Cognex DataMan 280 Series User manual

DataMan®280 Series
Quick Reference Guide
2023 February 01
Revision: 23.1.0.5

Precautions
To reduce the risk of injury or equipment damage, observe the following precautions
when you install the Cognex product:
lConnectivity is possible through the following options:
l24 VDC (+/- 10%) output connection using a UL or NTRL listed
power supply
lPower over Ethernet (PoE) 13 W power supply
Any other voltage creates a risk of fire or shock and can damage the
components. Applicable national and local wiring standards and rules must
be followed.
lThis product is intended for industrial use in automated manufacturing or
similar applications.
lThe safety of any system incorporating this product is the responsibility of
the assembler of the system.
lDo not install Cognex products where they are exposed to environmental
hazards such as excessive heat, dust, moisture, humidity, impact, vibration,
corrosive substances, flammable substances, or static electricity.
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
lDo not expose the image sensor to laser light. Image sensors can be
damaged by direct, or reflected, laser light. If your application requires laser
light that might strike the image sensor, use a lens filter at the corresponding
laser wavelength. For suggestions, contact your local integrator or
application engineer.
2

lThisproduct does not contain user-serviceable parts. Do not make
electrical or mechanical modifications to product components.
Unauthorized modifications can void your warranty.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lInclude service loops with cable connections.
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThisdevice should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
3

Symbols
The following symbols indicate safety precautions and supplemental information:
WARNING:This symbol indicates a hazard that could cause death, serious personal injury or electrical
shock.
CAUTION:This symbol indicates a hazard that could result in property damage.
Note: This symbol indicates additional information about a subject.
Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.
4

Accessories
You can purchase the following components separately. For a list of options and
accessories, contact your local Cognex sales representative.
DataMan 280 Series Lenses
Accessory Product Number Illustration DM280 DM282
6.2 mm lens kit that includes:
l6.2 mm optics mount
l6.2 mm lens
lManual lens cap (assembled)
lScrews
DM280-LENS-62 ✓
16 mm lens kit with extended optics mount (requires
the use of an extended front cover and high-powered
red LED). The kit includes:
l16 mm optics mount
l16 mm lens
lManual lens cap (assembled)
lScrews
DM260-LENS-16 ✓
IR16 mm lens kit that includes:
l16 mm optics mount
l16 mm lens (IR)
lStandard Infrared Light for 16mm (Risk
Group Exempt acc. IEC62471)
lManual lens cap (assembled)
lScrews
DMA-KIT-IR-16 ✓
5

Accessory Product Number Illustration DM280 DM282
IR16 mm lens kit that includes:
l16 mm optics mount
l16 mm lens (IR)
lHigh Speed Liquid Lens Module (DMA-
HSLL-280)
lStandard Infrared Light for 16mm (Risk
Group Exempt acc. IEC62471)
lManual lens cap (assembled)
lScrews
280-KIT-2MP-IR16 ✓
High Speed Liquid Lens Module (HSLL) to be used
with 6.2 mm lens or 16 mm lens
DMA-HSLL-280 ✓ ✓
16 mm lens with ImageMax kit that includes:
l16 mm optics mount
l16 mm lens
lHigh Speed Liquid Lens Module (DMA-
HSLL-280)
lHigh Powered red LED illumination
(DM260-LED-RED-HP) (Risk Group
Exempt acc. IEC62471)
l2-LED half-polarized extended cover
(DM260-LENS-16CVR-P) (Risk Group
Exempt acc. IEC62471)
DM280-KIT-IMGMAX ✓
6

Accessory Product Number Illustration DM280 DM282
Blue bandpass filter DM150-BP470 ✓
Blue bandpass filter, 450nm 280-TORCH-BP450 ✓
Red bandpass filter DM150-BP635 ✓
Red bandpass filter, 635nm 280-TORCH-BP635 ✓
7

DataMan 280 Series Lens Covers
Accessory Product Number Illustration DM280 DM282
Standard front cover. Use with a 6.2 mm lens only. DM280-CVR-62 ✓
Standard front cover, half-polarized. Use with a 6.2 mm
lens only.
DM280-LENS-
62CVR-P
✓
Standard front cover, fully-polarized. Use with a 6.2
mm lens only.
DM260-LENS-
62CVR-F
✓
Extended front cover. Use with a 16 mm lens only. DM260-LENS-
16CVR
✓
Extended front cover, half-polarized. Use with a 16 mm
lens only. DM260-LENS-
16CVR-P
✓
Extended front cover, fully-polarized. Use with a 16 mm
lens only. DM260-LENS-
16CVR-F
✓
C-mount adapter, IP40 DM280-CMNT-00 ✓
8

Accessory Product Number Illustration DM280 DM282
Cross-polarized cover for High-Power Integrated Torch 280-HPIT-COVPOL ✓
Clear cover for High-Power Integrated Torch 280-HPIT-COVCLR ✓
Diffuse cover for High-Power Integrated Torch 280-HPIT-COVDIF ✓
Dome Diffuser cover for High-Power Integrated Torch 280-HPIT-DOME ✓
CAUTION:For 280-HPIT-COVPOL, 280-HPIT-COVCLR, and 280-HPIT-
COVDIF equipped with a laser aimer, the device has been tested to be under
the limits of a Class1 Laser device.
9

DataMan 280 Series Cables
Note: Cables are sold separately.
Accessory Product Number Illustration DM280 DM282
Ethernet Cable, X-coded M12-8
to RJ-45
CCB-84901-2001-xx (straight, xx specifies
length: 2m, 5m, 10m, 15m, 30m)
✓ ✓
Ethernet Cable, X-coded M12-8
to RJ-45
CCB-84901-2002-xx (right-angled, xx
specifies length: 2m, 5m, 10m)
✓ ✓
Ethernet Cable, Robotic X-
Coded M12-8 to RJ-45
CCB-84901-2RBT-xx (straight, xx specifies
length: 2m, 5m, 10m)
✓ ✓
X-Coded to A-Coded Ethernet
cable adapter, 0.5 m
CCB-M12X8MS-XCAC ✓ ✓
Power and I/O Breakout Cable,
M12-12 to Flying Lead
CCB-M12x12Fy-05 (y = straight/angled, xx
specifies length)
✓ ✓
Power and I/O Breakout Cable,
M12-12 to Flying Lead
CCBL-05-01 ✓ ✓
Power and I/O Breakout Cable,
M12-12 to Flying Lead
CCB-PWRIO- xx (straight, xx specifies
length: 5m, 10m, 15m)
✓ ✓
10