Corning Pretium User manual

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 1 OF 10

Pretium™ Rack-mountable 1U

Housing Hardware

p/n 003-649, Issue 5

table of contents |

1. General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3. Product Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.1 Unpacking Stubbed Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.2 Removing the Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.3 Mounting the Housing into a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.4 Installing Cable Entry Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.5 Securing the Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.6 Strain-relieving the Cable Strength Member . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.7 Grounding Armored Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.8 Installing Preconnectorized Cable into Connector Panels . . . . . . . . . . . . . . . . . . . . . . . 6

3.9 Installing Closet Connector Housing Pigtail Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.10 Installing Preconnectorized Cable into Connector Modules (Plug & Play™) . . . . . . . . . 8

3.11 Installing a Buffer Tube Fan-out Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.12 Closing the Housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.13 Routing Patch Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4. Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

revision history |

Issue Date Reason for Change

5 01/2009 Added sections on installing pigtail modules and preconnectorized cable

into connector modules

4 05/2007 Added RoHS logo

3 11/2004 Update drawings with addition of removable bracket

2 03/2004 Corrected drawings in Figure 5

1 07/2003 Initial release

related literature |

LAN-538-EN Pretium Rack-mountable 1U Housing Hardware Product Specifications

LAN 539-EN Pretium Rack-mountable 1U Housing Hardware Ordering Guide

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 2 OF 10

admonishments |

The precautionary terms used by Corning Cable Systems in its standard recommended procedures

conform to the guidelines expressed in the American National Standards Institute document (ANSI

Z535) for hazard alert messages. Alerts are included in this instruction based on the following:

1. General

This document describes the installation of Pretium™-01U (Figure 1) Closet Connector Housing

Hardware. The unit fits into 19-inch utility racks and occupies one rack space. Factory stubbed units

are also available. Contact your customer service representative to order other mounting

configurations or to purchase accessories that are sold separately.

DANGER: indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: indicates a hazardous situation which, if not avoided, may result in

minor or moderate injury.

KPA-1191

Figure 1 — PCH-01U Housing

Dimensions

(H x W x D)

1.75 x 17 x 12 in.

(4.5 x 43 x 28.5 cm)

thgieWrebmuNtraP

)gk3.2(bl5U10-HCP

KPA-1192

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 3 OF 10

2. Components

The main components of the Pretium 1U hardware unit are illustrated in Figure 2. Cable and patch

cords can enter from either side of the housing.

3. Product Installation

3.1 Unpacking Stubbed Units

If you are installing a stubbed unit, follow the directions provided with the shipping container to

remove the stubbed unit from its packaging. Place the unit on a work surface to perform the

preliminary work before mounting the unit into a rack.

3.2 Removing the Cover

Removing the cover is optional but is recommended to ease installation

Step 1: Open front and rear doors.

Step 2: Locate the plunger fasteners at the front of the unit under the housing cover and pull out

to release the plungers (Figure 3).

Step 3: Lift stop latches and slide the cover toward the front until it is clear of the base. Set the

cover aside.

Cable Tie Locations

Mounting Bracket

Shown in Standard

5-inch Frontal

Projection Position

Radius Control Guides

Rear Tray

Stop Latch

Patch Cord Routing Guides

Front Tray

Stop Latch

Mounting

Bracket

Location for

3-inch

Removable Door

Lock Plug

Projection

From Rack

Removable Bracket

KPA-1193

Figure 2 — Components (Cover Removed for Clarity)

Plunger Fasteners

KPA-1194

Figure 3 — Remove Cover

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 4 OF 10

3.3 Mounting the Housing into a Rack

Attach the unit to the equipment rack using the four screws provided. Two screw are required per

side of the housing.

3.4 Installing Cable Entry Plate

Step 1: Determine location for cable entry into housing.

Step 2: Slide drawer back completely. The drawer must be in this position to prevent fiber

damage during drawer actuation.

Step 3: Install cable entry plate using the provided wing nut (Figure 4) at the location where the

cable will enter the housing.

Step 4: Install the strain-relief bracket to the side of the housing (Figure 4) at the location where

the cable will enter the housing.

3.5 Securing the Cable

NOTE: Fiber optic cable is sensitive to excessive pulling, bending, and crushing forces.

Consult the cable specification sheet for the cable you are installing. Do not

bend the cable more sharply than the minimum recommended bend radius.

Do not apply more pulling force to the cable than specified. Do not crush

the cable or allow it to kink. Doing so may cause damage than can alter the

transmission characteristics of the cable; the cable may have to be replaced.

The cable may be strain-relieved using the Universal Cable Clamp (UCC) or cable ties.

3.5.1 Using the UCC

Step 1: Attach the UCC clampshell to the strain-relief bracket as shown in Figure 5 to allow

installation of a second UCC if necessary.

Step 2: Follow installation instructions provided with the UCC kit to secure the cable. Allow room

on the bracket to strain-relieve the strength member, if necessary. Do not tighten yet to

allow for cable adjustment if necessary.

Step 3: Secure cable to cable entry plate using a cable tie. Do not tighten cable tie.

Cable Entry Plate

Strain-relief Bracket

KPA-1195

Figure 4 — Install Cable Entry Plate

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 5 OF 10

3.5.2 Using Cable Ties

If at least 10 m (33 ft) of outside plant cable is routed within an environmentally controlled building

where temperature fluctuation is minimal, securing the cable sheath is adequate strain-relief.

CAUTION: Wear safety glasses to protect your eyes from accidental injury when

handling chemicals and cutting fiber. Pieces of glass fiber are very sharp and can

damage the eye easily.

CAUTION: Wear safety gloves o protect hands from accidental injury when using

sharp instruments.

Step 1: Attach the cable to the strain-relief bracket with cable ties in two places as shown in

Figure 6.

Step 2: Allow room on the bracket to strain-relieve the cable strength member, if present.

Bracket Orientation for Top Cable Entry Bracket Orientation for Bottom Cable Entry

KPA-1196

Figure 5 — Strain-relieve Using UCC

Cable Ties

Yarn (If Present)

Strength Member

Flat Washer

U-shaped

Washer

KPA-1197

Figure 6 — Strain-relieve Strength Member

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 6 OF 10

3.6 Strain-relieving the Cable Strength Member

Step 1: Install the U-shaped washer and the flat washer on the strain-relief bracket using the

supplied Phillips-head machine screw (Figure 6).

Step 2: Place the yarn, if present, and the central member between the U-shaped washer and the

flat washer.

Step 3: Wrap yarn around the screw in a clockwise direction and under the U-shaped washer.

Step 4: Tighten the nut.

Step 5: Trim off the excess yarn and central member.

3.7 Grounding Armored Cable

• One grounding kit (p/n FDC-CABLE-GRND, purchased separately) is required to ground each

armored cable. Follow instructions provided with the grounding kit.

• Attach the other end of the ground wire to the equipment rack. The equipment rack must be

grounded to the primary building ground.

• Remove the paint from the frame at the grounding location to ensure metal-to-metal contact. It is

recommended to use an antioxidant on the bare metal to prevent corrosion.

• Or, attach the other end of the ground wire to a rack-mounted grounding bus bar, which is

grounded to the primary building ground.

3.8 Installing Preconnectorized Cable into Connector Panels

WARNING: Never look directly into the end of a fiber that may be carrying

laser light. Laser light is invisible and can damage your eyes. Viewing it directly

does not cause pain. The iris of the eye will not close involuntarily as when

viewing a bright light. Consequently, serious damage to the retina of the eye is

possible. Should accidental eye exposure to laser light be suspected, arrange for

an eye examination immediately.

WARNING: DO NOT use magnifiers in the presence of laser radiation. Diffused

laser light can cause eye damage if focused with optical instruments. Should

accidental eye exposure to laser light be suspected, arrange for an eye

examination immediately.

CAUTION: Isopropyl alcohol is flammable with a flashpoint at 54°F. It can cause

irritation to eyes on contact. In case of eye contact, flush eyes with water for at

least 15 minutes. Inhaling fumes may cause mild dizziness. In case of ingestion,

consult a physician.

Step 1: Remove the blank panels from the unit and replace with connector panels (purchased

separately).

Step 2: Install connectors into the adapters at the rear of the connector panels (Figure 7).

Step 3: Route cable slack around radius control guides.

IMPORTANT: Lift the tray stop latches and slide the drawer to the forward and back positions to

verify that the drawer slides in the grooves of the guides and that there is enough

fiber slack to prevent violating the minimum fiber bend radius of the cable.

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 7 OF 10

3.9 Installing Closet Connector Housing Pigtail Modules

Step 1: Remove the blank panels from the unit and replace with pigtail modules (purchased

separately).

Step 2: If you intend to splice inside the PCH-01U unit using the Splice Tray Kit (p/n PC1-SPLC-

04R), remove the radius control guides and install the splice tray kit per the instructions

provided with it. Route cable slack around kit and into the splice trays. Splice per the

instructions provided with the splice tray (Figure 8).

Step 3: If you intend to splice using an external splice housing, route slack around the radius

control guides and through the rear entry openings to the applicable splice housing above

or below the PCH-01U unit (Figure 9).

IMPORTANT: Lift the tray stop latches and slide the drawer to the forward and back positions to

verify that the drawer slides in the grooves of the guides and that there is enough

fiber slack to prevent violating the minimum fiber bend radius of the cable.

Cable Tie

KPA-1198

Figure 7 — Cable Slack Routing and Connector Installation

Cable Tie

KPA-2227

Figure 8 — Install Splice Tray Kit

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 8 OF 10

3.10 Installing Preconnectorized Cable into Connector Modules (Plug & Play™)

Step 1: Using a 6-32 hex nut driver, remove the radius control guides. (This is recommended

when cables enter from the right side of the housing.)

Step 2: Reinstall the nuts onto the radius guide studs to prevent fiber snags.

Step 3: Remove the blank panels from the unit and replace with connector modules (purchased

separately).

Step 4: Install MTP connectors into the MTP adapters at the rear of the connector modules

(Figure 10). Route fiber as shown and loosely secure with cable ties.

IMPORTANT: Lift the tray stop latches and slide the drawer to the forward and back positions to

verify that the drawer slides in the grooves of the guides and that there is enough

fiber slack to prevent violating the minimum fiber bend radius of the cable.

Cable Tie

KPA-2226

Figure 9 — Fiber Routing to External Splice Housing

Cable Tie

KPA-2245

Figure 10 — Install Plug & Play Modules

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 9 OF 10

3.11 Installing a Buffer Tube Fan-out Kit

Loose-tube fiber optic cable can be connectorized using Buffer Tube Fan-out (BTF) kits (purchased

separately).

Step 1: Terminate the fibers according to the instruction provided with the BTF kit.

Step 2: Slide drawer back completely and route buffer tube behind the flanges on the drawer and

secure with cable ties. Do not tighten cable ties. Route buffer tube around the radius

control guides.

Step 3: Secure the BTF body to the tray using a cable tie (Figure 11).

Step 4: Continue routing the fiber and install connectors into the adapters at the rear of the

connector panels.

3.12 Closing the Housing

Step 1: Lift up on stop latches and slide drawer toward the front of the housing to make sure

cable is not stressed. If necessary, readjust cable strain-relief to prevent stress on fibers.

Step 2: Slide drawer back to original position.

Step 3: If previously removed, slide the cover back in the retaining flanges on top of the housing.

Push the plunger fasteners to secure.

Step 4: Close the front and rear doors.

3.13 Routing Patch Cords

Install patch cords as specified on planning diagrams. Route patch cords through the routing clips on

either side at the front of the housing (Figure 12).

Provide enough patch cord slack to allow the connector panel tray to slide to the back and forward

positions without violating the minimum bend radius of the patch cord.

Record patch cord routing information on the identification (ID) label provided.

BTF Body

Flanges

KPA-1199

Figure 11 — Fan-out Fiber Routing

STANDARD RECOMMENDED PROCEDURE 003-649 | ISSUE 5 | JANUARY 2009 | PAGE 10 OF 10

Corning Cable Systems LLC √PO Box 489 √Hickory, NC 28603-0489 USA

1-800-743-2671 √FAX +1-828-325-5060 √International +1-828-901-5000 √http://www.corning.com/cablesystems

Corning Cable Systems reserves the right to improve, enhance, and modify the features and specifications of Corning Cable Systems’ products without prior notification.

Pretium and Plug & Play are trademarks of Corning Cable Systems Brands Inc. All other trademarks are the properties of their respective owners. Corning Cable Systems

is ISO 9001 certified.