Code Clean Notus Series User manual

Page 1of 4
NOTUS HAND DRYER USER MANUAL
5-YEAR LIMITED WARRANTY
This product is warranted to be free of manufacturing defects for five (5) years from the date of purchase from the factory.
This warranty explicitly excludes normal wear and tear on the units, as well as faulty installation, accident, misuse, or
vandalism.
In the event of a machine failure, the owner shall have one of the following options:
a. The owner can return the defective product to the manufacturer with a return authorization number, postage prepaid
and the manufacturer shall repair said product within a reasonable time free of charge, provided that said product is
returned within the stated period above from the date of original shipment from the factory in Brant, ON and that said
defect is not due to faulty installation, accident, misuse or vandalism; or
b. The Owner can return the defective product to a factory approved service/repair center, postage prepaid and the repair
center shall repair the product within a reasonable time provided that said product is returned within the stated period
above from the date of original shipment from the factory in Brant, ON and provided that said defect is not due to
faulty installation, accident, misuse or vandalism. Please note that the service center does reserve the right to apply a
labour charge for services rendered; or
c. The Owner may notify the manufacturer by telephone or in writing of the defect and within a reasonable time, the
manufacturer shall send a suitable replacement part to remedy said defect and the owner shall be charged for said part
at the current price level. The owner may return the defective part with a return authorization number to the
manufacturer, postage prepaid, along with the serial number of the defective product and the manufacturer will then
issue to the owner a full credit for the repair part, including outgoing postage (within Canada only). Said remedy is
available only within the stated period stated above from the date of original shipment of the product from the
manufacturer’s factory in Brant, ON and provided that said defect is not due to faulty installation, accident, misuse or
vandalism.
Any implied warranties of merchantability or fitness for a particular purpose are hereby limited to the duration of the
express written warranty contained in paragraph one (1); namely, five (5) years from the date of shipment from the
Manufacturer’s factory in Brant, ON.
There are no other warranties and remedies except as contained herein.
WARNING:
For proper electrical connections, check your local building codes. Your hand dryer must be installed by a qualified,
licensed electrician.
If you do not use this hand dryer properly or follow the safety guidelines carefully, it could lead to serious personal injury or
property damage.

Page 2of 4
Do not leave shell off the hand dryer. Do not let children hang from the hand dryer. Do not allow the hand dryer to get
wet. Do not use in a wet environment, for example near the bathroom where it may get direct water and the places where
the condensation may form. Do not modify or disassemble the unit unnecessarily. Otherwise this may cause fire, electric
shock, the unit to malfunction, property damage and/or personal injury.
Use dedicated circuits with the rated power required. Do not wire this hand dryer into the lighting circuit. Machines are
intended to be permanently connected to power a supply and must have a reliable ground connection. If power tolerance
is over +/- 10%, there will be a breakdown. If using the incorrect power supply, fire, electric shock and/or machine
malfunction will result. If using together with other appliances, the circuit may generate abnormal heat leading to fire.
Power must be cut off when maintaining to prevent the risk of electric shock.
Air filter must be installed.
If the machine presents abnormal working conditions or stops working completely, cut off power supply at the breaker to
prevent any accidents or electrical shock.
Make sure electricity is switched off at the main panel before installing, maintaining or cleaning this hand dryer. Dryer must
be installed in accordance with current local wiring and building regulations.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
For additional protection, the installation of a residual current device (RCD) having a rated residual operating current not
exceeding 30 mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.
ENVIRONMENTAL PROTECTION
electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your
local authority for recycling advise.
SAFETY
Troubleshooting and internal maintenance must be performed by qualified service personnel. Do not use any power wash
equipment for cleaning on or near this unit. Do not use the hand dryer for drying hair. Do not obstruct air inlets or outlets.
CLEANING / MAINTENANCE
To clean the outside of the hand dryer, shut off power at the breaker and remove cover by unscrewing the 2 bolts, one from
each side with the wrench provided with each dryer. Use a small, soft brush or cloth to gently clean the cover and other
parts.
Internally, inspect the inside of the dryer and clean as required at least once per year or if performance diminishes. Heavier
usage or an environment that contains excessive lint, dust or other particles, requires more frequent cleaning. Lint on the
air inlet, prefilters or other internal parts of the dryer will reduce efficiency and shorten the life of the working parts.
To clean the prefilter, remove it from the machine, rinse it with water and dry. Then, re-install.
SPECIFICATIONS:
Voltage
100-130V or 220-240V
Motor
Brush Motor
Phase
Single Phase
Sensing Distance
15-20 CM
Input
1400-1650 W
Protection Class
IPX1
Wind Speed
60 or 105 M/S
Unit Size
295 x 170 320 MM
Heating Power
800-950 W
Net Weight
4.5 KG

Page 3of 4
INSTALLATION INSTRUCTIONS
1. Disconnect the power from the breaker where the dryer is planning to be installed.
2. Use the wrench supplied to remove the 2 cover mounting screws and lift cover to expose base plate.
3. If electrical wiring entry is to be made from the rear, remove the appropriate pre-formed knockout on the base plate. If
entry is to be made from the bottom, knock out the pre-formed area on the cover for your supply connection. A rigid
conduit must be used.
4. Select the appropriate mounting height for dryer
(Table to the left) and fasteners provided. There should be
no obstruction between the hand dryer and the floor. If
mounting over a countertop, distance from counter to
dryer must be 20” (508 mm) minimum.
CAUTION: Do not use Base Plate as a guide when drilling.
Make sure no pipe work (gas, water, air) or any electrical
cables or wires are located directly behind the area to be
drilled.
5. Attach wall mounting plate at the four corners to smooth wall.
6. Identify the voltage of your dryer from the rating sticker of on the unit. Then connect to a dedicated branch circuit not
exceeding 15 Amp.
7. Secure electrical wiring to terminal block as indicated by the schematic on the wall mounting plate below the terminal
block. Dryers should be installed per local code requirements.
8. Carefully replace Cover using the 2 screws previously removed in step 2. Restore power and test for proper operation.
In multiple installations, make sure the serial number marked on the inside matches the cover number.
9. It is highly recommended that a bead of silicone sealant be placed around the outside of the cover at the wall to protect
dryer from internal corrosion caused by wash water and cleaning solutions.
10. Return wrench and Owner's Manual to owner
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer.
B. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to the service panel.

Page 4of 4
DRYER COMPONENTS:
WIRING BREAKDOWN: