ColorGATE RAPID SPECTRO CUBE LED User manual

RAPID SPECTRO CUBE LED
MANUAL
LAST UPDATED 12/2021
© 12/2021 ColorGATE Digital Output Solutions GmbH

Publisher
ColorGATE Digital Output Solutions GmbH
Grosse Duewelstrasse 1
30171 Hannover
Germany
Contact
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.colorgate.com
The soft- and hardware names used in this manual are in most cases registered trademarks and are
subject to legal rights. Information in this manual is subject to the patent protection rights. In this
publication contained texts and images of the documented product is copyrighted material. All rights
are reserved. Also rights for reproduction in photocopying, presentation, television, radio are
reserved. A print-out of this manual is expressly permitted for ColorGATE sales partners and
customers. Product names have been used here without a permission of an unrestricted usage.
Images and texts have been arranged carefully. Nevertheless mistakes cannot be excluded completely.
ColorGATE Digital Output Solutions GmbH is not responsible for incorrect information and its
consequences. A legal responsibility or commitment is impossible.
ColorGATE Digital Output Solutions GmbH appreciates any feedback and suggestions for improving
the documentation. Please send your comments by email to [e-mail].
© Copyright 1996-2021 ColorGATE Digital Output Solutions GmbH
Updated 12/1/2021
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 2 of 34

Contents
1 Basic device information 5
1.1 Technical specifications 5
1.2 Environmental conditions 5
1.3 Nameplate 5
1.4 Scope of delivery 6
1.5 Intended Use 11
1.6 Components 11
2 About this manual 16
2.1 Scope 16
2.2 Warning signs 16
3 Safety 18
3.1 Preliminary notes on safety 18
3.2 Safety instructions 18
3.2.1 General safety instructions 18
3.2.2 Safety instructions for the mechanical system 18
3.2.3 Safety instructions for electrical systems 19
3.2.4 Information regarding repairs 20
3.3 Personal protective equipment 20
3.4 Protective devices 20
4 Assembly 21
5 Operation 30
6 Cleaning 31
7 Spare Parts 32
8 Disposal 33
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 3 of 34

9 Appendix 34
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 4 of 34

1 Basic device information
1 Basic device information
This chapter contains the following information about the device:
lTechnical specifications: see page 5
lNameplate: see page 5
lScope of delivery: see page 6
lIntended Use: see page 11
1.1 Technical specifications
Physical Dimensions
lPhysical Dimensions: 410 mm x 510 mm x 610 mm
lWeight (empty): 14.8 kg
Electrical power supply
lSupply voltage: 100 to 240 V AC 50/60Hz
lRated current: 1 A (max. 6 A)
lProtection class: I
lIP Code: IP20
1.2 Environmental conditions
lAltitude: Max. 2000 m
lAmbient temperature: Max. 40oC
lRelative humidity: 10-80%
lMains supply voltage fluctuations: ± 10%
lOvervoltage category: II
lPollution degree: PD2
1.3 Nameplate
The nameplate is located on the back of the device:
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 5 of 34

1 Basic device information
1.4 Scope of delivery
Hardware
The scope of delivery for the Rapid Spectro Cube includes the parts listed below:
Positi
on
Descript
ion Image
Rapid
Spectro
Cube LED
main unit
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 6 of 34

1 Basic device information
Positi
on
Descript
ion Image
Drawer
section
with
connectio
n
elements
Lift table
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 7 of 34

1 Basic device information
Positi
on
Descript
ion Image
Camera
(Nikon
D780)
USB cable
(2x)
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 8 of 34

1 Basic device information
Positi
on
Descript
ion Image
Calibratio
n chart
White
plate
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 9 of 34

1 Basic device information
Positi
on
Descript
ion Image
Black
plate
USB cable
rectangul
ar
Software
Additionally, the following software products are required to operate the RSC LED:
lColorGATE Productionserver 21
lRSCCaptureV2 software package for Productionserver
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 10 of 34

1 Basic device information
You can download the software in our Service & Support Area under Download > Software &
Updates (registration required). Please refer also to our Getting Started Guide for Productionserver.
You can download it from our website.
1.5 Intended Use
The Rapid Spectro Cube LED is an optical, electrical measurement device. Its intended use is the
measurement of color on various printable substrates in order to create an ICC output profile for
different color models. The device is a product in the sense of the Low Voltage Directive 2014/35/EU
and the Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
To prevent personal injury or property damage, use the device only as described in the user
documentation. Any other use is considered to be improper. ColorGATE will assume no liability for
damages resulting from improper use.
1.6 Components
Main unit with drawer section - front view
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 11 of 34

1 Basic device information
Position Description
Casing
Main switch
Carrying handles
Drawer
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 12 of 34

1 Basic device information
Main unit - top view with removed lid
Position Description
Automatic circuit breaker
Fan/controller supply
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 13 of 34

1 Basic device information
Position Description
LED controller
Camera (Nikon D780)
USB connections for the LED controller and for data transferred to the PC (position 3)
Fan
LED power supply
Power supply unit
Main unit - rear view
Position Description
Fan
USB ports
Power supply
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 14 of 34

1 Basic device information
LED light strips
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 15 of 34

2 About this manual
2 About this manual
This chapter contains the following information about using this manual:
lScope: see page 16
lWarning signs: see page 16
2.1 Scope
This manual provides you with information about the Rapid Spectro Cube LED. It gives you information
regarding:
lSafety
lInitial setup
lOperation
lMaintenance
lDisposal
The operating company is responsible for the safekeeping of all manufacturer's documents including
this manual. The manual must always be available to the user.
This manual is supplemented by the following additional documentation:
lRSCCapture V2 Software Manual
lNikon D780 Camera Manual
2.2 Warning signs
The warnings in these operating instructions are marked with warning signs and signal words. The
type of danger is indicated by the warning sign and the signal words.
The preceding warnings are structured as follows:
Warning
Nature and source of the hazard, possible consequences
lMeasures to avoid the hazard
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 16 of 34

2 About this manual
Meaning of the signal words
lDANGER: immediate risk of danger to life or serious physical injury
lWARNING: possible risk of fatal injury or serious bodily harm
lCAUTION: possible risk of minor or moderate bodily injury
lNOTICE: Possible risk of property damage
Meaning of the pictograms
General warning sign
Warning against electrical hazards
Warning against hand injuries
Wear personal protective equipment
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 17 of 34

3 Safety
3 Safety
This chapter contains the following information on operating the device safely:
lPreliminary notes on safety: see page 18
lSafety instructions: see page 18
lPersonal protective equipment: see page 20
lProtective devices: see page 20
3.1 Preliminary notes on safety
The Rapid Spectro Cube LED was designed and manufactured according to the state of the art. The
results of the risk assessment were taken into account in the design.
If the Rapid Spectro Cube LED is used as intended, the hazards that can arise from normal operation
are reduced to a minimum.
3.2 Safety instructions
3.2.1 General safety instructions
lThe Rapid Spectro Cube LED is intended for indoor use only. The device must not be used
outdoors or in tropical climates.
lTo ensure trouble-free operation of the unit, damaged and/or worn parts must be replaced in
good time.
lThe device must be switched off for maintenance and repair work.
lDirt and objects lying around cause slipping and tripping hazards. Injuries can be caused in the
event of a fall. Keep the work area clean and eliminate tripping hazards.
3.2.2 Safety instructions for the mechanical system
lDo not use the Rapid Spectro Cube LED if you do not know how to operate it.
lOnly install or work on the Rapid Spectro Cube LED if you have been trained and instructed in
its operation.
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 18 of 34

3 Safety
lEven though the Rapid Spectro Cube LED has been designed and built safely and is equipped
with safety precautions, hazards may still arise from the device. This is particularly the case if
specified operating sequences and safety instructions are disregarded. Protect yourself and
others by working according to regulations.
lDo not climb on the Rapid Spectro Cube LED and do not use it as a climbing aid or as a shelf.
lKeep the area around the Rapid Spectro Cube LED as well as the escape routes free of objects
that pose a tripping hazard and may hinder rapid evacuation.
lPay attention to unusual behavior during operation of the Rapid Spectro Cube LED, as this may
indicate an imminent malfunction that could result in a potentially dangerous situation.
lSome parts of the Rapid Spectro Cube LED pose an increased risk of injury due to crushing and
entrapment of limbs and impact with protruding components.
lNever dismantle, bypass or render protective devices unusable. Electrical equipment poses a
danger to life!
lWhen working with heavy parts, use suitable lifting equipment to avoid spinal injuries.
lWear appropriate personal protective equipment during assembly, maintenance and cleaning
work.
lInjecting liquids into the device when it is connected to the power supply can cause a short
circuit.
lWhen working with and on the Rapid Spectro Cube LED, use only compatible and intact tools
and suitable equipment. Defective tools can cause injuries.
lDo not make any unauthorized changes to the device, or the Rapid Spectro Cube LED will lose
its conformity as a result.
lDo not leave any tools or objects on the Rapid Spectro Cube LED after work. They could impair
the function of the device.
3.2.3 Safety instructions for electrical systems
lOnly qualified electricians may work on the electrical equipment of the Rapid Spectro Cube LED.
lWhen replacing electrical components, only install parts with the same specification.
Warning
Injuries from electric shock when using wrong mains power supply cord
lDo not use a mains power supply cord with insufficient rating.
lBefore switching on the Rapid Spectro Cube LED, make sure the correct
mains power supply cord is connected.
lIf the mains power supply cord needs to be replaced, make sure to switch off
the power supply and replace the cord with a cord that has the correct
rating.
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 19 of 34

3 Safety
3.2.4 Information regarding repairs
Note: In case the Rapid Spectro Cube LED needs to be repaired, please contact ColorGATE for further
details on how to proceed.
3.3 Personal protective equipment
The operating company is responsible for the provision of appropriate protective equipment and for
its use. The operating company monitors the wearing of the PPE.
3.4 Protective devices
lInsulation, protection against electric shock (ensures protection against accidental contact with
active parts): casing, drawer, interior where LEDs are located
lIEC 320 C13 plug corresponding to IEC 320 C14 socket for easy disconnection
lLighting supplied by a class I power supply unit
lDependent on the regulations of overvoltage category II in an office environment: residual
current circuit breaker, rated at 30mA and current tripping circuit breaker, (RCD) rated at max.
16A.
ColorGATE Rapid Spectro Cube LED Hardware Manual — Updated
12/1/2021 Page 20 of 34