [Broadcast chime] is selected, the following
*
items are valid.
[Sound source]:
•
Select either [Internal sound source] or [External
sound source] as the source of chime. When [Internal
sound source] is selected, select a sound le or
sequence from the registered ones in the list.
(You need to register sound les and/or sound
sequences in advance. (→P. 17-18))
When [External sound source] is selected, select
either “External sound source 1” or “External sound
source 2.”
[Chime priority]:
•
Select the priority of chime paging from among
“Normal”, “Priority” and “Urgent.”
[Zone name]:
•
Select the target zone of chime paging from the
registered ones in the list.
Repeat step
4 1to 3to make the settings to other
terminals.
Click
5 Close to close the current window and return to
the previous window.
G Settings on [Contact output] window
Set the trigger condition to each of the CONTACT OUTPUT
terminals .
Select an output terminal from the pull-down menu.
1
Select from L1 to L8 for the central control unit, and
*
select from L1 to L4 for the add-on control unit and room
sub control unit.
[Contact type]:
2 Select either Normally open (NO) or Normally closed
(NC).
[Trigger condition]:
3 Select the action as the trigger condition from among
the following. When the selected action is detected,
output is triggered.
[None]:
•
No output will be triggered.
[Calling notice]:
•
Set ON or OFF for “Normal”, “Priority” or “Urgent.”
[Door release]:
•
Select one of the registered sub stations in the list
to which an electric door strike is connected. (Click
Reference , and then select the target station.)
[External sound source]:
•
Select either “External sound source 1” or “External
sound source 2” connected to the central control unit.
[PA output]:
•
Select from among “PA output 1” to “PA output 4”
connected to the control unit.
Repeat step
4 1to 3to make the settings to other
terminals.
Click
5 Close to close the current window and return to
the previous window.
(central control unit only)
F
G

17
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Registering stations and PA outputs to zones
[
System setting – Zone setting]
Assign stations and PA outputs to the registered zones.
Click
1 Zone setting in the table of contents.
Select a zone from the pull-down menu.
2
Click
3 Reference to display all the stations registered
to the system.
Another window opens and the registered stations are
displayed in the list.
Check to select the target stations.
4
Select stations in the following ways.
Select stations by checking one by one.
•
All stations of the same type can be selected by
•
clicking the corresponding button under [Select all by
type].
By clicking the button for the control unit, all the
•
stations connected to it are checked or canceled.
By clicking the button on the top of the list, all the
•
stations are checked or canceled.
Click
5 Close after you have nished selecting the
stations.
In the previous window, the selection results are displayed
in the list.
When canceling a registered station, check the station in
*
the list, then click Delete .
Register PA outputs in the same way as the stations.
*
Click
6 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
Registering sound les for chime
[Chime setting – Registering sound source]
Register sound data as the source of each chime. Copy MP3-
format sound les onto the PC in advance. (Only MP3 les can
be registered in the system.)
* Up to 3MB of the total amount of les can be registered.
* Use sound les compliant with the specications below.
Click
1 Registering sound source in the table of
contents.
Click
2 Add .
Another window opens.
Click
3 Browse... and select a sound le on the PC.
Click
4 Upload to save.
When uploading the le is completed successfully, the
current window closes. In the previous window, the
selection result is displayed in the list.
If a small-size sound le is registered, a le size different
*
from the actual one may be displayed.
Repeat step
5 2to 4 to register more sound les.
If you wish to delete a sound le, check it in the list, and
*
then click Delete .
Sound le specications
Item Recommended value
File name Up to 24-single byte alphanumeric
characters
File format MP3*1
Bit rate 64 kbps
Sampling frequency 44.1 kHz
Channels 1 ch (monaural)
Maximum total data size 3MB in total, 2MB/le
*1: MP3-format sound les with tags may not be played with this
system. Before registering an MP3-format sound le, delete the tag
from the le.

18
Registering sound sequences
[Chime setting – Registering sound sequences]
Register sound sequences for chime.
Up to 20 sequences can be registered.
*
Click
1 Registering sound sequences in the table of
contents.
[Sound number]:
2
Select the sound number to register a sound sequence
from the pull-down menu.
[Sound sequence name]:
3
Enter the name of sound sequence.
Click
4 Add to add sound les to the sound sequence.
Another window appears.
[Step]:
5
Select an unused step number from the pull-down menu.
If the selected step number is already used, it can be set
*
with a new sound source and the old and subsequent
ones are renumbered with the following numbers.
If an unused number exists before the number you
*
selected, the unused number is re-selected automatically.
Up to 10 steps can be used.
*
[Sound source]:
6
Select a sound le from the registered ones and set the
repeating time (from 1 to 10) of the sound.
When you have nished the setting on this window,
7 click Close .
In the previous window, the registered sound les are
displayed in the list.
Repeat step
8 2to 7to register more sound sequences.
Other buttons
Edit
•
If you wish to modify, check the le in the list, and then
click Edit .
Delete
•
When deleting an added sound le, check the le in the
list, and then click Delete .
Click
9 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
Registering daily chime schedule
[Chime setting – Registering daily chime schedule]
Up to 10 daily schedules can be registered.
Click
1 Registering daily chime schedule in the table
of contents.
[Schedule number]:
2 Select the schedule number to register the daily
schedule from the pull-down menu.
[Schedule name]:
3 Enter the name of daily schedule.
Click
4 Add to add programs.
Another window appears.
[Chime time]:
5 Set the starting time (hour, minute and second).
[Sound source]:
6 Check [Sound le], [Sound sequence] or [External
sound source], and select a le, sequence or external
sound source from the pull-down menu.
[Zone number]:
7 Select the target zone for transmitting chime from the
pull-down menu.
[Chime priority]:
8 Select the priority of transmitting chime from among
“Normal”, “Priority” or “Urgent” from the pull-down
menu.
When you have nished the settings on this screen,
9 click Close .
In the previous window, the added programs are displayed
in the list.
10
Repeat step 2to 9to add more programs.
Other buttons
Edit
•
If you wish to modify a program, check the program in
the list, and then click Edit
Delete
•
When deleting a program, check the program in the list,
and then click Delete .
11
Click
Temporarily stored
to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.

19
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Setting chime schedule
[Chime setting – Chime schedule setting]
You can set a weekly chime schedule or individual daily
schedule.
* The settings can be made to 1 year ahead.
Click
1 Chime schedule setting in the table of
contents.
Make the settings by clicking
2 Weekly schedule ,
Individual schedule and Schedule download
respectively to open the corresponding window.
Individual schedule
* should be clicked after the target
date is clicked on the calendar.
Make the settings in the displayed window(s).
3
See the detailed instructions for H, Ior Jon the
right column of this page.
After the setting is nished on the corresponding
4 window, click Close to close the window.
Calendar and setting status can be checked for the
selected month.
The registered daily chime schedules are identied by
colors and shown on the calendar.
Click
5 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
H Settings on [Weekly schedule] setting window
Select either [Every week] or [Every other week].
1)
Set the schedule start and end dates.
2)
The monthly calendar is displayed by clicking
*
Refer calendar and you can select the start and
end dates.
If necessary, you can change the month by clicking
*
or .
Set one of the registered daily chime schedules or no
3) schedule to each day of the week. (Select one from the
pull-down menu.)
I Settings on [Individual schedule] setting window
Set an individual schedule to the target date.
[Individual schedule] setting window will not open if you
*
have not selected the target date on the calendar in the
[Chime schedule setting] window.
If necessary, you can change the date by clicking
1) or
repeatedly.
[Daily chime schedule]:
2) Select one of the registered daily chime schedules or
no schedule, from the pull-down menu.
If necessary, modify a registered schedule or register a
3) new schedule.
To register a new schedule:
•
Click Add .
Another window opens. In this window, you can set
[Chime time], [Sound source], [Zone number] and
[Chime priority].
When the settings have nished, click Close to
close this window.
Repeat this procedure to add more schedules.
*
To modify a registered schedule:
•
Check the schedule you wish to modify, and then
click Edit .
Another window opens. Change the settings in this
window.
When nished modifying, click Close to close this
window.
When modied, [Daily chime schedule] changes to
*
“Individual schedule.”
To delete a registered schedule:
•
Check the schedule you wish to delete, and then
click Delete .
When deleted, [Daily chime schedule] changes to
“None”.
JDownloading chime schedule data
You can store the chime schedule setting data in CSV
format onto a PC.
The data includes the transfer schedule setting data
*
along with the chime schedule setting data. (→P. 20)
H
I
J

20
Registering daily transfer schedule
[Transfer setting – Registering daily
transfer schedule]
You can set the schedule for transferring calls to other master
stations automatically. The schedules registered on this setting
are used when making a transfer setting on a master station.
Up to 2 daily schedules can be registered.
Click
1 Registering daily transfer schedule in the
table of contents.
[Schedule number]:
2 Select the schedule number DT1 or DT2 from the
pull-down menu.
[Schedule name]:
3 Enter the name of daily schedule.
[Call transfer time]:
4 Set the [Start time (hour and minute)] and [End time
(hour and minute)] of transferring.
Click
5 Temporarily stored to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
Setting transfer schedule
[Transfer setting – Transfer schedule setting]
You can set a weekly transfer schedule and individual daily
schedule.
The settings can be made 1 year ahead.
*
Click
1 Transfer schedule setting in the table of
contents.
Make the settings by clicking
2 Weekly schedule
and Individual schedule respectively to open the
corresponding window.
Individual schedule
* should be clicked after the target
day is clicked on the calendar.
Make the settings in the displayed window(s).
3
See the detailed instructions for Kor Lon the
next page.
After the setting is nished on the corresponding
4 window, click Close to close the window.
Calendar and setting status can be checked for the
selected month.
The registered daily transfer schedules are
identied by colors and shown on the calendar.
Click
5
Temporarily stored
to save the current setting
results temporarily.
If you wish to cancel the setting results you have made,
*
click a title in the table of contents or “Refresh” in the
web browser menu.
K
L