Comco ProCenter Plus User manual

ProCenterPlus
Manual
Maintenance
AbrasiveContainmentandDisposal
Emptytheabrasivehopperbyplacingapail
orplasticbagundereitherofthehopper
outletsandopenthevalve.
Emptythecontainerandrepeatasneeded.
Warning:Excessiveabrasiveinthehoppermay
causepowdertoleakthroughventholes.
FilterCleaners
Filtercleaningmalletsarelocatedonboth
sidesoftheProCenterPlus.Beforeeach
shift,withthepowerturnedoff,pulland
releasethemalletstwoorthreetimes.
Thisactionwilldislodgespentmediathat
mayhavecollectedintheHEPAfilter.
ChangingtheHEPAFilter
Removeanyequipmentsitting
ontopofthefilterbox.
Disconnectthepowercords
onbothsidesofthefilterbox.
Removefilterboxcover.
Removeandreplacefilter.
(CTR280‐1ReplacementHEPA
filterassembly)
AirDryerMaintenance
Thedesiccantinsidetheairdryerbowlwillgraduallyturnfrombright
orangetodarkgreenasitbecomessaturated.Changeaccordingto
theinstructionsincludedwiththe
airdryer.
Formaintenanceinstructionsonyour
airdryer,pleaseseemanual“AD5100
Series– DesiccantAirDryer.”
NEED HELP? Comco Tech Support: 818‐841‐5500
[e-mail] www.comcoinc.com
8/2021 TS414

HAND‐
PIECE
HOSE
POWER
CORD
BLASTER
POWER
CORD
AIR
FROM
DRYER
VENT
HOSE
SHOP
AIR
TOAIR
DRYER
Set‐upGuide
Theairpressureregulatorsarepresetatthe
factoryforreasonableairflowandshould
notrequireadjustmentwiththedemands
ofnormalproduction.
InstallAirDryer
Theairdryerunitispreassembledand
onlyrequiresmountingtothe
ProCenterPlusandconnectionofair
hoses.
•Locatescrewholesandpositionair
dryeronsideofProCenterPlus
•Raisedryercartridgetofacilitate
drivingscrews
•Connectairhoses
Blow‐OffGun
Cleananypowderresiduefromthepartwith
aquickblastofair.
•Graspthegunasshown.
•Applypressurewithyourthumbtodirect
ablastofair.
Themorethetipisbent,thegreaterthe
volumeofairreleased.
AirPressureRegulators
Therearetwoairregulatorcontrolsonthe
electronicsboxlocatedonbackoftheunit.
•AirPurge:regulatesflowtotheairjets;
preventsabrasivefromaccumulatingin
frontoftheworkchamber.
Note:Thereshouldalwaysbeairflowing
outoftheairjets
•Blow‐Off:setsairpressureontheblow‐off
gun
Connections
•Feedhandpiece fromblasterintoworkchamber
•AttachventhosetobackbyslippingQuicknut
overhose,workingthehoseoverthenipple,
thenhandtightenQuicknut ontofitting.
•Connectcleartubingfromairdryertoblaster
inletairconnector
•Connectblacktubingfromairdryertoinletairteefitting
•Connectshopairusinga¼”IndustrialShapeQuick‐Disconnect
(customersupplied).Example:Foster3SeriesSG1513orMcMaster
Carr6536K38
•ConnectpowersourcetoProCenterPlus
•ConnectblasterpowercordtoProCenterPlus
Warning:ProCenterPlus
outletsaredesignedto
supplypowerforblasters
onlyandshouldnotbe
usedforoperatingother
equipment.
Beforeyousetupand
operateyourComco
blaster,readandfollow
thesafetyinstructionsin
yourMaintenanceManual.