Collcomm NCS-E302 User manual

N
NC CS S- -E E3 30 02 2
S
SI IN NG GL LE E E EA AR R H HE EA AD DS SE ET T
collcomm inc
Collcomm, Inc.
TEL/FAX: [phone]
EMAIL: [e-mail]
Website: www.ncsradio.com
Using the NCS-E302 Headset with the NCS-C003 Headset Interface Box
To connect the NCS-E302 to the NCS-C003 Headset Interface Box requires the NCS-003-HSS-
TR Headset Adaptor Cable. Plug the headset 8 pin female connector into the mating connector
on the adaptor cable and tighten. Connect the 12 pin plug on the other end of the adaptor cable
to the Headset Input Jack on the NCS-C003 Headset Interface Box.
Installation of Microphone Jumpers in the NCS-C250
Microphone jumpers must be installed in the NCS-C250 to match the pin outs of the NCS-C003
Headset Interface Box. The proper installation of the mic jumpers for use with the NCS-C003 and
adaptor cable is shown below. After all jumpers are installed refer to the NCS-C250 Instruction
Manual and set the mic audio level for proper audio output.
Mic Audio
PTT
Ground
Unsel
Audio
AUXV
Sel
Audio 1 2 3 4 5 6 7 8
5V 12V
AUXV
Electret Voltage
Jumper
To NCS-C003
Headset Interface Box
To NCS-C003
NCS-003-HHS-TR
Adaptor Cable
This Section Under Revision
Contact Factory for Instructions on
Operation with NCS-C003 Headset
Interface Box

Features
Adjustable Boom
Electret Condenser Microphone Element
The headband is made of spring steel and is housed inside a rubber covering. The top
headband can be shaped for best fit and comfort. Don’t be afraid to bend it to achieve the
desired fit.
The microphone boom can be easily bent to place the microphone holder in the desired
position.
Microphone Element
The NCS-E302 headset uses an electret condenser microphone element. Electret elements
require that a DC voltage be applied to the mic audio line for proper operation. This electret
voltage is supplied by the NCS-C250 via a Special Jumper. See "Installation of Microphone
Jumpers" later in this manual.
Headset Termination
The NCS-E302 headset is terminated in an 8 pin female Foster connector. The Pin outs for
this connector are shown below.
Using the NCS-E302 with the NCS-C250 Mobile Multi-Switcher
To connect the NCS-E302 to the RJ45 mic jack on the NCS-C250 requires the NCS-250-HHS-TR
Headset Adaptor Cable. Plug the headset 8 pin female connector into the mating connector on the
adaptor cable and tighten. The RJ45 plug on the adaptor cable connects to the mic jack on the front
or rear of the NCS-C250.
Installation of Microphone Jumpers in the NCS-C250
Jumpers must be installed in the NCS-C250 so that the RJ45 mic jack pin-outs on the front and rear
panels match that of the NCS-250-HHS-TR Headset Adaptor Cable. Refer to the NCS-C250
Instruction Manual for the location of these jumpers.
The proper placement of the mic jumpers for use with the NCS-250-HHS-TR Headset and adaptor
cable is shown below.
IMPORTANT: The NCS-E302 headset requires a special jumper (shown below) for supplying the
necessary electret voltage to the headset mic element. Install only the NCS AS101802 special
jumper in the position shown. This jumper is supplied with the NCS-E302 headset or may be
installed in the NCS-C250 at the factory if purchased at the same time as the headset.
After all jumpers are installed refer to the NCS-C250 Instruction Manual and set the mic audio level
for proper audio output.
.
To Mic Jack
on NCS-C250
NCS-250-HHS-TR
Headset Adaptor Cable
Mic Audio
PTT
Ground
Unsel
Audio
AUXV
Sel
Audio 1 2 3 4 5 6 7 8
5V 12V
AUXV
Electret
Voltage
Jumper
Microphone Connector Jumper Settings
1
2
3
4
5
6
78
MIC
EAR
Gnd
Make sure no jumper
is installed on J9
Install Special Jumper
NCS P/N AS101802 in
this position.
Install Jumper on
AUXV 5V position.