Colebrook Bosson Saunders AVALL Complete User manual

AVS-003-INST - F APRIL 2015
Installation Instructions
for AVALL Complete
AVS/003

AVS/002/DSK
AVALL COMPLETE SYSTEM
OPTIONAL ACCESSORIES TO CONFIGURE FOR DUAL SCREEN MOUNT
Single Screen Mount
AVAl l coMPlet e BASe & c oluMn
AVS/002/GA21
DuAl
Screen
Kit
AVS/003/A11
cAMerA Mount
AVS/002/CBM
AVAl l cAB le
MAnAgeMent Kit
PARTS INCLUDED: AVS/003/K01

BALANCE
SOME IMPORTANT PRECAUTIONS
LEVEL

INTERNAL
EQUIPMENT
S P A C E
SOME IMPORTANT PRECAUTIONS
WARNING
ELECTRICAL SAFETY
• Do not install screens/displays heavier than 60kg/132lb. Total weight of installed equipment must not exceed 120kg/264lb, symmetrically distributed.
• Use with products heavier than the maximum weights indicated may result in instability causing possible injury.
• Correct installation is essential to safe and reliable operation of the AVALL product and falls outside the scope of responsibility
of Colebrook Bosson Saunders. Please follow assembly instructions carefully.
• Do not use this product for any purpose other than that for which it was designed.
• Ensure that oor or wall surface is strong enough to support the weight of the fully-loaded AVALL and that the oor surface is at and level.
• Do not install AVALL outdoors or in environments where it will be directly exposed to moisture or highwinds.
• Follow the manufacturer’s guidance for mounting of screens, displays and other equipment.
• Please take care to avoid trapping ngers when installing or adjusting the product.
• Safe installation of electrical equipment is the responsibility of the installer.
• Colebrook Bosson Saunders recommends that only double-insulated electrical equipment and cables are installed in AVALL unit.
MAINTENANCE AND INSPECTION
• Ensure all screws and xings are fully tightened and occasionally re-tighten if necessary.
• Clean with a dampcloth. DO NOT use solvents.
IMPORTANT NOTE
Apply brakes at all times
(Unless AVALL is being moved)
IMPORTANT NOTE
Remember to support the back
panel when unlocking to prevent
it falling.

INSTALL THE SINGLE SCREEN MOUNT INSTALL THE D U A L SCREEN MOUNT
MOUNT RAILS TO SCREEN
1
1 B Fix the Mount rails
to the screen
Select xing screws
suitable for the screen
being mounted
1 A Plan the mounting position
Note orientation
of Mount rail
relative to screen
BottoM
toP
SCREEN WIDTH
CENTRE LINE
Plan the mounting position of the
mount to ensure that your chosen
screen ends up in the correct position
FOR AVAL L D U A L S C REEN KI T
REFER TO SEPARATE INSTALLATION
INSTRUCTIONS AVS/002/DSK
Ensure plastic caps
are fitted to tips of
the upper screws
Withdraw lower
screws to ensure
adequate clearance
for mounting
CABLE MANAGEMENT KIT
Extension brackets x 2
Mount rails x 2
AVS/002/GA21
Rail
Fixing kit
6 x M8 x 20
6 x M8 x 30
6 x M6 x 16
18 x Nylon Spacers
6 x M6 Washer
VC CAMERA MOUNT
USE SCREEN MOUNT KIT SUPPLIED WITH AVALL USE SCREEN MOUNT KIT
SUPPLIED WITH AVALL
P L U S
A V A L L D U A L S C R E E N K I T
SUPPLIED SEPERATELY
INCLUDED AV ACCESSORIES
PLEASE CONSULT THE RELEVANT INSTALLATION INSTRUCTIONS FOR EACH
PRODUCT, TO ENSURE THEIR POSITION AND INSTALLATION ARE CONSIDERED
BEFORE THE SCREENS ARE MOUNTED.

INSTALL MOUNT RAIL
3
x4
E
REMOVE/FIT BACK PANEL
2
clicK
IMPORTANT NOTE
Key must be inserted in
lock to close back panel
Remove 4 x M10 screws
and 4 x M10 nuts from
AVALL unit
3 A Use the screws and nuts
to install Mount Rail
3 B
x4
1 C OPTIONAL Fit extension brackets if required for larger screens

SECURE SCREEN
6
IMPORTANT NOTE
Tighten lower screws to
secure screen to mount
LEVELLING SCREEN
5
MOUNT SCREEN TO RAIL
4
2 people may be
required to mount
screens
ENSURE CAMERA MOUNT IS
INSTALLED AT THIS STAGE

[OPTIONAL] FINE ADJUSTMENT OF LOCK PANEL
9
USEFUL TIP
If necessary, adjust position
of lock plate to ensure
correct latching of lock
[OPTIONAL] CABLE STRAIN RELIEF
8
x1
CABLE MANAGEMENT
7
Pull cables clear
of the base
Clip cables into
management clip
underneath base
to secure
IMPORTANT NOTE
• Safe installation of electrical
equipment is the responsibility
of the installer.
• Colebrook Bosson Saunders
recommends that only double-
insulated electrical equipment and
cables are installed in AVALL unit.
7 A
7 B

REMOVAL/REFITTING LID
1 0
Slide lid backwards to release,
slide lid forwards to lock
1 0 A Lift lid 1 0 B
[OPTIONAL] REPOSITION RACK ASSEMBLY
1 1
Position A Position B
(For mounted fans)
Select holes according
to required position
F I T A V E Q U I P M E N T T O R A C K A S S E M B L Y
1 2
[oPtionAl]
Fit cooling fans
12A
ctrS
Fit AV equipment across rack
centers using supplied cage nuts
Fans to be installed according
to manufacturer guidelines
80mm fan
mounting
points
Ventilation airflow space
Feed cables in direction A
A
A
Fit AV equipment 12B
19” rack
mount points

SINGLE SCREEN MOUNT D U A L SCREEN MOUNT
INSTALLATION COMPLETE