Coleman Tent 919A162 User manual

STITCH LINE
BEACH SHADETM MODEL 9192A162
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or
sharp objects, to install your Beach Shade.
WARNING: Keep clear of overhead power lines.
• Do not set up your Beach Shade under trees.
• For best results in windy conditions, position end of Beach
Shade into the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the Beach Shade.
Fig. 1
Fig. 2
To Set Up Beach Shade
1. Unfold Beach Shade and spread out on a clean, level surface
with the door facing the desired direction. Unzip door.
(Fig. 1)
3. Assemble both Main (black) Poles and the Crossover (gray)
Pole by interlocking shock-corded poles.
4. Insert the Main (black) Poles through the pole sleeve running
side to side. (Fig. 3)
5. Insert the Crossover (gray) Pole through the pole sleeve
running side to side. (Fig. 3)
Fig. 3
6. Insert one end of the gray Crossover Pole into the grommet
on the web strap on either side of front door. (Fig. 4)
Fig. 6
Fig. 4
8. Go to the back of the
Beach Shade and
insert black Main Pole
tip into the grommet
on the web strap.
(Fig. 6)
To Set Up Beach Shelter (continued)
Fig. 5
(continued on other side)
Parts and Components
Description Part Number
Main Poles - Black (2) 9192-902
Crossover Pole - Gray (1) 9192-922
Main Poles (2)
Crossover Pole (1)
2. Stake down shade corners,
using the outside grommets on
the web straps. Keep the floor
taut. (Fig. 2)
Option: Use sand bags to weight
shelter down, see Fig. 15 & 16.
7. Go to opposite end of the gray pole and gradually apply
pressure to the pole, forming an arch, until you are able to
insert the pole tip into the grommet on the web strap. (Fig. 5)
9. From the front of the Beach Shade, gently pull the black Main
Pole down until you
can insert the end into
the grommet on
the web strap located
above the door open
ing. (Fig. 7)
10. Repeat for the
second black
Main Pole.
(Fig. 8)
Fig. 7
Fig. 8
Black Poles
Gray Pole

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2007 The Coleman Company, Inc.
Coleman®and are registered trademarks of The Coleman Company, Inc.
STITCH LINE
To Set Up Beach Shelter (continued)
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your Beach Shade. Condensation is caused
by water vapor from your breath, perspiration, or any wet clothing inside
the Beach Shade. It is NOT LEAKAGE through the shelter fabric. It can be
minimized by removing wet clothing from your shelter and by providing
good ventilation through the Beach Shade.
• Never store Beach Shade, even for a short period of time, without drying
it thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your Beach Shade. Use a separate storage bag.
• Stakes should be removed by pulling on the stake itself. Never pull on
the Beach Shade to remove stakes.
• BEACH SHADE POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
• Do not leave your Beach Shade set-up for weeks at a time. Be aware that
exposure to ultraviolet rays from the sun can seriously damage material
and/or cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this shelter fabric.
This shelter meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
To Store
1. All poles and metal stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure Beach Shade is clean and dry before placing in
carry case.
3. Neatly fold Beach Shade to width of pole storage bag. Place
storage bag on folded Beach Shade, roll tightly, and place in
carry case.
4. Store in a clean, dry area.
03/07
To Secure Beach Shade in Sandy Terrain
1. Fill the (6) sand bags with sand or small rocks. (Fig. 15)
2. Insert the toggle of the filled sandbag through the grommet
on the stake loop where the stake would have been. (Fig. 16)
3. Bury the sand bag to secure the Beach Shade.
4. Tie the end of the guy line to the sand bag, extend and bury.
Repeat for second guy line.
12. Extend guy lines out until
taut then secure with stakes.
(Fig. 10 & 11)
Fig. 10
Fig. 11
Fig. 15
11. Attach guy lines to the front of the Beach Shade, above the
large door, by
inserting the guy
line through the
webbing between
the grommet and
the shade material.
(Fig. 9)
Storage for Small Items
1. Hang the storage bag
on the fabric loops to
keep small items off
the floor. (Fig. 12)
2. Use cord located
above front door of
the Beach Shade as
a dry line. Fig. 12
Rear Vent Flap
The rear flap of the Beach Shade may be raised and lowered to
allow for better ventilation, improve lighting, or privacy.
1. Unzip inside flap to expose mess screen for ventilation.
2. Roll flap up and
secure by inserting
both dowels through
loops. (Fig. 13)
Fig. 13
Loops &
Dowels
3. Undo outer zipper on rear vent flap and roll up for ventilation
or additional access to Beach Shade.
4. Roll flap up and
secure by inserting
both dowels through
loops. (Fig. 14)
Fig. 14
Loops &
Dowels
Fig. 9
Fig. 16
Front Door Flap
The front door of the Beach Shade may be closed for more
privacy with the zippers .