Coleman SaluSpa Havana AirJet 90443E User manual

DO NOT RETURN THIS ITEM TO THE STORE OR
WEBSITE WHERE IT WAS PURCHASED. PLEASE
VISIT WWW.BESTWAYCORP.COM/SUPPORT
FOR QUESTIONS, OR FOR DEFECTIVE OR
WARRANTY CLAIMS.
Owner’s Manual
Para la instrucción en español,
visite bestwaycorp.com/support
110-120V~60Hz, 12A at 68°F (20ºC)
#90443E
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
303021236526

WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 8 AWG (8.37 mm2)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER –
Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal
surface is permanently connected by a minimum 8 AWG (8.37 mm2) solid copper
conductor to the wire connector on the terminal box that is provided for this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f ) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.
CAUTION: The spa should not be setup or left out in temperatures lower than 40°F
(4°C).
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION:
Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway®at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
CONTENTS
1. Warning .................................. P12
P7
P10
P2
2. Installation .............................
Selected Location
GFCI Test
Assembly
3. Pump Operation .....................
Control Panel
Alarms
4. Maintenance ........................
Filter Cartridge Maintenance
Water Maintenance
Air-Valve Adjustment
Draining the Spa
Cleaning the Spa
Deflation
Spa Repair
P14
5. Troubleshooting ................
2
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS

WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 8 AWG (8.37 mm2)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER –
Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal
surface is permanently connected by a minimum 8 AWG (8.37 mm2) solid copper
conductor to the wire connector on the terminal box that is provided for this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
3
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f ) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.
CAUTION: The spa should not be setup or left out in temperatures lower than 40°F
(4°C).
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION:
Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway®at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS

WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 8 AWG (8.37 mm2)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER –
Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal
surface is permanently connected by a minimum 8 AWG (8.37 mm2) solid copper
conductor to the wire connector on the terminal box that is provided for this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f ) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.
CAUTION: The spa should not be setup or left out in temperatures lower than 40°F
(4°C).
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION:
Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway®at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
ASSEMBLY: THE PROVIDED WARNING LABEL
WARNING
REDUCE THE RISK OF ELECTROCUTION
1. NEVER PLACE AN ELECTRIC APPLIANCE WITHIN 5 FEET OF SPA.
REDUCE THE RISK OF CHILD DROWNING
1. SUPERVISE CHILDREN AT ALL TIMES.
2. ATTACH SPA COVER AFTER EACH USE.
REDUCE THE RISK OF OVERHEATING
1. CHECK WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN POOR
HEALTH, OR UNDER MEDICAL CARE.
2. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY, OR SLEEPY. SPA HEAT
CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS.
3. SPA HEAT IN CONJUNCTION WITH ALCOHOL, DRUGS, OR MEDICATION
CAN CAUSE UNCONSCIOUSNESS.
WHEN PREGNANT, SOAKING IN HOT WATER FOR LONG PERIODS CAN
HARM YOUR FETUS. MEASURE WATER TEMPERATURE BEFORE ENTERING.
1. DO NOT ENTER SPA IF WATER IS HOTTER THAN 100
O
F (38
O
C)
2. DO NOT STAY IN SPA FOR LONGER THAN 10 MINUTES.
4
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS

5
Be sure to cover the spa with the spa cover whenever the heating function is
activated. Leaving the spa uncovered will inrease the heating duration required.
Please do not use the spa when ambient temperature is lower than 39°F.
IMPORTANT !
To reach 104°F (40°C), the heating duration required is base on the starting water temperature and
ambient temperature, the data below is purely for reference. To display the current water
temperature, run the filter system for at least a minute.
NOTE: The warning label must be posted near your spa in a readable position
during using your spa.
1. Take out the warning label from the accessory kit.
2. Carefully peel the warning label.
3. Affix the warning label.
To order the warning label, please contact your local Bestway After Sales Service.
Ambient Temperature
50°F
59°F
68°F
77°F
86°F
Water Temperature
50°F
59°F
68°F
77°F
86°F
Set Temperature
104°F
104°F
104°F
104°F
104°F
Heating Duration
32 h
26 h
20 h
14 h
9 h
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
Power Rate Massage Tube Power Heat Element Power Water Pump Power
11.3A at 20ºC 0.7A
110-120V AC,
12A at 20ºC 6.5A

Part N.
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
Part Code
P04884
P05088
P04885
54123GASS17
P6931ASS16
P04674
P03821
P6934ASS16
P6575ASS16
F4C009B-02ASS17
P00217
F6414ASS16
90352E
P61726ASS18
P61727ASS18
P00260
P6609ASS16
P05038
Description
Pool liner
Spa Heater
Top Reinforce Cover
Inflatable Cover
Inflation Hose
Filter Set
Chemical Dispenser
Water Hose Set
Stoppers
Screw Valve
Cover Adapter A
Buckle
Filter Cartridge (VI)
Deflation T-joint
Deflation Valve Adapter
Spa Debris Screen
Deflation Seal Ring
Remote Control
QTY
1
1
1
1
1
2
1
1
3
1
1
6
2
1
1
1
1
1
012
017 018
SPECIFICATIONS
Water Capacity
(80%):
Inflated Size:
Filled Weight: Temperature
Capacities:
Working Pressure:
Capacity:
177 gal. (669 L)
71in. x 26in.
(1.80m x 66cm)
1,534 lbs. (696 kg) 104ºF (40ºC)
0.055Bar (0.8PSI)
2-4 Adults
Heat Element:
Pump:
Actual Water Flow:
Massaging
Turbo Blower:
11.3A at
68ºF (20ºC)
0.7A Circulation
Filter Pump
Power Rate: 110-120V AC,
12A at 68ºF (20ºC)
Approximately
2-3ºF/h (1-1.5ºC/h)
350 gal./h (1,325 L/h)
Increased Heat
Rate:
6.5A
NOTE: The above heating rate is based on a lab test conducted
with an ambient temperature of 77ºF (25ºC) and above.
6
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书

7
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
GFCI Test
IMPORTANT: RISK OF ELECTRIC SHOCK. THE GFCI
MUST BE TESTED BEFORE TURNING ON THE PUMP
EACH TIME.
INSTALLATION
Selected Location
IMPORTANT: Because of the combined weight of the
SaluSpa, water, and users, it is extremely important that the
base where the SaluSpa is installed is smooth, flat, level and
capable of uniformly supporting the weight for the entire time
the SaluSpa is installed (not on the carpet or other similar
material). If the SaluSpa is placed on a surface, which does
not meet these requirements, any damage caused by
improper support is not covered under the manufacturer’s
warranty. It is the responsibility of the SaluSpa owner to
assure the integrity of the site at all times.
1. Indoor Installation:
Be aware of special requirements if you install the spa
indoors.
• Humidity is a natural side effect with SaluSpa installation.
Determine the effects of airborne moisture on exposed
wood, paper, etc. in the proposed location. To minimize
these effects it is best to provide plenty of ventilation to the
selected area. An architect can help determine if more
ventilation is needed.
2. Outdoor Installation:
• During filling, draining or when in use, water may spill out of
the spa. Therefore the SaluSpa should be installed near a
floor drain.
• Do not leave the spa's surface exposed to direct sunlight for
long periods of time.

1. Plug the GFCI into a power outlet, the indicator turns red.
2. Press the test button, the indicator turns off.
3. Press the reset button, the indicator turns red and the spa is
ready for use.
WARNING: The GFCI plug must be tested before each use to
avoid risk of electric shock.
WARNING: Before inserting plug into a power outlet, make
sure the current rate of the power outlet is suitable for the
pump.
WARNING: Do not use the pump if this test fails and contact
our Aftersales Service.
WARNING: Using an extension lead or multi plug adaptor with
the spa heater can cause the plug to overheat, causing
damage to the equipment and surrounding items. The spa is a
class I electrical appliance and must be connected directly to a
grounded socket. It is recommended to only use a socket which
is resistant to humidity and capable of high power loading.
Regularly check the plug and socket for signs of damage
before using the spa – do not use the spa if the plug or socket
is damaged. If you are unsure about the quality of the electrical
supply, please consult a qualified electrician before use.
-
l
o
i
n
5
NOTE: When inflating, you will notice that air will be expelled from the area
where the air hose connects to the pump, this is normal for technique
requirements.
NOTE: Do not use an air compressor to inflate the pool.
NOTE: Do not drag the pool on rough ground
as this may cause damage to the pool liner.
NOTE: Inflation time for reference only.
It is recommended to find for a professional electrician to
connect the SPA pump to the grounding end of the house with
a solid copper conductor of at least 8AWG (8.37mm2).
8
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书

9
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
6. 7. 8.
10.
To stop inflation.
3 seconds to unlock.
1. 3.
Inflate for 5 min.
1
4. 5.
Inflate for 2 min.
2
1
2.
P6609ASS16
s
e
c
.
s
C
o
n
t
r
o
l
s
e
c
.
9.
MAX.
MIN.
Assembly

Hyperthermia occurs when the internal temperature of the body reaches a level
several degrees above the normal body temperature of 37°C (98.6°F). The
symptoms of hyperthermia include an increase in the internal temperature of
the body, dizziness, lethargy, drowsiness, and fainting. The effects of
hyperthermia include failure to perceive heat; failure to recognize the need to
exit spa or hot tub; unawareness of impending hazard; fetal damage in
pregnant women; physical inability to exit the spa or hot tub; and
unconsciousness resulting in the danger of drowning.
WARNING: THE USE OF ALCOHOL OR DRUGS CAN GREATLY INCREASE
THE RISK OF FATAL HYPERTHERMIA IN HOT TUBS AND SPAS.
The pump has a 5-minute auto-lock. The LED light will dim out when the pump is locked (no function is activated). To lock or unlock the pump,
place a finger over the lock/unlock button for 3 seconds.
Lock/Unlock Button
Power-Saving Timer Button
This is a newly added function, designed to help avoid wasting power by setting the time and duration of the heating cycle for the spa.
This way, you can enjoy your spa at the time you desire, without needing to leave the heater on at all times.
Pressing the Temperature Increase or Decrease buttons will cause the LED to flash. When it is flashing you can adjust to the desired temperature
setting. If you hold these buttons down the values will rapidly increase or decrease. The new and desired temperature setting will remain on the LED
display for 3 seconds to confirm the new value.
Once powered-up the LED displays the current water temperature automatically.
After 72 hours of filtration (without using the power saving timer function), the pump will hibernate and flash “End” with the current water
temperature. When the pump is hibernating both the heating and water filter functions are disabled. To re-activate the pump press
lock/unlock button for 3 seconds.
Use this button to activate the heating system. When the light above the heat button is red, the heating system is activated. When the
light is green, the water is at the set temperature and the heating system is at rest.
The temperature can be displayed in either Fahrenheit or Celsius.
NOTE: If the heating system is activated the filtration system will automatically start.
NOTE: After turning off the heating system the filtration system will continue to operate.
NOTE: The default temperature is 35°C (95°F).
NOTE: Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
Temperature Adjustment Buttons
Celsius/Fahrenheit Toggle
Heat Button
This button turns the filter pump on and off. The light above the Water Filter Button displays red when activated.
Water Filter Button
Power-Saving Timer LED
LED Display
NOTE: The water heat rate may change in the conditions below:
• When the outdoor temperature is below 15°C (59°F).
• If the cover is not in position when the heating function is activated.
NOTE: To display the current water temperature, run the filter system for at least a minute. The water temperature as tested by an external
thermometer may vary from the temperature as displayed on the spa panel by as much as approximately 2°C.
Press this button for 2 seconds to active the control panel bottons and the light turns to green. Press this button for 2 seconds to turn off all currently
activated functions.
On/Off Button
This LED flashing means you are setting the heating duration. The light will be on when the heating function starts to work.
This LED flashing means you are setting the number of hours FROM NOW when
the heater will activate. When the light is on, the Power-Saving Timer function is set.
STEP 1: Set the heating duration
1. Press the button unit the LED starts to flash.
2. Press the or button to adjust the heating duration (From 1-48 hours).
3. Press the button again to confirm the heating duration.
STEP 2: Set the number of hours FROM NOW when the heater will activate
1. After setting the heating duration, the LED starts to flash.
2. Press the or button to adjust the hours until time of activation (From 0-99 hours).
3. Press button again or simply touch nothing for 10 seconds to confirmthe setting. The LED will light steadily, and the countdown to heater
activation will begin.
To modify the timer settings: Press the button and use the or button to adjust.
Cancel the setting: Press the button for 2 seconds.
NOTE: After setting, the screen flashes the current temperature and time alternately.
NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 48 hours; Reservation time adjustment (the number of hours FROM
NOW when the heater will begin to function) may be set from 0 to 99 hours. If the timer is set at 0 hour, the heating system will activate immediately.
Note that the timer is one time per use - the user sets the duration of the heating cycle, and how many hours from now the heating cycle begins. The
timer does NOT repeat until reset.
Use this button to activate the massage system, which has a 30-minute auto-shutoff feature. The light above the Massage System Button
displays red when activated.
IMPORTANT: Do not run the Massage system when the cover is attached. Air can accumulate inside the spa and cause
irreparable damage and bodily harm.
NOTE: Heat and massage system work together to create a warm massage experience.
Massage System Button
10
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
Control Panel Operation Instructions:

LCD Display
Temperature Adjustment Buttons
Massage System Button
On/Off Button
Heat Button
Water Filter Button
IMPORTANT: If spa is turned off, the remote control will not
work. Insert the spa plug, reset the GFCI, and then use the
remote control.
When the remote control is activated, the LCD display screen
will stay on for about 15 seconds. After that, it will automatically
shut down. To use the remote control again, press any button.
NOTE: Press any button on remote control to synch with spa
panel when operating the spa panel.
WARNING !
Do not put the remote control in the water.
If the remote control falls into water, take it
out of the water immediately.
Damage to the remote control caused by immersion in water
is not covered under your warranty.
Pairing Instructions:
The remote control that comes with your spa is already paired with the spa. If the spa pump or remote control are replaced, you have to pair them again
according to the following instructions:
1. Connect the pump to a power source and press the reset button on the GFCI.
2. Press the button on the control panel for 3 seconds. Then the indicator will start to flash, and the pump has entered the pairing mode.
3. Press the button on the remote control for 3 seconds, and the LCD display on the remote control will show "PIR".
After several seconds, it will display "PAS". The remote control is ready to use.
NOTE: If the pairing operation did not finish within 20 seconds, it must be restarted.
NOTE: The distance between the remote control and the pump must be less than 10 m (33 ft.).
Battery Warnings:
• Do not mix old and new batteries.
• Do not mix the different types of batteries. Do not mix alkaline, standard (Carbon - Zinc), or rechargeable (Nickel - Cadmium) batteries.
• Ensure batteries are installed correctly with regard to polarity (+ and -).
• Do not short-circuit the battery.
• Never attempt to recharge primary batteries as this may cause leakage, fire, or explosion.
• Rechargeable batteries are to be removed from this product before being charged.
• Never attempt to disassemble or open batteries as this can lead to electrolyte burns.
• Remove batteries from equipment which is not to be used for an extended period of time.
• Exhausted batteries are to be removed from this product.
• Do not dispose of product and its batteries in fire. Check your local regulations for proper disposal instructions.
• Batteries shall not be exposed to excessive heat such as sunshine, fire or the similar.
• Keep batteries out of the reach of children.
• Only use 2x CR2032 batteries.
To replace the battery:
11
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书

MAINTENANCE
Your spa will require additional air to be added from time
to time. Changes in temperature from day to night will
change the pressure in the spa and may cause a certain
amount of deflation. Please follow the Assembly
instructions and drain the spa before inflating to the
accurate pressure needed.
CAUTION: YOU MUST ENSURE THE PUMP IS
UNPLUGGED BEFORE BEGINNING SPA MAINTENANCE
TO AVOID RISK OF INJURY OR DEATH.
P04674
Filter Set
90352E
Filter Cartridge
Alarms
Solutions
Causes Reasons
The water flow sensors
work without pressing the
filter or heat button.
1. The water flow sensor flags didn’t fall back
into the correct position.
2. The water flow sensors are broken.
1. Unplug the plug gently, strike the side of the pump (but not violently), and
plug it back in.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
After starting or during the
functions of filtering or/and
heating, the water flow
sensors do not detect
water flow.
1. You forgot to remove the 3 stopper caps from
inside the pool.
2. Filter cartridges are dirty.
3. Activate the filter or heat system and put your
hand in front of the outlet pipe inside the pool to
check if you can feel water flowing out.
a. If no water flows out the water pump is broken.
b. Water flows out but the alarm appears,
the water flow sensors are broken.
4. Filter blockage
5. Bent pipes or poor water flow through the
plasticpipes of the liner
6. Debris screens are blocked: debris screens can
become blocked by hard water due to calcium
build-up.
7. Perished washers
The washers within the spa couplings may have
become perished or worn.
1. Remove the 2 stopper caps before heating, refer to Assembly section in the
User’s Manual.
2. Remove the filter set from inside the pool and push the filter or heat button. If
no alarm appears, clean or change the filter cartridges install the filter set
inside the pool.
3. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
4. Clean the filter and check for damage. Replace or re-install as necessary.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
5. Please check through the spa connection to see if the pipes are bending.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
6. Empty the spa and place a garden hose inside the pipes to wash the debris.
To be sure all debris is removed, perform the operation from the outside and
inside of the spa.
Use a toothbrush to remove any stubborn debris.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
7. Check the washers inside the coupling for damage. Unscrew the couplings
and remove the washer for further inspection.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The thermal cut-out cut
off.
1. The ambient temperature is over 50°C (122°F) or
the pump is directly under the sunshine.
2. The thermal cut-out is broken.
1. Unplug the pump, and put the pump in a dry, cool place. Only re-start the
pump when the water temperature reaches 34°C (93.2°F) or lower.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer
connections have issues.
1. The pump’s thermometer connectors don’t
work properly.
2. The pump’s thermometer is broken.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer
reads the water
temperature below
4°C (40°F).
1. The water temperature is lower than
4°C (40°F)
2. If the water temperature is higher than
7°C (44.6°F), the pump’s thermometer is broken.
1. The spa is not designed to operate with water temperatures lower than
4ºC (40°F). Unplug the pump and only re-start the pump when the water
temperature reaches 6°C (43°F).
2.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer
reads the water
temperature over
48°C (119°F).
1. The water temperature is over 48°C (119°F)
2. If the water temperature is lower than
45°C (113°F), the pump’s thermometer is
broken.
1. The spa is not designed to operate with water temperatures greater than
40°C (104°F). Unplug the pump and only re-start the pump when the water temperature
reaches 38°C (100°F) or lower.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
Filter Cartridge Maintenance
NOTE: To ensure your spa water stays clean,
check and clean your filter cartridges
every day follow the steps below.
12
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书

Using chemical liquid (not included):
Using chemical tablets (not included):
NOTE: Damage resulting from chemical imbalance is not covered by the warranty. Pool chemicals are potentially toxic and should be
handled with care. There are serious health risks from chemical vapors and the incorrect labeling and storage of chemical containers.
Please consult your local pool supply retailer for more information about chemical maintenance. Pay close attention to the chemical
manufacturer's instructions. Spa damage resulting from misuse of chemicals and mismanagement of spa water is not covered by the
warranty.
NOTE: Remove the chemical dispenser from spa when the spa is in use.
IMPORTANT: After performing chemical maintenance and
before using the spa, use a test kit (not included) to test the
water chemistry. We recommend maintaining your water as table
below.
pH
7.4-7.6
Total Alkalinity
80-120ppm
Free Chlorine
2-4ppm
C
o
n
-
l
o
i
n
5
-
l
o
i
n
5
s
e
c
.
STORAGE
Draining the Spa
13
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
NOTE: We recommend changing your filter cartridges every week or, if the filter cartridges remain soiled and discolored, they should be replaced.
Water Maintenance
Keeping your spa water clean and chemically balanced is necessary. Simply cleaning the filter cartridge is not enough for proper maintenance, we
recommend you use pool chemicals to maintain water chemistry and chlorine or bromine tablets (do not use granules) with the chemical dispenser.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic products, lotions, and other residues on the skin can quickly degrade
water quality. To use the chemical dispenser, please follow the below instruction.
NOTE: When treating your pool, the chemical floater or ChemConnect™ must be used. Never add chemicals directly into the water. If undiluted
chemicals come into contact with the PVC material, it can cause serious damage to the liner as well as quickly fade the internal printing. The chemical
floater and the ChemConnect™are designed to be used strictly with tablets. The maximum amount that the ChemConnect™ and chemical floaters can
hold is 4 tablets. We strongly recommend not using any granulated or liquid chlorine when cleaning your pool. However, in the case of usage, please note
it must be diluted completely into water before adding to your pool. When adding the chemicals to the water, place small doses into the center of the pool,
away from the walls. Be sure that the filtration system is turned on and nobody is using the pool when adding chemicals.
2. 3. 4.
6.
1.
7.
5.
8. NOTE: Dry the spa pool.
NOTE: Lift up the spa when there is
only a little water left. Damages to
the handles are not covered under
the warranty.
P00217

14
DEFLATION
Detergent residues and dissolved solids from bathing suits and chemicals may build
up on the spa walls. Use soap and water to clean the walls and rinse thoroughly.
NOTE: DO NOT use hard brushes or abrasive cleaners.
Cleaning the spa
2.
1.
P61726ASS18
P61726ASS18
P61727ASS18
Safety valve
2
P61727ASS18
-
l
o
i
n
5
s
e
c
.
Screw valve
Make sure the spa and pump are completely dry. This is essential to extend the life of the spa. We recommend using the pump to blow dry the spa, pump
and pipes. Remove the filter sets and discard the used filter cartridges. Re-attach the two stopper caps onto the spa’s inlet and outlet valves. It is
recommended you store the spa in its original package in a warm dry place.
NOTE: Plastic becomes brittle and susceptible to breaking when exposed to subzero temperatures. Freezing can severely damage the spa. Improper
winterization of your spa can void your warranty.
TROUBLESHOOTING Bestway strives to provide the most trouble-free spas on the market.
If you experience any problems whatsoever, do not hesitate to contact Bestway or your authorized dealer. Here are some helpful tips to help you to
diagnose and rectify some common sources of trouble.
REPAIR
For PVC part.
If the spa is torn or punctured, use the provided underwater adhesive repair patch.
1. Clean area to be repaired.
2. Carefully peel patch.
3. Press patch over area to be repaired.
4. Wait 30 seconds before inflation.
For Tritech PVC material.
If the spa is torn or punctured, use the provided PVC repair patch and glue (not included) following these steps:
1. Clean and dry area to be repaired.
2. Cut the provided PVC patch to appropriate size.
3. Use glue (not included) to coat the one side of the newly cut patch. Make sure the glue is evenly distributed.
4. Wait for 30 seconds and then place the cut patch with glue over the damaged area.
5. Smooth out any bubbles of air that may be trapped underneath, and press firmly for two minutes.
6. The product is once again ready for use. Repeat this process should further leaks occur.
7. Wait 30 minutes before inflation.
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书

15
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书
Problems
Pump does not operate
Pump does not
heat properly
Massage System
does not work
Pump adapters are not
level with the spa
adapters
Spa pool leakage
Water is not clean
Probable Causes
- Spa is torn or punctured
- Air valve is loose
Solutions
- Check power source
- For assistance, please visit the support section on our website,
www.bestwaycorp.com
- Elevate the pump with wood or another type of insulated material to
bring the pump's adapters level with the spa's adapters
- Power failure
- GFCI broken
- Air Pump is overheating
- The massage system stops
automatically
- Air pump is broken
One characteristic of PVC
is that it changes shape,
which is normal
- Insufficient filtering time
- Dirty Filter Cartridge
- Improper water maintenance
- Unplug the pump and wait two hours until the pump has cooled.
Insert the plug and press the massage system button
- Press the massage system button to reactivate
- For assistance, please visit the support section on our website,
www.bestwaycorp.com
- Increase filtration time
- Clean/replace the Filter Cartridge (refer to Filter Cartridge Cleaning and
Replacement section)
- Refer to the chemical manufacturer’s instructions
Control panel not
working
The control panel has an auto-lock,
which is activated after 5 minutes of
inactivity. The LED display has one
icon: If the lock icon is highlighted,
the control panel is locked.
- Control panel is not activated.
- Seals are missing inside the pump
adapters
- Seals are not in the correct position
- Seals are damaged
- Adapters are not tightened correctly
- The pump did not pair with the remote
control
- The pump is not plugged in
- The remote control is out of range
- The remote control battery is dead or
not inserted correctly
- The remote control is damage
What kind of chemicals
should be used for water
maintenance?
GFCI test failed There is a defect in your spa For assistance, please visit the support section on our website,
www.bestwaycorp.com.
Please consult your local chemical supplier for information about chemical maintenance.
Pay close attention to the chemical manufacturer’s instructions
Water leaks from the
adapters between the
pump and spa
Remote control does
not work
- Insert the stopper caps on the spa ports to prevent the water from
escaping and disconnect the pump. Check if the seals are in place.
- If the seals are not in the correct position, open the gears, and place
the seals in correct position.
- If the seals are damaged, they must be replaced. for assistance, please
visit the support section on our website, www.bestwaycorp.com.
- If the seals are in correct position, the adapters are not tightened
correctly. Connect the pump to the spa, hand-tighten the adapters, and
remove the stopper caps from the spa ports. If there is leakage, tighten
the adapter until there is no leakage.
- Pair the remote control with the pump
- Insert the plug and press the "RESET" button
- Bring the remote control within 10 m(33ft.) of the pump
- Take out the battery and reinstall.If the remote control is still not
shown, replace with new batteries.
- For assistance, please visit the support section on our website,
www.bestwaycorp.com
- Use provided repair patch
- Using soapy water, cover the air-valve to check if air is leaking, if so,
use the provided wrench to fasten the air-valve following these steps:
1. Deflate the SPA.
2. With one hand, hold the backside of the air valve from the inner side
of the spa wall and turn the wrench clockwise.
- Temperature set too low
- Dirty Filter Cartridge
- The thermal cut-out cut off
- Spa is not covered
- Heating element failed or
fuse cutout
- Set to a higher temperature refer tosection pump operation
- Clean/replace the filter cartridge referto section filter cartridge
cleaning and replacement
- Unplug the pump, and put the plug in a dry, cool place. Only restart the
pump when the water temperature reaches 35°C (95°F) or lower
- Attach the cover
- For assistance, please visit the support section on our website,
www.bestwaycorp.com
- To unlock the control panel, press the button for 3 seconds.
If the control panel will not unlock, restart the pump – unplug and
plug in the pump
- Press the on/off button for 2 seconds. If the problem persists,
for assistance, please visit the support section on our website,
www.bestwaycorp.com

16
Date:
IMPORTANT: ONLY THE DAMAGED PART WILL BE REPLACED, NOT THE COMPLETE SET.
Bestway
®
reserves the right to request photographic evidence of defective parts, or to require sending the item for additional testing.
In order to better assist you, we request all information you provide to be complete.
FOR FAQ, MANUALS, VIDEOS OR SPARE PARTS, PLEASE VISIT OUR WEBSITE: www.bestwaycorp.com.
Heating System not workingSpa leakage
Massage System not working
Missing Part - Please use the code for the missing part. This
can be found in the owner’s manual.
Control panel shows a failure which cannot be solved
Pump leakage Adapter leakage
Other (Please describe)
All drawings for illustration purpose only. Not to scale.
Problem description
Spa Pump Item Code:
Water Filtration System not working
Batch Number
BWSHE.....X
YYYY-MM-DD
BWSHEXXXXXX
YYYY-MM-DD
Close
Open
Batch Number Item Code
MODEL NO. #XXXXX
BW
S
Y
H
Y
E
Y
X
Y
X
-
X
M
X
M
X
-
X
DD
Batch Number
YYYY
BWSHEXXXXXX
-MM-DD
Spa Pool Batch Number:
Spa Pump Batch Number:
REQUIRED INFORMATION - PLEASE WRITE THE SHIPPING ADDRESS
Name: Address:
Zip Code: Retailer:
State / Country:
City:
Mobile: Telephone:
Fax: E-mail:
•
L
I
M
I
T
E
D
•
•
W
A
R
R
A
N
T
Y
•
The product you have purchased comes accompanied by a limited warranty. Bestway
®
stands behind our quality guarantee and
assures, through a replacement warranty, your product will be free from manufacturer’s defects. The limited warranty is valid as
follows:
360 days for the heater pump from the original date of purchase
180 days for the pool liner from the original data of purchase
30 days for hoses, fitting and accessory included in the package from the original date of purchase
To enact a warranty claim, please contact your local Bestway
®
After Sales Center at 1-855-838-3888 before sending any
documents. They will provide full instructions of what is needed for your claim. Bestway
®
is not responsible for economic loss due
to water or chemical costs.
Bestway
®
will not replace any products deemed to have been neglected or used outside of the owner’s manual guidelines.
Bestway’s warranty covers manufacturing defects discovered while unpacking the product or during use as recommended within
the user manual. This warranty applies only to products which have not been modified by any 3
rd
parties. The product must be
stored and handled in accordance with the technical recommendations.
The warranty does not cover damages caused by misuse, abuse, neglect, including, but not limited to collision, fire, use of
incorrect voltage, excessive heat exposure, improper installation, improper wiring or testing or improper storage. Replacements
and repairs don’t extend the duration of the warranty. The Limited Warranty is valid for the period indicated above. The warranty
start date is the date of sale shown on the original receipt/purchase invoice.
Please choose your Spa
Date of purchase:
TO:
Bestway
®Service Department
Customer Code Number:
Website: www.bestwaycorp.com Toll-Free: 1-855-838-3888 Please provide your address details in full.
Note: Incomplete address details will result in delayed shipments.
Bestway
®reserves the right to charge for redelivery of undelivered packages where the recipient is at fault.
303021236526_14.0x21.0cm_90443E_20N-OEM-381_美国规SPA主体说明书