Colombo R Series Guide

Lever - CB51 R - M340 - Satin Nickel
Refer to template no. 005
Refer to template no. 006E
Refer to template no. 011A
Refer to template no. 011B
Refer to template no. 006
R SERIES
PASSAGE M300 - 2” BS PRIVACY M340 - 2” BS
KEYLOCK M350- 2” BS HD KEYLOCK HDM350 - 2” BS
DOUBLE DUMMY D190 SINGLE DUMMY D185
All levers with square back plates,
include square escutcheon plates for keylock sets
HD Mortise also available in 2 " or 2¾" backset
EURO MORTISE MOUNTING

TOOLS REQUIRED:
5/8 Dia. Drill Bit, 5/8 Router Bit for Pocket,
7/8 Router Bit for face plate and PhillipsScrewdriver.
Passage Parts
1. Right Hand Lever Handle (inside)
2. Allen Key
3. Handle Set Screw (2)
4. Screws #8 (4)
5. Spring Pack
(Right Hand inside Shown)
6. Passage Spindle
7. Passage/Privacy Euro Mortise
8. Face Plate Screws (2)
9. Spring Pack (outside)
10. Left Hand Lever Handle (outside)
PLEASE NOTE
Springsare handed. Blackmust be
facing you for Right Hand Lever.
Red for Left Hand Lever.
9/16” /
13.5
mm
7/16” / 11
mm
6 7/8” / 174
mm
9/16” /
14
mm
7/8” / 22
mm
1/32”/
1
mm
27/32” / 22.5
mm
111/16” / 42.5
mm
7/8” / 22
mm
7/16” /
11.5
mm 3/8”/
9
mm
25/32” / 20
mm
1 5/8” / 42
mm
6/32”/
5
mm
1/2” /
12
mm
15/16” / 24
mm
1 11/32” / 34
mm
2 3/8” / 60
mm
3 1/4” / 82
mm
Ø7/64”/
5.5 mm
Ø 6/32” /
7.5
mm
6/16” /
9
mm
4/16”/
5.5
mm
PARTS INCLUDED WITH YOUR
NEW PASSAGE LOCK
2” / 50
mm BACKSET TEMPLATE
STRIKE TEMPLATE
IMPORTANT:
REVIEW DIAGRAMS CAREFULLY
BEFORE PREPARING DOOR
Fold on dotted line - Lay over edge of door.
Fold on dotted line - Lay over edge of door.
POINT NO. 2 (face bore)
1 3/4” door
Strike
Centre
2” door
1 3/8” door
1 3/8” door
1 3/4” door
2” door
5 3/16” / 132
mm
DRILL
DEEP
3 1/4”
80 MM
Black side
Red side
Required
hole
positioning
10
9
7
8
1
2
4
5
6
3
7 11/16” / 196
mm
1” / 26
mm
2 1/4” / 57
mm
6/16” / 8 mm
1 1/4” / 32
mm
13/16” / 21
mm
5 3/16” / 132
mm
1/2” /
12
mm 1/8” / 2.5
mm
4 7/16” / 113
mm
11/16” / 17
3” / 76 mm
1 1/4” / 32
mm
7/16” / 11
mm
15/16” / 24
mm
7/16” / 11
mm
7/16” / 11
mm
To Reverse Latch:
A.
1
2
3
1. Lift up
stopper (A).
2. Push in latch
beyond
face plate.
Rotate latch 180°
until it is in the
reverse position.
5/8” /
15
mm
Template #004 - RH
INSTALLATION INSTRUCTIONS FOR PASSAGE EURO MORTISE LOCK R M300 - non-bored door condition
Passage Strike
Euro Passage Mortise

TOOLS REQUIRED:
5/8 Dia. Drill Bit, 5/8 Router Bit for Pocket,
7/8 Router Bit for face plate and Phillips Screwdriver.
Passage Parts
1. Right Hand Lever Handle (inside)
2. Allen Key
3. Handle Set Screw (2)
4. Screws #8 (4)
5. Spring Pack
(Right Hand inside Shown)
6. Passage Spindle
7. Passage/Privacy Euro Mortise
8. Face Plate Screws (2)
9. Spring Pack (outside)
10. Left Hand Lever Handle (outside)
Privacy Parts
1. Thumbturn (inside)
2. Thumbturn Set Screw
3. Rose (inside)
4. Screws #4 (4)
5. Springless Pack (inside)
PLEASE NOTE
Springs are handed. Blackmust be
facing you for Right Hand Lever.
Red for Left Hand Lever.
9/16” /
13.5
mm
7/16” / 11
mm
6 7/8” / 174
mm
9/16” /
14
mm
7/8” / 22
mm
1/32”/
1
mm
27/32” / 22.5
mm
1 11/16” / 42.5
mm
7/8” / 22
mm
7/16” /
11.5
mm 3/8”/
9
mm
25/32” / 20
mm
1 5/8” / 42
mm
6/32”/
5
mm
1/2” /
12
mm
15/16” / 24
mm
1 11/32” / 34
mm
2 3/8” / 60
mm
3 1/4” / 82
mm
Ø7/64”/
5.5
mm
Ø 6/32” /
7.5
mm
6/16” /
9
mm
4/16”/
5.5
mm
PARTS INCLUDED WITH YOUR
NEW PRIVACY LOCK
Privacy Strike
2” / 50
mm BACKSET TEMPLATE
STRIKE TEMPLATE
IMPORTANT:
REVIEW DIAGRAMS CAREFULLY
BEFORE PREPARING DOOR
Fold on dotted line - Lay over edge of door.
Fold on dotted line - Lay over edge of door.
POINT NO. 2 (face bore)
1 3/4” door
Strike
Centre
2” door
1 3/8” door
1 3/8” door
1 3/4” door
2” door
5 3/16” / 132
mm
DRILL
DEEP
3 1/4”
80 MM
Black side
Red side
Required
hole
positioning
10
9
6
7
8
9
7
8
1
3
4
52
1
2
4
5
6
3
6. Springless Pack (outside)
7. Rose
8. Washer
9. Emergency Release Spindle
7 11/16” / 196
mm
1” / 26
mm
2 1/4” / 57
mm
6/16” / 8
mm
1 1/4” / 32
mm
13/16” / 21
mm
5 3/16” / 132
mm
1/2” /
12
mm 1/8” / 2.5
mm
4 7/16” / 113
mm
11/16” / 17
2 7/8” / 73
mm
3 9/16” / 90
mm
1” / 25.5
mm
3” / 76
mm
1 15/16” / 49.5
mm
13/16” / 21
mm
1 1/4” / 32
mm
3 9/16” / 90
mm
7/16” / 11
mm
15/16” / 24
mm
7/16” / 11
mm
7/16” / 11
mm
To Reverse Latch:
A.
1
2
3
1. Lift up
stopper (A).
2. Push in latch
beyond
face plate.
Rotate latch 180°
until it is in the
reverse position.
5/8” /
15
mm
INSTALLATION INSTRUCTIONS FOR PRIVACY EURO MORTISE LOCK R M340 - non-bored door condition
Template #005 - RH
Euro Privacy Mortise

TOOLS REQUIRED:
5/8 Dia. Drill Bit, 5/8 Router Bit for Pocket,
7/8Router Bit for face plate and Phillips Screwdriver.
PLEASE NOTE
Springs are handed. Blackmust be
facing you for Right Hand Lever.
Red for Left Hand Lever.
9/16” /
13.5
mm
7/16” / 11
mm
6 7/8” / 174
mm
9/16” /
14 mm
7/8” / 22
mm
6/16” /
9
mm
4/16”/
5.5
mm
PARTS INCLUDED WITH YOUR
NEW KEYLOCK LOCK
Keylock Strike
2” / 50
mm BACKSET TEMPLATE
STRIKE TEMPLATE
IMPORTANT:
REVIEW DIAGRAMS CAREFULLY
BEFORE PREPARING DOOR
Fold on dotted line - Lay over edge of door.
Fold on dotted line - Lay over edge of door.
POINT NO. 2 (face bore)
1 3/8” door
1 3/4” door
2” door
5 3/16” / 132
mm
DRILL
DEEP
3 1/4”
80 MM
Black side
Red side
Required
hole
positioning
7 11/16” / 196
mm
1” / 26
mm
2 1/4” / 57
mm
6/16” / 8 mm
1 1/4” / 32
mm
13/16” / 21
mm
5 3/16” / 132
mm
1/2” /
12
mm 1/8” / 2.5
mm
4 7/16” / 113
mm
11/16” / 17
2 7/8” / 73
mm
3 3/8” / 85
mm
1” / 25.5
mm
3” / 76
mm
1 15/16” / 49.5 mm
1” / 26
mm
1 1/4” / 32
mm
3 3/8” / 85
mm
7/16” / 11
mm
5/8” /
15
mm
1” / 25
mm
1 7/16” / 36
mm
2 1/16” / 52
mm
7/8” / 22
mm
167
4463 17 34
12
11
145
38
30°
5
12
22
36
35
13
11
5
1.5
Ø 5
Ø 3.5
To Reverse
Latch:
A.
1
2
3
1. Lift up
stopper
(A).
2. Push in
latch
beyond
face plate.
3. Rotate
latch 180°
until it is
in the
reverse
position.
10
9
7
7
8
1
3
5
6
2
1
2
4
5
6
3
1 3/8” door
2” door
1 3/4” door
Strike
Centre
Locking Parts
1. Profile Escutheon
2. Escutheon Mounting Bracket
3. Profile
4. Cylindar Screws
5. Screws
6. Escutheon Mounting Bracket
7. Profile Escutheon
4
Passage Parts
1. Right Hand Lever Handle (outside)
2. Allen Key
3. Handle Set Screw (2)
4. Screws #8 (4)
5. Spring Pack
(Right Hand outside Shown)
6. Passage Spindle
7. Passage/Privacy Euro Mortise
8. Face Plate Screws (2)
9. Spring Pack (inside)
10. Left Hand Lever Handle (inside)
Template #006 - RH
INSTALLATION INSTRUCTIONS FOR KEYLOCK EURO MORTISE LOCK R M350 non-bored door condition
Euro Keylock Mortise
Cylindar

TOOLS REQUIRED:
5/8 Dia. Drill Bit, 5/8 Router Bit for Pocket,
7/8 Router Bit for face plate and Phillips Screwdriver.
HDM350 HD EURO MORTISE KEYLOCK WITH 2” BACKSET TEMPLATE
9/16” /
13.5 mm
8 3/8” / 212
mm
9/16” /
14
mm
6/16” /
9
mm
4/16”/
5.5
mm
Keylock Strike
2” / 50 mm BACKSET TEMPLATE
STRIKE TEMPLATE
EURO MORTISE
KEYLOCK HDM350
LATCH TEMPLATE
IMPORTANT:
REVIEW DIAGRAMS CAREFULLY
BEFORE PREPARING DOOR
Fold on dotted line - Lay over edge of door.
Fold on dotted line - Lay over edge of door.
POINT NO. 2 (face bore)
1 3/8“ door
1 3/4“ door
2” door
6 7/8” / 175
mm
3 3/8” / 85
mm
31 / ”2/1
mm
5/8” /
15
mm
1 3/8” door
Strike
1 3/4” door
6/16” / 8
mm
1 3/8” / 34
mm
1” / 26
mm
6 7/8” / 170
mm
1/8” / 2.5 mm
1 1/8” / 29
3 3/8” / 85
mm
4 1/2” / 114
mm
mm
mm
5.461 / ”2/1 6
mm
1” / 27
mm
1 7/8” / 46.5
mm
1/2” /12
mm
4 7/16” / 113
mm
1” / 25.4 mm
3” / 76.2
2” / 50.8
1 3/16” / 30
1 1/4” / 34
mm
2 1/4” / 57.5
mm
1 3/4” / 45
Mm
2 7/16” / 62
mm
7/8” / 22
mm
For Non-bored door condition
1/2” / 13
mm
7/8” / 22 mm
HD Euro Mortise Keylock
TS INCLUDED WITH YOUR
NEW HEAVY-DUTY KEYLOCK
3 1/4”
80 MM
204
29 54 48 34
12
12
179.4
34
30°
5
12
24
39
13
12
5
1.5
Ø 5
Ø 3.5
To Reverse
Latch:
A.
1
2
3
1. Lift up
stopper
(A).
2. Push in
latch
beyond
face plate.
3. Rotate
latch 180°
until it is
in the
reverse
position.
9
7
8
1
3
2
1
2
4
6
3
2” door
DRILL
DEEP
(05/10/18)Template #006E
LEVER BORE - 5/8”
PROFILE CYLINDER
BORE - 2 X 5/8”
1 3/4” / 45
mm
1. Right Hand Profile Escutcheon
2. Profile Esc. Mounting Screws
3. Profile Cylinder
4. Profile Cylinder Screw
5
5. Mortise Screws(2)
6. Left Hand Profile Escutcheon
6
1. Right Hand Lever
2. Allan Key(2)
3. Lever Set Screw(2)
4. Lever Mounting Screws(2)
5. Passage Spindle
5
6. Passage/Privacy HD Euro Mortise
7. Left Hand Lever
8. Lever Mounting Screws(2)
9. Face Plate Screws(2)
mm
mm
1 1/2” / 38
mm
1 1/2” / 38
mm

Template for DOUBLE DUMMY D190 - non-bored door condition
Template #011A
Template for SINGLE DUMMY D185 - non-bored door condition
2-3/4” BACKSET TEMPLATE
2-3/8” BACKSET TEMPLATE
POINT NO. 2 (face bore)
Fold on dotted line - Lay over edge of door
.
DOUBLE DUMMY
SPINDLE HOLE
DRILL ONLY IF YOU
HAVE LEVER OR KNOB ON
THIS SIDE OF DOOR
5/8” DIA. (16 mm)
Determine backset
2-3/4” BACKSET TEMPLATE
2-3/8” BACKSET TEMPLATE
Fold on dotted line - Lay over edge of door
Use line markers to
locate surface mounted
dummy spindles
Template #011B
Determine backset
PLASTIC ADAPTOR NOT USED FOR HD
SERIES & ROSES WITH 6MM CONCEPT
PLASTIC ADAPTOR NOT USED FOR HD
SERIES & ROSES WITH 6MM CONCEPT