COMBA OY-YN-V11P User manual

Comba Telecom Inc. 568 Gibraltar Drive, Milpitas, CA 95035. http://www.combausa.com/
Tel: [phone], [e-mail], Fax: [phone]
Information contained in this document is subject to confirmation at time of ordering. Specifications may differ depending on region and customers’ requirements.
Page 1 of 2
DS-Control
2-0-0/1221
Outdoor Directional Yagi Antenna
OY-YN-V11P
450-512MHz, N-Female
•Covering 450-512MHz Public Safety Band
•Narrow beamwidth and High gain with 8 elements
•Suitable for donor antenna and aluminum finished
•Supporting antenna tilt adjustment with ± 15
Electrical Specification
Product Model
OY-YN-V11P
Frequency (MHz)
450-512
Gain (dBi)
11.0 ± 1.0
Polarization
Linear / Preinstalled with Vertical Pol.
Beamwidth Horizontal (°)
50.0 ± 5.0
Beamwidth Vertical (°)
48.0 ± 5.0
VSWR
≤1.5
Front to Back Ratio (dB)
≥13
Average Power, max (W)
100
Impedance (ohm)
50
Mechanical Specification
Environment & Compliance
Dimension Diameter, height (in/mm)
43.31 x 14.17 x 3.35 / 1100 x 360 x 85
Application
Outdoor
Weight (lb./kg)
2.70 / 1.20
Operating Temperature
-40°C to +60°C
Shipping Dimension(in/mm)
44.09 x 14.76 x 3.54 / 1120 x 375 x 90
Relative Humidity
Up to 95%
Shipping Weight(lb./kg)
4.45 / 2.02
RoHS
Compliant
Radome Material & color
Aluminum finished, White
Lightning protection
Direct Grounding
Diameter of the pole mounting pole (in/mm)
1.65-2.05 / 42-52
Mounting bracket Materials
Zinc Plated Steel
Antenna Tilt adjustment ()
± 15
Maximum Wind Speed(mph)
175
Connector type
N-Female
Antenna Pattern
Horizontal Vertical
450MHz 480MHz 512MHz

Comba Telecom Inc. 568 Gibraltar Drive, Milpitas, CA 95035. http://www.combausa.com/
Tel: [phone], [e-mail], Fax: [phone]
Information contained in this document is subject to confirmation at time of ordering. Specifications may differ depending on region and customers’ requirements.
Page 2 of 2
DS-Control
2-0-0/1221
Mechanical Drawing and Installation Guide
Installation Instruction
A. The antenna bracket and the antenna frame are pre-assembled for vertical polarization (default)
B. Put the antenna bracket and the mounting pole according to the position and direction shown in the drawing.
C. Fasten two U-bolts and the mounting bracket to the mounting pole (not included) with Hex M8 nut.
D. Connect the equipment and the antenna with their respective connector.
E. Ensure that all connections are waterproof.
F. Fasten the cables of the antenna and equipment.
15°
2.48 [63.0]
3.67 [93.3]
2.36 [60.0]
3.39 [86.2]
0.81 [20.7]
15°
Antenna frame
(pre-assembled
With vertical polarization)
Antenna bracket
U-Bolt pole mounting
U-Bolt
Hex nut M8
Antenna Tilt
Adjustment
Antenna frame
Antenna
mounting bracket
Mounting pole
15°
U-Bolt
Antenna frame
Antenna mounting
bracket
Mounting pole
Ø 42-52mm / 1.65-2.05inches
Antenna Tilt
Adjustment
Mounting Pole
Ø1.65-2.05 (inches)/ Ø42-52 (mm)
U-Bolt
Pole Mounting
M8 Plain Washer
M8 Spring Washer
M8 Hex Nut