V-ZUG WT-ATLWPZ 958 User manual

Installation instructions
Heat pump dryer
One-family household
J958.370-0
29.4.10 ITH
1
For Service and Spare Part Information please contact:
Manfred Schulz, Technical Manager
V-ZUG AUSTRALIA PTY LTD, c/o C.W. Stirling
6th floor 90 William Street, Melbourne, VIC 3000
[email protected]
Tel/ Fax [phone], Mob [phone]
These installation instructions apply to the model: 958
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
Transport
The appliance is only to be transported in the upright position! Transporting it in any other position will result in damage to the
appliance! When carried carefully, without being shaken, the appliance may be tilted to the left by a maximum of 90° (viewed
from the front).
The appliance must be allowed to stand in the standard operating position for about 2 hours before using the heat pump. Failure
to observe this can result in damage to the appliance.
Front
Front
Front Back
Front,
upside down Side

Installation instructions
Heat pump dryer
One-family household
J958.370-0
29.4.10 ITH
2
For Service and Spare Part Information please contact:
Manfred Schulz, Technical Manager
V-ZUG AUSTRALIA PTY LTD, c/o C.W. Stirling
6th floor 90 William Street, Melbourne, VIC 3000
[email protected]
Tel/ Fax [phone], Mob [phone]
AOpen the appliance door and the cover.
– The identification plate is located bottom right behind the cleaning cover.
The necessary installation accessories are located in the drum.
Installation plate (W5.0542)
incl. screw material (S) and double-sided adhesive tape
The room must be well ventilated to ensure that the room temperature does not exceed 35 °C.
If the volume of the room in which the appliance is located is at least 20 m³ when closed:
Condensation may form on thermal bridges!
The room must be aired (by opening the door to or a window in the room) between consecutive drying programmes!
If the volume of the room in which the appliance is located is less than 20 m³:
There must be air inlet and outlet openings (open window, ventilation grille or slits in the door, ventilation system) to the adjacent room
or to the outside.
ARaise the appliance slightly at the front and pull it forward, away from the installation plate.
ASecure the installation plate to the location you wish to install the appliance using 4 screws. On smooth and clean floors, you can
affix the installation plate (double-sided adhesive tape supplied).
ADampen the mounting slots on the installation plate with water.
Identification plate
Installation accessories supplied
Article Article no. Number See installation step
Condensate drain kit W5.5845 1 4. Connect condensate drain
Room conditions / ventilation
Do not obstruct the appliance’s ventilation slits to ensure that there is an ample supply of air.
The extracted air must not be fed into a chimney which is used for exhausting fumes from appliances burning gas or other fuels.
The room temperature should be kept as low as possible to ensure the economic running of the appliance. Critical is a room
temperature of 35 °C and over. This prolongs the duration of the programmes.
Installation
Work steps 1–5must be carried out in full in the order specified.
1. Positioning the installation plate
Use the installation plate to install the appliance. This plate fixes the appliance in position (for both free-standing appliances
and appliances placed in a niche).
The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite to that of the
appliance, in such a way that a full opening of the appliance door is restricted.
S

Installation instructions
Heat pump dryer
One-family household
J958.370-0
29.4.10 ITH
3
For Service and Spare Part Information please contact:
Manfred Schulz, Technical Manager
V-ZUG AUSTRALIA PTY LTD, c/o C.W. Stirling
6th floor 90 William Street, Melbourne, VIC 3000
[email protected]
Tel/ Fax [phone], Mob [phone]
Free-standing position
Positioning in a niche
ACentre the installation plate in the niche.
If a tumble dryer and a washing machine are positioned side by side, keep a distance of min. 5 mm between installation plates
and min. 3 mm to walls.
* This only applies if no plumbing fittings are to be installed behind the appliance.
Add another 20 mm if the condensed water hose leads away to the left.
The heat given off from the rear of the appliance must be lead out of the niche. For this the rear cover parts must be removed.
Mount ventilation grille P33.002 and ensure there is a supply of fresh air via the connection opening.
min. 3 597
595
50
505
min. 550 *
min. 5 min. 5
min. 600 *
Niche depth
min. 600
Niche width
Cut-out for lateral
connections, to the
left or right side
min. 100 × 100 mm
min. 50
min. 1705
Niche height
400 cm²
Ventilation grille
min. 860
Niche height
400 cm²
Ventilation grille

Installation instructions
Heat pump dryer
One-family household
J958.370-0
29.4.10 ITH
4
For Service and Spare Part Information please contact:
Manfred Schulz, Technical Manager
V-ZUG AUSTRALIA PTY LTD, c/o C.W. Stirling
6th floor 90 William Street, Melbourne, VIC 3000
[email protected]
Tel/ Fax [phone], Mob [phone]
ARoughly adjust the rear adjuster feet.
ATo ensure smooth, fault-free operation, the appliance must be perfectly vertical. Use a
spirit level to position the appliance.
ASlide the appliance in. Finely adjust the front adjuster feet until all 4 feet are standing
firmly on the floor.
– The appliance must not wobble.
AInformation on the necessary mains voltage, type of current and fuse protection is to be obtained from the identification plate.
Connection cable
Error messages «U..»
2. Levelling
3. Electrical connections
Electrical connections must be carried out by trained electricians in accordance with the guidelines and standards for low volt-
age installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. A
mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and socket
devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching are
permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
If the appliance is supplied from a cord extension set or electrical portable outlet device the cord extension set or electrical
portable outlet device should be positioned so it is not subject to splashing or ingress of moisture.
230 V~ 50 Hz, 10 A
Colour code
L1 brown
blue
yellow/green
Disconnect the appliance from the mains and control the wiring.
3 × 1 mm²
N
L1
N

Installation instructions
Heat pump dryer
One-family household
J958.370-0
29.4.10 ITH
5
For Service and Spare Part Information please contact:
Manfred Schulz, Technical Manager
V-ZUG AUSTRALIA PTY LTD, c/o C.W. Stirling
6th floor 90 William Street, Melbourne, VIC 3000
[email protected]
Tel/ Fax [phone], Mob [phone]
Single connections
䡲Cannot be connected to a double drain trap.
䡲There must be a separate concealed drain trap for each appliance.
Washer-dryer combinations
䡲Can be connected to a double drain trap.
4. Connect condensate drain
When installing the drain hose, protect it against damage and bending! For that, use a hose clip 8.086.8039.
ALoosen screw A.
ARemove cover B.
APush the supplied drain hose C(2 m)
through the hole in the cover B.
APush on to the pump connection piece
and secure with a hose clip.
AReplace cover B.
APlace hose around retainer D.
Connection to sink drain trap Drain into fixed upright outflow pipe
The max. pumping height of the pump is 1.2 m
Washer-dryer tower Installation side by side
with combi drainage set
W5.4917
with drainage into fixed
upright outflow pipe
with combi drainage set
W5.4917
B
A
BC
B
C
D
min. 800
min. 350
max. 700
max. 700
max. 700

Installation instructions
Heat pump dryer
One-family household
J958.370-0
29.4.10 ITH
6
For Service and Spare Part Information please contact:
Manfred Schulz, Technical Manager
V-ZUG AUSTRALIA PTY LTD, c/o C.W. Stirling
6th floor 90 William Street, Melbourne, VIC 3000
[email protected]
Tel/ Fax [phone], Mob [phone]
When the appliance is connected to the power supply for the first time, it is possible to select a function test. The purpose of the function
test is to check the installation and it lasts about 3 minutes. For the function test the appliance must not to have been standing in the
normal operating position for approx. 2 hours as the heat pump is not started. The function test can therefore be selected immediately
after installation.
Start function test
AConnect appliance and wait for to show in the digital display.
AStart the function test with button .
The function test can be interrupted in 2 ways:
1. Open the appliance door.
– flashes in the digital display.
– Indicator lights for buttons and flash after closing the appliance door.
Or
2. Press the button.
– Indicator lights for buttons and flash.
Continue the function test:
APress the button.
– The remaining time shows in the digital display, e.g. .
Abort function test:
ABy pressing the button the function test is aborted and all displays go out.
End of function test:
– All displays go out on completion of the function test.
5. Using for the first time
The function test cannot be aborted by an interruption of the mains supply.
Once the function test has been run, it can no longer be selected and the appliance enters the normal selection mode.
The appliance is only ready to operate after the required waiting time of approx. 2 hours in the normal operating
position. Failure to observe this can result in damage to the appliance.